CISPR 16-1:1999+AMD1:2002 CSV
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus
Amended by
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
19-11-2003
Language(s)
English - French
Published date
23-10-2002
Publisher
FOREWORD
TABLE RECAPITULATING CROSS-REFERENCES
1 Scope
2 Normative references
3 Definitions
4 Measuring apparatus
4.1 Quasi-peak measuring receivers for the frequency
range 9 kHz to 1000 MHz
4.2 Peak measuring receivers for the frequency range
9 kHz to 1000 MHz
4.3 Average measuring receivers for the frequency range
9 kHz to 1000 MHz
4.4 RMS measuring receivers for the frequency range 9 kHz
to 1000 MHz
4.5 Spectrum analyzers and scanning receivers
4.6 Audio-frequency voltmeter
5 Ancillary apparatus
5.1 Artificial mains networks
5.2 Current and voltage probes
5.3 Absorbing clamp for use in the frequency range 30 MHz
to 1000 MHz
5.4 Disturbance analyzers
5.5 Antennas for measurement of radiated radio disturbance
5.6 Test sites for measurement of radio disturbance field
strength for the frequency range of 30 MHz to 1000 MHz
5.7 Reverberating chamber for total radiated power measurement
5.8 Coupling units for conducted current immunity measurement
5.9 TEM cells for immunity to radiated disturbance measurement
5.10 Coupling devices for measuring signal lines
5.11 The artificial hand and series RC element
5.12 Test sites for measurement of radio disturbance field
strength for the frequency range 1 GHz to 18 GHz
5.13 Specifications and validation procedures for a test
site to be used to calibrate antennas in the frequency
range of 30 MHz to 1000 MHz
Annex A (normative) Determination of response to repeated pulses
of quasi-peak and r.m.s. measuring receivers (subclauses
3.2, 4.1.4.2, 4.4.2.2 and 4.4.4.1)
Annex B (normative) Determination of pulse generator spectrum
(subclauses 4.1.4, 4.2.4, 4.3.4, 4.4.4)
Annex C (normative) Accurate measurements of the output of
nanosecond pulse generators (subclauses 4.1.4, 4.2.4,
4.3.4, 4.4.4)
Annex D (normative) Influence of the quasi-peak measuring
receiver characteristics on its pulse response
(subclause 4.1.4.2)
Annex E (normative) Response of average and peak measuring
receivers (subclause 4.3.2.1)
Annex F (normative) Artificial mains networks (subclause 5.1)
Annex G (normative) Validation procedure of the open area test
site for the frequency range of 30 MHz to 1000 MHz
(subclause 5.6)
Annex H (normative) Calibration of the absorbing clamp
(subclause 5.3)
Annex I (informative) Construction, frequency range, and
calibration of current probes (subclause 5.2)
Annex J (informative) Construction of the absorbing clamp
(subclause 5.3)
Annex K (informative) Construction details for open area test
sites in the frequency range of 30 MHz to 1000 MHz
(subclause 5.6)
Annex L (informative) Basis for 4 dB site acceptability
criterion (subclause 5.6)
Annex M (informative) Construction of the coupling units for
current injection for the frequency range 0,15 MHz to
30 MHz (subclause 5.8)
Annex N (informative) Principle of operation and examples of
coupling units for conducted current immunity
measurements (subclause 5.8)
Annex O (normative) Parameters of broadband antennas
Annex P (normative) Loop antenna system for magnetic field
induced current measurements in the frequency range of
9 kHz to 30 MHz
Annex Q (normative) Example and measurement of an asymmetrical
artificial network (AAN)
Annex R (informative) CALTS requirements (subclause 5.13)
Annex S (informative) Test antenna considerations (subclause
5.13)
Annex T (informative) Antenna and site attenuation theory
(subclause 5.13)
Annex U (informative) Application of a fixed length dipole
(30 MHz <= f <= 80 MHz) (subclause 5.13)
Annex V (informative) Pascal Program used in T.1.3 (subclause
5.13)
Annex W (informative) Checklist validation procedure (subclause
5.13)
Annex X (normative) Monopole (1 m rod antenna) performance
equations and characterization of the associated antenna
matching network
Annex Y (normative) Performance check of the exceptions from the
definitions of a click according to 4.2.3 of CISPR 14-1
Annex Z (normative) Example and measurement of the parameters of
the AN for coaxial and other screened cables
Figures 1 to Z.2
Specifies the characteristics and performance of equipment for the measurement of radio disturbance voltages, currents and fields in the frequency range 9 kHz to 18 GHz. In addition, requirements are specified for specialized equipment for discontinuous disturbance measurements. The requirements include the measurement of broadband and narrowband types of radio disturbance. Replaces the first edition published in 1993, amendment 1 (1997) as well as consolidated edition 1.1 (1998).
