DIN 18515-1:1998-08

Superseded

CLADDING FOR EXTERNAL WALLS - PART 1: TILES FIXED WITH MORTAR - PRINCIPLES OF DESIGN AND APPLICATION

Available format(s)

Hardcopy , PDF

Superseded date

07-03-2021

Language(s)

English

Published date

01-01-1998

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

Foreword
1 Scope and field of application
2 Normative references
3 Concepts
4 Materials
5 Requirements for external walls
6 Claddings fixed to walls without external
thermal insulation
7 Claddings fixed to walls with external
Thermal insulation

Specifies requirements for the installation and design of cladding that comprises tiles or (cast or natural) stone units having a side length no greater than 0,40 m, a thickness no greater than 0,015 m, and an area not exceeding 0,12 m[2] (fluted tiles may be up to 0,02 m thick, including flutes). Also applies to cladding units having a thickness greater than 0,015 m and up to 0,03 m if their mass is not greater than 1,5 kg unit and their bond area is at least 100 cm[2].

DevelopmentNote	Suspended until publication of a revised English text, due to a new German edition. (05/2015)
DocumentType	Standard
Pages	6
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Superseded

DIN 18540:2014-09	SEALING OF EXTERIOR WALL JOINTS IN BUILDING USING JOINT SEALANTS
DIN 1053-1:1996-11	MASONRY - PART 1: DESIGN AND CONSTRUCTION
DIN 17441:1997-02	STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR COLD ROLLED STRIPS AND SLIT COILS STRIP AND SHEETS CUT FROM SUCH STRIPS FOR PRESSURE PURPOSES
DIN 1045 : 1988 AMD 1 1996	STRUCTURAL USE OF CONCRETE - DESIGN AND CONSTRUCTION
DIN 4226-1:2001-07	AGGREGATES FOR CONCRETE AND MORTAR - PART 1: NORMAL AND HEAVY-WEIGHT AGGREGATES
DIN 18550-2:2015-06	DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: SUPPLEMENTARY PROVISIONS FOR DIN EN 13914-2:2016-09 FOR INTERNAL PLASTERING
DIN 18516-1:2010-06	Cladding for external walls, ventilated at rear - Part 1: Requirements, principles of testing
DIN EN 1322:1999-03	ADHESIVES FOR TILES - DEFINITIONS AND TERMINOLOGY
DIN 1053-2:1996-11	MASONRY - PART 2: MASONRY STRENGTH CLASSES ON THE BASIS OF SUITABILITY TESTS
DIN 18156-2:1978-03	MATERIALS FOR CERAMIC LININGS BY THIN MORTAR BED TECHNIQUE - HYDRAULIC MORTAR
DIN 66133:1993-06	DETERMINATION OF PORE VOLUME DISTRIBUTION AND SPECIFIC SURFACE AREA OF SOLIDS BY MERCURY INTRUSION
DIN 18164-1:1992-08	RIGID CELLULAR PLASTICS INSULATING BUILDING MATERIALS - THERMAL INSULATING MATERIALS
DIN 18157-1:2016-01 (Draft)	EXECUTION OF TILINGS AND COVERINGS BY THIN MORTAR BED TECHNIQUE - PART 1: CEMENT-BASED MORTARS
DIN EN 187-1:1991-12	EXTRUDED CERAMIC TILES WITH A WATER ABSORPTION OF 6% < E = 10% (GROUP A2B)
DIN EN 187-2:1991-12	EXTRUDED CERAMIC TILES WITH A WATER ABSORPTION OF 6% < E = 10% (GROUP A2B)
DIN 18516-3:2013-09	CLADDING FOR EXTERNAL WALLS, VENTILATED AT REAR - PART 3: NATURAL STONE - REQUIREMENTS, DESIGN
DIN 105-1:1989-08	CLAY BRICKS - SOLID BRICKS AND VERTICALLY PERFORATED BRICKS
DIN 18500:1991-04	CAST STONES - TERMINOLOGY, REQUIREMENTS, TESTING, INSPECTION
DIN 1164-1 : 1994 AMD 1 1999	CEMENT - PART 1: COMPOSITION, SPECIFICATIONS
DIN 17440:2001-03	STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR DRAWN WIRE
DIN 4108-3:2014-11	THERMAL PROTECTION AND ENERGY ECONOMY IN BUILDINGS - PART 3: PROTECTION AGAINST MOISTURE SUBJECT TO CLIMATE CONDITIONS - REQUIREMENTS AND DIRECTIONS FOR DESIGN AND CONSTRUCTION