DEFSTAN 02-179/1(2002) : 2002

Name: DEFSTAN 02-179/1(2002) : 2002
Brand: DEFSTAN

Withdrawn

REQUIREMENTS FOR LOCKERS (MAGAZINE, RU MAGAZINE AND DETONATOR) USED FOR STORAGE OF EXPLOSIVE STORES IN HM SURFACE SHIPS AND SUBMARINES

Withdrawn date

23-08-2019

Published date

12-01-2013

Publisher

UK Ministry of Defence Standards

SCOPE
FOREWORD
Sponsorship
Conditions of Release
Categories of Naval Defence Standard
Related Documents
Health and Safety
Additional Information
CONTENTS
SECTION 1 - PERFORMANCE SPECIFICATION
            1.1 General
            1.2 Environmental Conditions
SECTION 2 - NATIONAL/INTERNATIONAL REGULATIONS
SECTION 3 - MILITARY STANDARDS/REQUIREMENTS
            3.1 General Requirements
                3.1.1 Distortion/Racking (due to flooding)
                3.1.2 Base/Legs
                3.1.3 Shock (Non-Contact Underwater Explosion)
                3.1.4 Electrical Screening
                3.1.5 Response to Attack on Ammunition
                3.1.6 Insulation/Cladding Plates
                3.1.7 Radar Cross Section (Radar Echo Area)
                3.1.8 Radar Absorbent Material
                3.1.9 Welding
                3.1.10 Galvanizing
                3.1.11 Painting
                       3.1.11.1 Surface Coatings for Detonator
                                Lockers only
                       3.1.11.2 External Coatings
                       3.1.11.3 Internal Coatings
                3.1.12 Locker Doors and Lids
                       3.1.12.1 Door Seals
                       3.1.12.2 Hinges
                       3.1.12.3 Locking Arrangements
                       3.1.12.4 Clips and Closing Arrangements
                3.1.13 Flooding Connection
                3.1.14 Drainage Arrangements
                3.1.15 Venting
                3.1.16 Configuration
                3.1.17 Interchangeability
                3.1.18 Stowage Arrangements
                3.1.19 Identification
                3.1.20 Representative Inert Rounds/Ammunition
                       Boxes
                3.1.21 Fittings
                3.1.22 Maximum/Minimum Thermometer Bracket
                3.1.23 Temperature Card Holder
                3.1.24 Magazine Designed Capacity List - S285K
                3.1.25 Notice board
                3.1.26 Tally/Marker Plates
                3.1.27 Warning Notices
                3.1.28 Detonator Lockers
                       3.1.28.1 Deck Mounted
                       3.1.28.2 Bulkhead Mounted
            3.2 Test and Trials
SECTION 4 - DESIGN REQUIREMENTS/GUIDANCE
            4.1 Construction
            4.2 Material
            4.3 Composite Material
                4.3.1 General Construction
                4.3.2 Locker Carcass
                4.3.3 Locker Coatings
SECTION 5 - CORPORATE EXPERIENCE & KNOWLEDGE
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS AND DEFINITIONS
ANNEX C - PROCUREMENT CHECK LIST
ANNEX D - CHECK LIST FOR A NEW/REFURBISHED MAGAZINE LOCKER OR
          READY-USE MAGAZINE LOCKER
ANNEX E - CURRENT RANGE OF AMMUNITION AND DETONATOR LOCKERS
ALPHABETICAL INDEX

Describes the specific requirements for the design, production and fitting out of Magazine, Detonator and Ready-use Magazine Lockers.

DevelopmentNote	Supersedes DEFSTAN 08-146/1(2001). (06/2002) This standard is obsolescent because it is no longer required for the procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (04/2012)
DocumentType	Standard
PublisherName	UK Ministry of Defence Standards
Status	Withdrawn
Supersedes	DEFSTAN 08-146/1(2001) : 2001

DEFSTAN 00-101(PT1)/2(2008) : 2008

DESIGN STANDARDS FOR EXPLOSIVES SAFETY IN MOD SHIPS AND SUBMARINES - PART 1: SURFACE SHIPS

BS 381C:1996	Specification for colours for identification, coding and special purposes
DEFSTAN 80-125/2(1999) : 1999	PAINT, FINISHING, EMULSION, FOR CANVAS, BRUSHING
BS EN 12167:2011	Copper and copper alloys. Profiles and bars for general purposes
DEFSTAN 08-123/1(2000) : 2000	REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2
DEFSTAN 02-758/1(2000) : 2000	REQUIREMENTS FOR WEATHERWORK PREPARATION AND PAINTING OF SURFACE SHIPS
DEFSTAN 80-165/1(1993) : INTERIM	PAINT SYSTEM FOR SHIP'S WEATHERWORK, HIGH DURABILITY, LIGHT WEATHERWORK GREY - TYPE: BRUSHING
DEFSTAN 02-723/1(2000) : 2000	REQUIREMENTS FOR MARKER PLATES
DEFSTAN 80-78/2(1995) : 1995	PAINT, FINISHING, FLAME RETARDANT, BRUSHING
DEFSTAN 02-706/1(2000) : 2000	WELDING AND FABRICATION OF SHIP'S STRUCTURE
DEFSTAN 08-101(PT2)/1(2000) : 2000	REQUIREMENTS FOR THE CONSTRUCTION AND SYSTEM ARRANGEMENTS IN MAGAZINES AND WEAPON STORAGE COMPARTMENTS - CATEGORY 1 - PART 2: HM SUBMARINES
BS EN ISO 1461:2009	Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods
DEFSTAN 02-759/1(2000) : 2000	USE OF PRE-TREATMENT PRIMER CATEGORY 3
DEFSTAN 02-167/1(2000) : 2000	REQUIREMENTS FOR RESIN POLYESTER FOR SHIP STRUCTURES
DEFSTAN 80-187/1(1993) : INTERIM	PAINT SYSTEM FOR SHIPS' WEATHERWORK - PAINT PRIMING, SHIPS' - WEATHERWORK - PAINT UNDERCOAT, SHIPS' WEATHERWORK - PAINT FINISHING, SHIPS' WEATHERWORK - TYPE: BRUSHING
DEFSTAN 08-101(PT1)/1(2000) : 2000	REQUIREMENTS FOR THE CONSTRUCTION AND SYSTEM ARRANGEMENTS IN MAGAZINES AND WEAPON STORAGE COMPARTMENTS - CATEGORY 1 - PART 1: HM SURFACE SHIPS
DEFSTAN 02-154/1(2000) : 2000	DESIGN STANDARDS FOR SURFACE SHIP STRUCTURES
BS EN 12163:2011	Copper and copper alloys. Rod for general purposes
BS EN 12164:2011	Copper and copper alloys. Rod for free machining purposes