| Committee |
CISPR/CIS/A
|
| DevelopmentNote |
Also numbered as BS CISPR 16-1(1999) (04/2003) Supersedes CISPR 1, CISPR 2, CISPR 3, CISPR 4, CISPR 5, and CISPR 6. (07/2004)
|
| DocumentType |
Standard
|
| Pages |
422
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN CISPR 16-1 : 1999 AMD 2 2003 | Identical |
| NF EN 55016-1 : 2003 PR | Identical |
| DIN VDE 0876-16-1 : DRAFT AMD 2 2002 | Identical |
| VDE 0876-16-1 : DRAFT AMD 2 2002 | Identical |
| AS/NZS CISPR 16.1:2002 | Identical |
| BS CISPR 16-1:1998 | Identical |
| DIN VDE 0876-16-1 : DRAFT AMD 2 2002 | Corresponds |
| CEI EN 60437 : 1998 | RADIO INTERFERENCE TEST ON HIGH-VOLTAGE INSULATORS |
| 14/30300746 DC : 0 | BS EN 60358-4 ED 1.0 - COUPLING CAPACITORS AND CAPACITOR DIVIDERS - PART 4: AC AND DC SINGLE-PHASE CAPACITOR-DIVIDER AND RC-DIVIDER |
| CSA CISPR 12:2010 | VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS |
| 01/200383 DC : DRAFT JAN 2001 | IEC 61000-4-6 ED.2 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES. IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
| CSA CEI/IEC 61000.4.6 : 0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4: TESTING AND MEASUREMENT TECHNIQUES - SECTION 6: IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
| I.S. EN 60437:1999 | RADIO INTERFERENCE TEST ON HIGH-VOLTAGE INSULATORS |
| BS EN 50240:2004 | Electromagnetic compatibilty (EMC). Product standard for resistance welding equipment |
| DIN V ENV 50121-2 : 1997 | BAHNANWENDUNGEN - ELEKTROMAGNETISCHE VERTRAEGLICHKEIT - STOERAUSSENDUNG DES GESAMTEN BAHNSYSTEMS IN DIE AUSSENWELT |
| BS ISO 14302:2002 | Aerospace series. Space systems. Electromagnetic compatibility requirements |
| BS ISO 19292:2014 | Ships and marine technology. Lifesaving and fire protection. Point-type resettable flame detectors for ships |
| 03/112147 DC : DRAFT JULY 2003 | IEC 61967-3 ED.1 - INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 3: MEASUREMENT OF RADIATED EMISSIONS - SURFACE SCAN METHOD |
| 08/30179863 DC : DRAFT MAR 2008 | BS EN 55013 AMD3 - SOUND AND TELEVISION BROADCAST RECEIVERS AND ASSOCIATED EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| NF EN 302498-1 : 2011 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - SHORT RANGE DEVICES (SRD) - TECHNICAL CHARACTERISTICS FOR SRD EQUIPMENT USING ULTRA WIDEBAND TECHNOLOGY (UWB) - OBJECT DISCRIMINATION AND CHARACTERIZATION APPLICATIONS FOR POWER TOOL DEVICES OPERATING IN THE FREQUENCY BAND FROM 2,2 GHZ TO 8,5 GHZ - PART 1: TECHNICAL CHARACTERISTICS AND TEST METHODS |
| TS 103 051 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); EXPANDED MEASUREMENT UNCERTAINTY FOR THE MEASUREMENT OF RADIATED ELECTROMAGNETIC FIELDS |
| CEI EN 60942 : 2004 | ELECTROACOUSTICS SOUND CALIBRATORS |
| 05/30135559 DC : 0 | EN 50471 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT FAMILY EMISSION STANDARD FOR WIRE-LINE TELECOMMUNICATION NETWORKS |
| 04/30111859 DC : 0 | IEC 62271-1 - HIGH-VOLTAGE SWITCHGEAR AND CONTROL GEAR - PART 1: COMMON SPECIFICATIONS |
| NF EN 300132-3 : 2003 | ENVIRONMENTAL ENGINEERING (EE) - POWER SUPPLY INTERFACE AT THE INPUT TO TELECOMMUNICATIONS EQUIPMENT - PART 3: OPERATED BY RECTIFIED CURRENT SOURCE, ALTERNATING CURRENT SOURCE OR DIRECT CURRENT SOURCE UP TO 400 V |
| NFR 13 008-1 : 1999 | ROAD VEHICLES - ELECTROMAGNETIC COMPATIBILITY TEST PROCEDURE OF MOTOR VEHICLES - PART 1: DEFINITIONS AND GENERALITIES |
| 02/208194 DC : DRAFT AUG 2002 | IEC 62132-4 ED.1.0 - INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC IMMUNITY - PART 4: MEASUREMENT OF CONDUCTED IMMUNITY - DIRECT RF POWER INJECTION METHOD |
| 04/30115021 DC : DRAFT JUL 2004 | CLC TR 50426 - ASSESSMENT OF INADVERTENT INITIATION OF BRIDGE WIRE ELECTRO-EXPLOSIVE DEVICES BY RADIOFREQUENCY RADIATION - GUIDE |
| S.R. CLC/TR 50485:2010 | ELECTROMAGNETIC COMPATIBILITY - EMISSION MEASUREMENTS IN FULLY ANECHOIC CHAMBERS |
| BS EN 61967-1:2002 | Integrated circuits. Measurement of electromagnetic emissions, 150 kHz to 1 GHz General conditions and definitions |
| I.S. EN 61800-3:2005 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004 (EQV)) |
| 01/200684 DC : DRAFT FEB 2001 | |
| DIN V ENV 50121-4 : 1997 | BAHNANWENDUNGEN - ELEKTROMAGNETISCHE VERTRAEGLICHKEIT - STOERAUSSENDUNG UND STOERFESTIGKEIT VON SIGNAL- UND TELEKOMMUNIKATIONSEINRICHTUNGEN |
| 00/705404 DC : DRAFT FEB 2000 | |
| 01/200932 DC : DRAFT APR 2001 | PREN 50XXX - MAINS SIGNALLING - HF EMISSION AND IMMUNITY |
| 97/209093 DC : 0 | |
| 04/30116621 DC : DRAFT JUL 2004 | EN 50121-3-2 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 3-2: ROLLING STOCK - APPARATUS |
| BS EN 50065-2-2:2003 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in industrial environments |
| CEI CLC/TR 50426 : 2005 | ASSESSMENT OF INADVERTENT INITIATION OF BRIDGE WIRE ELECTRO-EXPLOSIVE DEVICES BY RADIO-FREQUENCY RADIATION - GUIDE |
| CSA C60044-5:2007 | INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| CSA C61000-4-6 : 2009 : R2014 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
| CLC/TR 50485:2010 | Electromagnetic compatibility - Emission measurements in fully anechoic chambers |
| SAE J ISO 13766 : FEB 2003 | EARTH-MOVING MACHINERY - ELECTROMAGNETIC COMPATIBILITY |
| CSA C60044-5 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| CEI R210-010 : 2004 | ELECTROMAGNETIC COMPATIBILITY - EMISSION MEASUREMENTS IN FULLY ANECHOIC CHAMBERS |
| IEC 61851-21:2001 | Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c./d.c. supply |
| CSA C61000-4-6 : 2009 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
| I.S. EN 60694:1999 | COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS |
