CAN/CSA-ISO/IEC 14165-115:2006(R2016)
Current
Current
The latest, up-to-date edition.
INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 115: PHYSICAL INTERFACES (FC-PI)
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
28-08-2016
Publisher
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions and conventions
4 Structure and concepts
5 FC-PI functional characteristics
6 Optical interface specification
7 Optical interface receptacle specifications
8 Optical fibre cable plant specification
9 Electrical cable interface specification
10 Electrical cable plant and connector specifications
Annex A (informative) - Test methods
Annex B (informative) - SERDES electrical interface example
Annex C (normative) - Optical cable plant usage
Annex D (normative) - Tx-Off and Rx-Loss of Signal detection
Bibliography
This part of ISO/IEC 14165 describes the physical interface portions of a high performance serial link that supports the higher Upper Level Protocols (ULPs) associated with HIPPI, IPI, SCSI, IP and others.
| Committee |
ISO/IEC JTC 1
|
| DocumentType |
Standard
|
| ISBN |
1-55436-359-4
|
| Pages |
118
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ISO/IEC 14165-115:2006 | Identical |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| ISO/IEC 14165-116:2005 | Information technology Fibre Channel Part 116: 10 Gigabit (10GFC) |
| IEC 61754-18:2001 | Fibre optic connector interfaces - Part 18: Type MT-RJ connector family |
| IEC 60807-3:1990 | Rectangular connectors for frequencies below 3 MHz - Part 3: Detail specification for a range of connectors with trapezoidal shaped metal shells and round contacts - Removable crimp contact types with closed crimp barrels, rear insertion/rear extraction |
| IEC 61280-1-3:2010 | Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Central wavelength and spectral width measurement |
| ISO/IEC 14165-141:2001 | Information technology Fibre Channel Part 141: Fabric Generic Requirements (FC-FG) |
| IEC 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| IEC 60793-1-41:2010 | Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth |
| IEC 60793-1-43:2015 | Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement |
| IEC 61300-2-25:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-25: Tests - Sealing endurance for closures |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| ISO/IEC 14165-133:2010 | Information technology Fibre Channel Part 133: Switch Fabric-3 (FC-SW-3) |
| IEC 61300-3-3:2009 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss |
| ISO/IEC 14165-222:2005 | Information technology Fibre Channel Part 222: Single-byte command code 2 mapping protocol (FC-SB-2) |
| ISO/IEC 11801:2002 | Information technology Generic cabling for customer premises |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61300-2-17:2010 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-17: Tests - Cold |
| IEC 60793-1-42:2013 | Optical fibres - Part 1-42: Measurement methods and test procedures - Chromatic dispersion |
| IEC 61300-2-5:2009 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion |
| ISO/IEC 14165-241:2005 | Information technology Fibre Channel Part 241: Backbone 2 (FC-BB-2) |
| ISO/IEC 14165-122:2005 | Information technology Fibre Channel Part 122: Arbitrated Loop-2 (FC-AL-2) |
| ISO/IEC 14165-414:2007 | Information technology Fibre Channel Part 414: Generic Services 4 (FC-GS-4) |
| ISO/IEC 14165-321:2009 | Information technology Fibre Channel Part 321: Audio-Video (FC-AV) |
| IEC 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| ISO/IEC 14165-131:2000 | Information technology Fibre Channel Part 131: Switch Fabric Requirements (FC-SW) |
| IEC 60793-1-40:2001 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| IEC 61280-4-1:2009 | Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement |
| IEC 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| IEC 61300-3-6:2008 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-6: Examinations and measurements - Return loss |
| IEC 61280-2-2:2012 | Fibre optic communication subsystem test procedures - Part 2-2: Digital systems - Optical eye pattern, waveform and extinction ratio measurement |
| IEC 61300-3-4:2012 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation |
| IEC 60169-8:1978 | Radio-frequency connectors. Part 8: R.F. coaxial connectors with inner diameter of outer conductor 6.5 mm (0.256 in) with bayonet lock - Characteristic impedance 50 ohms (Type BNC) |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 60793-1-20:2014 | Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry |
| IEC 61300-2-4:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention |
| ISO/IEC TR 14165-117:2007 | Information technology Fibre Channel Part 117: Methodologies for jitter and signal quality (MJSQ) |
| IEC 61754-6:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family |
| ISO/IEC 14165-211 : 1999(R2016) | INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 211: MAPPING TO HIPP-FP (FC-FP) |
| IEC 61754-20:2012 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family |
| IEC 61280-2-1:2010 | Fibre optic communication subsystem test procedures - Part 2-1: Digital systems - Receiver sensitivity and overload measurement |
| IEC 61754-4:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family |
| IEC 61754-1:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1: General and guidance |
| IEC 61300-2-6:2010 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism |
| ISO/IEC 14165-331:2007 | Information technology Fibre Channel Part 331: Virtual Interface (FC-VI) |
| ISO/IEC 14165-114:2005 | Information technology Fibre Channel Part 114: 100 MB/s Balanced copper physical interface (FC-100-DF-EL-S) |
| ISO/IEC 14165-251:2008 | Information technology Fibre Channel Part 251: Framing and Signaling (FC-FS) |
| IEC 61754-19:2001 | Fibre optic connector interfaces - Part 19: Type SG connector family |
| IEC 61076-3-103:2003 | Connectors for electronic equipment - Part 3-103: Rectangular connectors - Detail specification for single row connectors with non-removable ribbon cable contacts on 1,25 mm pitch used for high speed serial data (HSSDC) |
| IEC 61300-3-11:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-11: Examinations and measurements - Engagement and separation forces |
£170.98
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.