| I.S. EN 50289-1-6:2002 | COMMUNICATION CABLES - SPECIFICATIONS FOR TEST METHODS - PART 1-6: ELECTRICAL TEST METHODS - ELECTROMAGNETIC PERFORMANCE |
| TS 134 124 : 13.0.0 | UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS FOR MOBILE TERMINALS AND ANCILLARY EQUIPMENT (3GPP TS 34.124 VERSION 14.0.0 RELEASE 14) |
| I.S. EN 50370-1:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT FAMILY STANDARD FOR MACHINE TOOLS - PART 1: EMISSION |
| CSA CISPR 11 : 2004 : R2017 | INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) RADIO-FREQUENCY EQUIPMENT - ELECTROMAGNETIC DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| I.S. EN 60945:2002 | MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - GENERAL REQUIREMENTS - METHODS OF TESTING AND REQUIRED TEST RESULTS |
| NF EN 302435-1 : 2010 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - SHORT RANGE DEVICES (SRD) - TECHNICAL CHARACTERISTICS FOR SRD EQUIPMENT USING ULTRA WIDEBAND TECHNOLOGY (UWB) - BUILDING MATERIAL ANALYSIS AND CLASSIFICATION EQUIPMENT APPLICATIONS OPERATING IN THE FREQUENCY BAND FROM 2,2 GHZ TO 8,5 GHZ - PART 1: TECHNICAL CHARACTERISTICS AND TEST METHODS |
| UNE-EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| 09/30162904 DC : 0 | BS EN 61204-3 - LOW-VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC) |
| IEC 60694:1996+AMD1:2000+AMD2:2001 CSV | Common specifications for high-voltage switchgear and controlgear standards |
| EN 60651:1994/A2:2001 | SOUND LEVEL METERS (IEC 60651:1979/A2:2000) |
| EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| EN 60694:1996/A2:2001 | COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS |
| EN 60270:2001/A1:2016 | HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015) |
| EN 61967-1:2002 | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 1: General conditions and definitions |
| EN 61967-5:2003 | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 5: Measurement of conducted emissions - Workbench Faraday Cage method |
| EN 61284:1997 | Overhead lines - Requirements and tests for fittings |
| EN 60945:2002 | Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results |
| EN 60044-5:2004 | Instrument transformers - Part 5: Capacitor voltage transformers |
| EN 60315-4:1998 | Methods of measurement on radio receivers for various classes of emission - Part 4: Receivers for frequency-modulated sound broadcasting emissions |
| EN 55012:2007/A1:2009 | VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS |
| EN 50147-2 : 1996 | ANECHOIC CHAMBERS - PART 2: ALTERNATIVE TEST SITE SUITABILITY WITH RESPECT TO SITE ATTENUATION |
| EN 302 291-1 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); SHORT RANGE DEVICES (SRD); CLOSE RANGE INDUCTIVE DATA COMMUNICATION EQUIPMENT OPERATING AT 13,56 MHZ; PART 1: TECHNICAL CHARACTERISTICS AND TEST METHODS |
| EN 60255-25:2000 | Electrical relays - Part 25: Electromagnetic emission tests for measuring relays and protection equipment |
| 14/30279327 DC : 0 | BS EN 61800-3 AMD2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS |
| BS EN 60358-1:2012 | Coupling capacitors and capacitor dividers General rules |
| CEI EN 50065-7 : 2002 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 7: EQUIPMENT IMPEDANCE |
| BS EN 60044-5:2004 | Instrument transformers Capacitor voltage transformers |
| 00/244020 DC : DRAFT SEP 2000 | IEC 61800-3 ED.2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS PRODUCT STANDARD INCLUDING SPECIFIC TEST METHODS |
| EN 60437:1997 | Radio interference test on high-voltage insulators |
| BS EN 60942:2003 | Electroacoustics. Sound calibrators |
| CSA M14982 : 2000 | AGRICULTURAL AND FORESTRY MACHINERY - ELECTROMAGNETIC COMPATIBILITY - TEST METHODS AND ACCEPTANCE CRITERIA |
| NF EN 301011 : 2000 | |
| 04/30115023 DC : DRAFT JUL 2004 | CLC TR 50427 - ASSESSMENT OF INADVERTENT IGNITION OF FLAMMABLE ATMOSPHERES BY RADIO-FREQUENCY RADIATION - GUIDE |
| BS EN 61000-5-7:2001 | Electromagnetic compatibility (EMC). Installation and mitigation guidelines Installation and mitigation guidelines. Degrees of protection by enclosures against electromagnetic disturbances (EM code) - Degrees of protection against electromagnetic disturbances provided by enclosures (EM code) |
| 07/30167396 DC : 0 | BS EN 61869-4 - INSTRUMENT TRANSFORMERS - PART 4 - SPECIFIC REQUIREMENT FOR COMBINED TRANSFORMERS |
| NF ETS 300342-3 : 2001 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - ELECTROMAGNETIC COMPATIBILITY (EMC) FOR EUROPEAN DIGITAL CELLULAR TELECOMMUNICATIONS SYSTEM (GSM 900 MHZ AND DCS 1800 MHZ) - PART 3: BASE STATION RADIO AND ANCILLARY EQUIPMENT AND REPEATERS MEETING PHASE 2 GSM REQUIREMENTS |
| 07/30167174 DC : 0 | BS EN 61869-2 - INSTRUMENT TRANSFORMERS - PART 2: SPECIFIC REQUIREMENT FOR CURRENT TRANSFORMERS |
| DIN EN 50147-2 : 1996 | ANECHOIC CHAMBERS - PART 2: ALTERNATIVE TEST SITE SUITABILITY WITH RESPECT TO SITE ATTENUATION |
| 04/30112111 DC : DRAFT APR 2004 | CENELEC TS PRTS 50437 - ELECTROMAGNETIC EMISSIONS FROM ACCESS POWERLINE COMMUNICATIONS NETWORKS |
| TR 102 750 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); RADAR LEVEL GAUGING APPLICATIONS IN STILL PIPES |
| NF EN 61204-3 : 2001 | LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC) |
| BS EN 60315-4:1998 | Methods of measurement on radio receivers for various classes of emission Receivers for frequency-modulated sound broadcasting emissions |
| BS EN 61800-3 : 2004 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS |
| 04/30116077 DC : DRAFT JUL 2004 | |
| DIN ETS 300456:1996-06 | SATELLITE EARTH STATIONS AND SYSTEMS (SES) - TEST METHODS FOR VERY SMALL APERTURE TERMINALS (VSATS) OPERATING IN THE 11/12/14 GHZ FREQUENCY BANDS |
| BS CISPR 16-3:2000 | Specification for radio disturbance and immunity measuring apparatus and methods Reports and recommendations of CISPR |
| BS EN 50370-1:2005 | Electromagnetic compatibility (EMC). Product family standard for machine tools Emission |
| BS CISPR 16-2:1996 | Specification for radio disturbance and immunity measuring apparatus and methods Methods of measurement of disturbances and immunity |
| BS EN 61967-4 : 2002 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 4: MEASUREMENT OF CONDUCTED EMISSIONS - 1 OHM/150 OHM DIRECT COUPLING METHOD |
| 03/111744 DC : DRAFT JULY 2003 | |
| 04/30112722 DC : DRAFT APR 2004 | IEC 60044-5 ED.1 - INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| DIN V ENV 50121-3-1 : 1997 | BAHNANWENDUNGEN - ELEKTROMAGNETISCHE VERTRAEGLICHKEIT - SCHIENENFAHRZEUGE - ZUG UND GESAMTES FAHRZEUG |
| TS 103 085 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); SHORT RANGE DEVICES (SRD) USING ULTRA WIDE BAND (UWB) FOR LOCATION AND TRACKING RAILROAD APPLICATIONS; RF CONFORMANCE TESTING |
| CEI EN 50370-1 : 2006 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT FAMILY STANDARD FOR MACHINE TOOLS - PART 1: EMISSION |
| BS IEC 61000-3.8 : 1997 | ELECTROMAGNETIC COMPATIBILITY (EMC) - LIMITS - GUIDE TO SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS - EMISSION LEVELS, FREQUENCY BANDS AND ELECTROMAGNETIC DISTURBANCE LEVELS |
| BS EN 60730-1 95 : 95 AMD 12021 | SPECIFICATION FOR AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - GENERAL REQUIREMENTS |
| 02/205818 DC : DRAFT JUN 2002 | EN 50370-1 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT FAMILY STANDARD FOR MACHINE TOOLS - PART 1: EMISSION |
| CSA IEC 61000-4-7 : 2013 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| CAN/CSA-IEC 61000-4-7:13 (R2017) | Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto (Adopted IEC 61000-4-7:2002, edition 2:2002 consolidated with amendment 1:2008) | Compatibilité électromagnétique (CEM) - Partie 4-7: Techniques d\'essai et de mesure - Guide général relatif aux mesures d\'harmoniques et d\'interharmoniques, ainsi qu\'à l\'appareillage de mesure, applicable aux réseaux d\'alimentation et aux appareils qui y sont raccordés (norme CEI 61000-4-7:2002 adoptée, édition 2:2002 consolidée par l\'amendement 1:2008) |
| IEEE 1901-2010 | IEEE Standard for Broadband over Power Line Networks: Medium Access Control and Physical Layer Specifications |
| DD IEC PAS 60044-5 : DRAFT SEP 2002 | INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS |
| CEI EN 60945 : 2003 | MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - GENERAL REQUIREMENTS - METHODS OF TESTING AND REQUIRED TEST RESULTS |
| BS EN 50147-2:1997 | Anechoic chambers Alternative test site suitability with respect to site attenuation |
| CEI EN 61284 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| CEI EN 61967-1 : 2002 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 1: GENERAL CONDITIONS AND DEFINITIONS |
| IEC 61334-3-1:1998 | Distribution automation using distribution line carrier systems - Part 3-1: Mains signalling requirements - Frequency bands and output levels |
| IEC TR 61131-4:2004 | Programmable controllers - Part 4: User guidelines |
| BS EN 55012 : 2007 | VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS |
| I.S. EN 60358-1:2012 | COUPLING CAPACITORS AND CAPACITOR DIVIDERS - PART 1: GENERAL RULES (IEC 60358-1:2012 (EQV)) |
| I.S. EN 60651:1994 | SOUND LEVEL METERS (IEC 60651:1979 (EQV)) |
| CSA CISPR 11 : 2004 : INC : AMD 2 : 2010 | INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) RADIO-FREQUENCY EQUIPMENT - ELECTROMAGNETIC DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| I.S. EN 50083-7:1999 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 7: SYSTEM PERFORMANCE |
| CSA CISPR 11 : 2004 | INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) RADIO-FREQUENCY EQUIPMENT - ELECTROMAGNETIC DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| BS EN 60315-9:1997 | Methods of measurement on radio receivers for various classes of emission Measurement of the characteristics relevant to radio data system (RDS) reception |
| TBR 028 : 20001 | SATELLITE EARTH STATIONS AND SYSTEMS (SES); VERY SMALL APERTURE TERMINAL (VSAT); TRANSMIT-ONLY, TRANSMIT/RECEIVE OR RECEIVE-ONLY SATELLITE EARTH STATIONS OPERATING IN THE 11/12/14 GHZ FREQUENCY BANDS |
| CSA C108.4 : 2006 | VEHICLES, BOATS, AND INTERNAL COMBUSTION ENGINE DRIVEN DEVICES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF RECEIVERS EXCEPT THOSE INSTALLED IN THE VEHICLE/BOAT/DEVICE ITSELF OR IN ADJACENT VEHICLES/BOATS/DEVICES |
| EN 61260:1995/A1:2001 | ELECTROACOUSTICS - OCTAVE-BAND AND FRACTIONAL-OCTAVE-BAND FILTERS |
| CISPR 16-2:2003 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2: Methods of measurement of disturbances and immunity |
| ISO 14982:1998 | Agricultural and forestry machinery Electromagnetic compatibility Test methods and acceptance criteria |
| I.S. EN 13309:2010 | CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY |
| I.S. EN ISO 14982:2009 | AGRICULTURAL AND FORESTRY MACHINERY - ELECTROMAGNETIC COMPATIBILITY - TEST METHODS AND ACCEPTANCE CRITERIA |
| DIN EN 61284 : 1998 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| VDE V 0115-121-5 : 1997 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: FIXED POWER SUPPLY INSTALLATIONS |
| VDE 0212-1 : 1998 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| VDE V 0115-121-4 : 1997 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| BS CISPR 16-4:2002 | Specification for radio disturbance and immunity measuring apparatus and methods Uncertainty in EMC measurements |
| NF EN 300385 : 2001 | |
| ETS 300 673 : 20001 | RADIO EQUIPMENT AND SYSTEMS (RES); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR 4/6 GHZ AND 11/12/14 GHZ VERY SMALL APERTURE TERMINAL (VSAT) EQUIPMENT AND 11/12/13/14 GHZ SATELLITE NEWS GATHERING (SNG) |
| 04/30112602 DC : DRAFT APR 2004 | IEC 62333-2 ED.1 - NOISE SUPPRESSION SHEET FOR DIGITAL DEVICES AND EQUIPMENT - PART 2: MEASURING METHODS |
| BS IEC 61334-3-1:1998 | Distribution automation using distribution line carrier systems. Mains signalling requirements Frequency bands and output levels |
| BS EN 60437:1998 | Radio interference test on high-voltage insulators |
| AECTP-500 : 2016 | ELECTROMAGNETIC ENVIRONMENTAL EFFECTS TESTS AND VERIFICATION |
| EN 302 262 : 1.1.1 DRAFT | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); PRODUCT FAMILY EMISSION STANDARD FOR WIRE-LINE TELECOMMUNICATION NETWORKS |
| CSA CEI/IEC 61000.4.7 : 2003(R2007) | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| CLC/TR 50427:2004 | Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation - Guide |
| R210-010 : 2002 | ELECTROMAGNETIC COMPATIBILITY - EMISSION MEASUREMENTS IN FULLY ANECHOIC CHAMBERS |
| TS 100 718 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - AVALANCHE BEACONS - TRANSMITTER-RECEIVER SYSTEMS |
| TR 102 215 : 1.3.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); RECOMMENDED APPROACH, AND POSSIBLE LIMITS FOR MEASUREMENT UNCERTAINTY FOR THE MEASUREMENT OF RADIATED ELECTROMAGNETIC FIELDS ABOVE 1 GHZ |
| TBR 043 : 20001 | SATELLITE EARTH STATIONS AND SYSTEMS (SES) - VERY SMALL APERTURE TERMINAL (VSAT) TRANSMIT-ONLY, TRANSMIT-AND-RECEIVE, RECEIVE-ONLY SATELLITE EARTH STATIONS OPERATING IN THE 4 GHZ AND 6 GHZ FREQUENCY BANDS |
| EG 202 290 : 1.1.1 FINAL DRAFT | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); MEASUREMENT UNCERTAINTIES AND TEST METHODOLOGIES FROM 1 GHZ TO 40 GHZ |
| 06/30157139 DC : 0 | |
| DIN V ENV 50121-5 : 1997 | BAHNANWENDUNGEN - ELEKTROMAGNETISCHE VERTRAEGLICHKEIT - ORTSFESTE BAHN-ENERGIEVERSORGUNGSANLAGEN |
| IEC 61851-22:2001 | Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station |
| 10/30218910 DC : 0 | BS ISO/IEC IEEE 8802-15-4 - INFORMATION TECHNOLOGY - TELECOMMUNICATIONS AND INFORMATION EXCHANGE BETWEEN SYSTEMS - LOCAL AND METROPOLITAN AREA NETWORKS - SPECIFIC REQUIREMENTS - PART 15-4: WIRELESS MEDIUM ACCESS CONTROL (MAC) AND PHYSICAL LAYER (PHY) SPECIFICATIONS FOR LOW-RATE WIRELESS PERSONAL AREA NETWORKS (WPANS) |
| 04/30122100 DC : DRAFT SEP 2004 | IEC 61587-3 - MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 - PART 3: ELECTROMAGNETIC SHIELDING PERFORMANCE TESTS FOR CABINETS, RACKS AND SUBRACKS |
| BS EN 50199:1996 | Electromagnetic compatibility (EMC). Product standard for arc welding equipment |
| TBR 027 : 20001 | SATELLITE EARTH STATIONS AND SYSTEMS (SES); LOW DATA RATE LAND MOBILE SATELLITE EARTH STATIONS (LMES) OPERATING IN THE 11/12/14 GHZ FREQUENCY BANDS |
| 96/208116 DC : 0 | PREN 50236 - ELECTROMAGNETIC COMPATIBILITY FOR POWER TRANSFORMERS |
| BS EN 60255-25:2000 | Electrical relays Electromagnetic emission tests for measuring relays and protection equipment |
| BS PD R210-010 : 2002 | ELECTROMAGNETIC COMPATIBILITY - EMISSION MEASUREMENTS IN FULLY ANECHOIC CHAMBERS |
| NF EN 301090 : 2001 | |
| TR 102 324 : 1.1.1 | POWERLINE TELECOMMUNICATIONS (PLT); RADIATED EMISSIONS' CHARACTERISTICS AND MEASUREMENT METHOD OF STATE OF THE ART POWERLINE COMMUNICATION NETWORKS |
| CSA CEI/IEC CISPR 13 : 2009 | SOUND AND TELEVISION BROADCAST RECEIVERS AND ASSOCIATED EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| CISPR 16-4:2002 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 4: Uncertainty in EMC measurements |
| NF EN 300279 : 2001 | |
| NF EN 50240 : 2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT STANDARD FOR RESISTANCE WELDING EQUIPMENT |
| I.S. EN 60315-9:1999 | METHODS OF MEASUREMENT ON RADIO RECEIVERS FOR VARIOUS CLASSES OF EMISSION - PART 9: MEASUREMENT OF THE CHARACTERISTICS RELEVANT TO RADIO DATA SYSTEM (RDS) RECEPTION |
| BS EN 60270 : 2001 | HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS |
| EN 302 536 : 2.1.1 | SHORT RANGE DEVICES (SRD); RADIO EQUIPMENT OPERATING IN THE FREQUENCY RANGE 315 KHZ TO 600 KHZ FOR ULTRA LOW POWER ANIMAL IMPLANTABLE DEVICES (ULP-AID) AND ASSOCIATED PERIPHERALS; HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF DIRECTIVE 2014/53/EU |
| I.S. EN 61326:1998 | |
| UNE-EN 301360 V1.1.3:2011 | Satellite Earth Stations and Systems (SES); Harmonized EN for Satellite Interactive Terminals (SIT) and Satellite User Terminals (SUT) transmitting towards geostationary satellites in the 27,5 GHz to 29,5 GHz frequency bands covering essential requirements under article 3.2 of the R&TTE Directive |
| VDE 0557-3 : 2001 COR 1 2004 | LOW-VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: PRODUCT EMC STANDARD |
| NF EN 61284 : 2000 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| CLC/TR 50627:2015 | Study Report on Electromagnetic Interference between Electrical Equipment/Systems in the Frequency Range Below 150 kHz |
| S.R. CLC/TR 50627:2015 | STUDY REPORT ON ELECTROMAGNETIC INTERFERENCE BETWEEN ELECTRICAL EQUIPMENT/SYSTEMS IN THE FREQUENCY RANGE BELOW 150 KHZ |
| IEC 60437:1997 | Radio interference test on high-voltage insulators |
| I.S. EN 60270:2001 | HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS |
| IEC 60315-9:1996 | Methods of measurement on radio receivers for various classes ofemission - Part 9: Measurement of the characteristics relevant toRadio Data System (RDS) reception |
| IEC 61967-5:2003 | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 5: Measurement of conducted emissions - Workbench Faraday Cage method |
| IEC 60044-5:2004 | Instrument transformers - Part 5: Capacitor voltage transformers |
| CISPR 12:2007+AMD1:2009 CSV | Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers |
| IEC 60255-25:2000 | Electrical relays - Part 25: Electromagnetic emission tests for measuring relays and protection equipment |
| EN 50199 : 95 AC 98 | |
| UNI EN 13309 : 2010 | CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY |
| UNI EN ISO 14982 : 2009 | AGRICULTURAL AND FORESTRY MACHINERY - ELECTROMAGNETIC COMPATIBILITY - TEST METHODS AND ACCEPTANCE CRITERIA |
| BS EN 60694:1997 | Common specifications for high-voltage switchgear and controlgear standards |
| 11/30242675 DC : 0 | BS EN 60099-4 F2 - SURGE ARRESTERS - PART 4: METAL-OXIDE SURGE ARRESTERS WITHOUT GAPS FOR A.C. SYSTEMS |
| TR 134 926 : 13.0.0 | UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); LTE; ELECTROMAGNETIC COMPATIBILITY (EMC); TABLE OF INTERNATIONAL REQUIREMENTS FOR MOBILE TERMINALS AND ANCILLARY EQUIPMENT (3GPP TR 34.926 VERSION 14.0.0 RELEASE 14) |
| NF ETS 300784 : 2000 | SATELLITE EARTH STATION AND SYSTEMS (SES) - TELEVISION RECEIVE-ONLY (TVRO) SATELLITE EARTH STATIONS OPERATING IN THE 11/12 GHZ FREQUENCY BANDS |
| NFC 91 016-2 : 2001 | SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY |
| BS EN 61000-4-7 : 2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| BS EN 61967-5:2003 | Integrated circuits. Measurement of electromagnetic emissions, 150 kHz to 1 GHz Measurement of conducted emissions. Workbench Faraday Cage method |
| BS 4054-9(1997) : 1997 | METHOD OF MEASUREMENT ON RADIO RECEIVERS FOR VARIOUS CLASSES OF EMISSION - PART 9: MEASUREMENT OF THE CHARACTERISTICS RELEVANT TO RADIO DATA SYSTEM (RDS) RECEPTION |
| PD CLC/TR 50627:2015 | Study Report on Electromagnetic Interference between Electrical Equipment/Systems in the Frequency Range Below 150 kHz |
| 08/30183914 DC : DRAFT JUNE 2008 | BS EN 60358-1 - COUPLING CAPACITORS AND CAPACITOR DIVIDERS - PART 1: COMMON CLAUSES |
| CEI 18-54 : 2003 | ELECTRICAL INSTALLATIONS IN SHIPS - PART 504: SPECIAL FEATURES - CONTROL AND INSTRUMENTATION |
| BS EN 50083-7 : 1997 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 7: SYSTEM PERFORMANCE |
| BS EN 61204-3:2001 | Low voltage power supplies, d.c. output Electromagnetic compatibility (EMC) |
| 99/201568 DC : DRAFT MAR 1999 | EN 50083-7:1996/PRA1:1999 - CABLED DISTRIBUTION SYSTEMS FOR TELEVISION AND SOUND SIGNALS - PART 7: SYSTEM PERFORMANCE |
| CEI R210-003 : 1997 | GUIDELINES ON HOW TO USE ANECHOIC ENCLOSURES THAT DO NOT FULFIL THE REQUIREMENTS REGARDING NORMALIZED SITE ATTENUATION FOR PRE-COMPLIANCE TESTS OF PRODUCTS |
| 02/204840 DC : DRAFT APR 2002 | PREN 50217 - IN SITU MEASUREMENTS OF DISTURBANCE EMISSION |
| NF ETS 300717 : 2000 | |
| TBR 030 : 20001 | SATELLITE EARTH STATIONS AND SYSTEMS (SES); SATELLITE NEWS GATHERING TRANSPORTABLE EARTH STATIONS (SNG TES) OPERATING IN THE 11-12/13-14 GHZ FREQUENCY BANDS |
| BS EN 50289-1-6:2002 | Communication cables. Specifications for test methods. Electrical test methods Electromagnetic performance |
| PD CLC/TR 50427:2004 | Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation. Guide |
| BS EN 61260:1996 | Electroacoustics. Octave-band and fractional-octave-band filters |
| NF EN 60437 : 2000 | RADIO INTERFERENCE TEST ON HIGH-VOLTAGE INSULATORS |
| EN 300 674-3-1 : 3.0.0 DRAFT | INTELLIGENT TRANSPORT SYSTEMS (ITS); ROAD TRANSPORT AND TRAFFIC TELEMATICS (RTTT); DEDICATED SHORT RANGE COMMUNICATIONS (DSRC); PART 3-1: TECHNICAL CHARACTERISTICS AND TEST METHODS FOR HIGH DATA RATE (HDR) DATA TRANSMISSION EQUIPMENT OPERATING IN THE 5,8 GHZ INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) BAND |
| BS EN 61326:1998 | Electrical equipment for measurement, control and laboratory use. EMC requirements |
| 05/30127980 DC : DRAFT JAN 2005 | ISO 13766 - EARTH-MOVING MACHINERY - ELECTROMAGNETIC COMPATIBILITY |
| TS 102 692 : 1.1.1 | ULTRA WIDEBAND (UWB); RF CONFORMANCE TESTING OF RADAR LEVEL GAUGING APPLICATIONS IN STILLPIPES TLPR |
| TBR 044 : 20001 | SATELLITE EARTH STATIONS AND SYSTEMS (SES) - LAND MOBILE EARTH STATIONS (LMES) OPERATING IN THE 1,5 GHZ AND 1,6 GHZ BANDS PROVIDING VOICE AND/OR DATA COMMUNICATIONS |
| TS 136 124 : 13.1.0 | LTE; EVOLVED UNIVERSAL TERRESTRIAL RADIO ACCESS (E-UTRA); ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS FOR MOBILE TERMINALS AND ANCILLARY EQUIPMENT (3GPP TS 36.124 VERSION 14.1.0 RELEASE 14) |
| CEI CLC/TR 50427 : 2005 | ASSESSMENT OF INADVERTENT IGNITION OF FLAMMABLE ATMOSPHERES BY RADIO-FREQUENCY RADIATION - GUIDE |
| IEEE C63.022-1996 | American National Standard for Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment |
| I.S. EN 50147-2:1999 | ANECHOIC CHAMBERS - PART 2: ALTERNATIVE TEST SITE SUITABILITY WITH RESPECT TO SITE ATTENUATION |
| ISO 14302:2002 | Space systems Electromagnetic compatibility requirements |
| I.S. EN 61967-1:2002 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 1: GENERAL CONDITIONS AND DEFINITIONS |
| CEI EN 61000-5-7 : 2003 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 5-7: INSTALLATION AND MITIGATION GUIDELINES - DEGREES OF PROTECTION BY ENCLOSURES AGAINST ELECTROMAGNETIC DISTURBANCES (EM CODE) |
| I.S. EN 61967-5:2003 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 5: MEASUREMENT OF CONDUCTED EMISSIONS - WORKBENCH FARADAY CAGE METHOD |
| ISO 19292:2014 | Ships and marine technology — Lifesaving and fire protection — Point-type resettable flame detectors for ships |
| NF EN 61967-4 : 2002 AMD 1 2006 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ - 1 GHZ - PART 4: MEASUREMENT OF CONDUCTED EMISSION - 1 OHM/150 OHM DIRECT COUPLING METHOD |
| I.S. EN 60255-25:2001 | ELECTRICAL RELAYS - PART 25: ELECTROMAGNETIC EMISSION TESTS FOR MEASURING RELAYS AND PROTECTION EQUIPMENT |
| I.S. EN 62333-2:2006 | NOISE SUPPRESSION SHEET FOR DIGITAL DEVICES AND EQUIPMENT - PART 2: MEASURING METHODS |
| EN 62333-2:2006/A1:2015 | NOISE SUPPRESSION SHEET FOR DIGITAL DEVICES AND EQUIPMENT - PART 2: MEASURING METHODS (IEC 62333-2:2006/A1:2015) |
| EN 60358-1:2012 | COUPLING CAPACITORS AND CAPACITOR DIVIDERS - PART 1: GENERAL RULES (IEC 60358-1:2012) |
| DIN EN ISO 14982:2009-12 | Agricultural and forestry machines - Electromagnetic compatibility - Test methods and acceptance criteria (ISO 14982:1998) |
| 00/246907 DC : DRAFT DEC 2000 | BS EN 61980-1 - ELECTRICAL - ELECTRIC VEHICLE INDUCTIVE CHARGING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| IEC 62333-2:2006+AMD1:2015 CSV | Noise suppression sheet for digital devices and equipment - Part 2:Measuring methods |
| IEC 60358-1:2012 | Coupling capacitors and capacitor dividers - Part 1: General rules |
| UNE-EN 50065-2-3:2004 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz -- Part 2-3: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 kHz to 95 kHz and intended for use by electricity suppliers and distributors |
| IEC 61967-1:2002 | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 1: General conditions and definitions |
| IEC 61000-4-7:2002+AMD1:2008 CSV | Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto |
| EN 300 674-2-1 : 1.1.1 | TRANSPORT AND TRAFFIC TELEMATICS (TTT); DEDICATED SHORT RANGE COMMUNICATION (DSRC) TRANSMISSION EQUIPMENT (500 KBIT/S/250 KBIT/S) OPERATING IN THE 5795 MHZ TO 5815 MHZ FREQUENCY BAND; PART 2: HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE DIRECTIVE 2014/53/EU; SUB-PART 1: ROAD SIDE UNITS (RSU) |
| EN ISO 14982:2009 | Agricultural and forestry machinery - Electromagnetic compatibility - Test methods and acceptance criteria (ISO 14982:1998) |
| IEC TS 61587-3:1999 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks |
| 04/30116608 DC : DRAFT JUL 2004 | EN 50121-5 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| BS EN 60945:2002 | Maritime navigation and radiocommunication equipment and systems. General requirements. Methods of testing and required test results |
| DIN V ENV 50121-3-2 : 1997 | BAHNANWENDUNGEN - ELEKTROMAGNETISCHE VERTRAEGLICHKEIT - SCHIENENFAHRZEUGE - GERAETE |
| BS EN 61284:1998 | Overhead lines. Requirements and tests for fittings |
| CEI EN 50289-1-6 : 2002 | COMMUNICATION CABLES SPECIFICATIONS FOR TEST METHODS - PART 1-6: ELECTRICAL TEST METHODS - ELECTROMAGNETIC PERFORMANCE |
| 03/311729 DC : DRAFT JULY 2003 | EN ISO 8041 - HUMAN RESPONSE TO VIBRATION - MEASURING INSTRUMENTATION |
| 09/30208590 DC : 0 | BS EN 61672-2 ED.2 - ELECTROACOUSTICS - SOUND LEVEL METERS - PART 2: PATTERN EVALUATION TESTS |
| CAN/CSA-CISPR 12-10 (R2018) | Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers (Adopted IEC CISPR 12:2007 + A1:2009, edition 6.1, 2009-03, with Canadian deviations) | Véhicules, bateaux et moteurs à combustion interne - Caractéristiques de perturbation radioélectrique - Limites et méthodes de mesure pour la protection des récepteurs extérieurs (norme IEC CISPR 12:2007 + A1:2009 adoptée, édition 6.1, 2009-03, avec exigences propres au Canada) |
| PD CLC/TR 50485:2010 | Electromagnetic compatibility. Emission measurements in fully anechoic chambers |
| I.S. EN 60942:2003 | ELECTROACOUSTICS - SOUND CALIBRATORS |
| EN 302 186 : 1.1.1 | SATELLITE EARTH STATIONS AND SYSTEMS (SES); HARMONISED STANDARD FOR SATELLITE MOBILE AIRCRAFT EARTH STATIONS (AESS) OPERATING IN THE 11/12/14 GHZ FREQUENCY BANDS COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE DIRECTIVE 2014/53/EU |
| BS EN 50065-7:2001 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz Equipment impedance |
| BIS IS 12193-3 : 2012(R2015) | METHODS OF MEASUREMENT ON RADIO RECEIVERS FOR VARIOUS CLASSES OF EMISSION - PART 3: RECEIVERS FOR FREQUENCY-MODULATED SOUND BROADCASTING EMISSIONS |
| PD 6591:1996 | Guidelines on how to use anechoic enclosures that do not fulfil the requirements regarding normalized site attenuation for pre-compliance tests of products |
| CEI CLC/TR 50485 : 2013 | ELECTROMAGNETIC COMPATIBILITY - EMISSION MEASUREMENTS IN FULLY ANECHOIC CHAMBERS |
| 00/243920 DC : DRAFT AUG 2000 | CISPR 20. ED. 5. SOUND AND TELEVISION BROADCAST RECEIVERS AND ASSOCIATED EQUIPMENT - IMMUNITY CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| ES 200 674-2 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - ROAD TRANSPORT AND TRAFFIC TELEMATICS (RTTT) - PART 2: TECHNICAL CHARACTERISTICS AND TEST METHODS FOR LOW DATA RATE (LDR) DATA TRANSMISSION EQUIPMENT OPERATING IN THE 5,8 GHZ INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) BAND |
| NF EN 60255-25 : 2001 | ELECTRICAL RELAYS - PART 25: ELECTROMAGNETIC EMISSION TESTS FOR MEASURING RELAYS AND PROTECTION EQUIPMENT |
| 00/560888 DC : APR 2000 | IEC 60601-1-2 EDITION 2 - MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR SAFETY - COLLATERAL STANDARD - ELECTROMAGNETIC COMPATIBILITY - REQUIREMENTS AND TESTS |
| 04/30117592 DC : DRAFT AUG 2004 | EN 50121-3-1 - RAILWAY APPLICATIONS. ELECTROMAGNETIC COMPATIBILITY - PART 3-1 - ROLLING STOCK. TRAIN AND COMPLETE VEHICLE |
| 09/30208585 DC : 0 | BS EN 61672-1 ED.2 - ELECTROACOUSTICS - SOUND LEVEL METERS - PART 1: SPECIFICATIONS |
| I.S. CLC TR 50427:2005 | ASSESSMENT OF INADVERTENT IGNITION OF FLAMMABLE ATMOSPHERES BY RADIO-FREQUENCY RADIATION - GUIDE |
| CSA E61131.2 :2006 | PROGRAMMABLE CONTROLLERS - PART 2: EQUIPMENT REQUIREMENTS AND TESTS |
| I.S. EN 55012:2007 | VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS |
| CEI EN 60315-4 : 1999 | METHODS OF MEASUREMENT ON RADIO RECEIVERS FOR VARIOUS CLASSES OF EMISSION - PART 4: RECEIVERS FOR FREQUENCY-MODULATED SOUND BROADCASTING EMISSIONS |
| 01/209170 DC : DRAFT DEC 2001 | IEC 62132-5 ED.1 - INTEGRATED CIRCUITS, MEASUREMENT OF ELECTROMAGNETIC IMMUNITY - PART 5: MEASUREMENT OF CONDUCTED IMMUNITY - WORKBENCH FARADAY CAGE METHOD |
| BS CISPR 12:1997 | Vehicles, motorboats and spark-ignited engine-driven devices. Radio disturbance characteristics. Limits and methods of measurement |
| ES 200 674-1 : 2.4.1 | INTELLIGENT TRANSPORT SYSTEMS (ITS); ROAD TRANSPORT AND TRAFFIC TELEMATICS (RTTT); DEDICATED SHORT RANGE COMMUNICATIONS (DSRC); PART 1: TECHNICAL CHARACTERISTICS AND TEST METHODS FOR HIGH DATA RATE (HDR) DATA TRANSMISSION EQUIPMENT OPERATING IN THE 5,8 GHZ INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) BAND |
| NF EN 301091 : 2001 | TELECOMMUNICATIONS - COMPATIBILITE ELECTROMAGNETIQUE ET SPECTRE RADIOELECTRIQUE (ERM) - TELEMATIQUE POUR LE TRANSPORT ET LE TRAFIC ROUTIER (RTTT) - CARACTERISTIQUES TECHNIQUES ET METHODES DE MESURE DES EQUIPEMENTS RADAR FONCTIONNANT DANS LA BANDE DE 76 GHZ A 77 GHZ |
| EN 300 132-3 : 1.2.1 | ENVIRONMENTAL ENGINEERING (EE); POWER SUPPLY INTERFACE AT THE INPUT TO TELECOMMUNICATIONS EQUIPMENT; PART 3: OPERATED BY RECTIFIED CURRENT SOURCE, ALTERNATING CURRENT SOURCE OR DIRECT CURRENT SOURCE UP TO 400 V |
| 04/300967 DC : DRAFT JAN 2004 | EN 50090-5-1 ED.1 - HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 5-1: MEDIA AND MEDIA DEPENDENT LAYERS - POWER LINE FOR HBES CLASS 1 |
| CSA E61131.2 : 2006 : R2016 | PROGRAMMABLE CONTROLLERS - PART 2: EQUIPMENT REQUIREMENTS AND TESTS |
| CSA CISPR 11 : 2004 : INC : AMD 2 : 2010 : R2013 | INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) RADIO-FREQUENCY EQUIPMENT - ELECTROMAGNETIC DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT |
| I.S. EN 61204-3:2000 | LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC) |
| CEI EN 50147-2 : 1998 | ANECHOIC CHAMBERS - PART 2: ALTERNATIVE TEST SITE SUITABILITY WITH RESPECT TO SITE ATTENUATION |
| NF EN 300339 : 2000 | |
| I.S. EN 61000-4-7:2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| I.S. EN 50065-7:2002 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 7: EQUIPMENT IMPEDANCE |
| IEC 60315-4:1997 | Methods of measurement on radio receivers for various classes of emission - Part 4: Receivers for frequency-modulated sound broadcasting emissions |
| I.S. EN 50240:2006 | |
| IEC PAS 60044-5:2002 | Instrument transformers - Part 5: Capacitor voltage transformers |
| EN 303 372-1 : 1.1.1 | SATELLITE EARTH STATIONS AND SYSTEMS (SES); SATELLITE BROADCAST RECEPTION EQUIPMENT; HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE DIRECTIVE 2014/53/EU; PART 1: OUTDOOR UNIT RECEIVING IN THE 10,7 GHZ TO 12,75 GHZ FREQUENCY BAND |
| EN 61800-3 : 2004 AMD 1 2012 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011) |
| DIN EN 13309:2010-12 | CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY |
| BS EN ISO 14982:2009 | Agricultural and forestry machinery. Electromagnetic compatibility. Test methods and acceptance criteria |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| BS EN 13309:2010 | Construction machinery. Electromagnetic compatibility of machines with internal power supply |
| EN 50065-2-2:2003/A1:2005/corrigendum Oct. 2006 | SIGNALING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-2: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 95 KHZ TO 148,5 KHZ AND INTENDED FOR USE IN INDUSTRIAL ENVIRONMENTS |
| EN 50065-7:2001 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 7: Equipment impedance |
| EN 61326:1997/A3:2003 | |
| EN 50370-1 : 2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| EN 50083-7 : 1996 COR 2007 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 7: SYSTEM PERFORMANCE |
| EN 50240:2004/corrigendum:2005 | |
| EN 60315-9:1996 | Methods of measurement on radio receivers for various classes of emission - Part 9: Measurement of the characteristics relevant to radio data system (RDS) reception |
| EN 61000-4-7:2002/A1:2009 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008) |
| EN 50289-1-6:2002 | Communication cables - Specifications for test methods - Part 1-6: Electrical test methods - Electromagnetic performance |
| EN 61204-3:2000 | Low voltage power supplies, d.c. output - Part 3: Electromagnetic compatibility (EMC) |
| CISPR 14-1:2016 | Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission |
| IEC 60315-3:1989+AMD1:1999 CSV | Methods of measurement on radio receivers for various classes of emission - Part 3: Receivers for amplitude-modulated sound-broadcasting emissions |
| CISPR 16-2:2003 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2: Methods of measurement of disturbances and immunity |
| IEC 60315-4:1997 | Methods of measurement on radio receivers for various classes of emission - Part 4: Receivers for frequency-modulated sound broadcasting emissions |
£497.21
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English - French
PDF - English - French
PDF 3 Users - English - French
PDF 5 Users - English - French
PDF 9 Users - English - French
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.