• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN EN 483:2000-06

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW
Available format(s)

Hardcopy , PDF

Superseded date

01-01-2013

Language(s)

English

Published date

01-01-2000

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of boilers
5 Constructional requirements
6 Operational requirements
7 Test methods
8 Marking and instructions
Annex A (informative) - National situations
Annex B (informative) - Particular national conditions
Annex C (informative) - Classification of Type C boilers
Annex D (informative) - Composition of the gas circuit
Annex E (informative) - Compilation of the test conditions
Annex F (normative) - Test apparatus for Type C[2] boilers
Annex G (informative) - Practical method of calibrating the
        test rig to enable the heat loss D[p] to be determined
Annex H (informative) - A-deviations
Annex J (informative) - Main symbols and abbreviations used
Annex K (informative) - Examples for marking
Annex L (informative) - Example of calculation of the
        weighting factors for a boiler with several rates
        following Table 17
Annex M (informative) - Calculation of conversions of NO[x]
Annex N (informative) - Requirements and test methods for
        separate air supply and combustion products evacuation
        ducts of Type C[6] boilers
Annex P (informative) - Determination of the heat loses from
        the test rig of the indirect method and the
        contribution of the circulating pump of the test rigs
Annex Q (informative) - Means of determining the ignition time at
        full rate
Annex ZA (informative) - Clauses of this European standard
         addressing essential requirements or other provisions
         of EU Directives
Annex R (normative) - Test methods to determine the effects of
        to long-term thermal load, long-term condensate exposure,
        condensing/non-condensing cycling and resistance to
        UV radiation
Annex S (informative) - Comparison table on clauses of this
        amendment addressing essential requirements of the
        GAD or other provisions of EU directives
Bibliography

DevelopmentNote
Supersedes DIN 3368-5 E and DIN 3368-6 E. (03/2003)
DocumentType
Standard
Pages
138
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

EN 1859:2009+A1:2013 Chimneys - Metal chimneys - Test methods
EN ISO 1183-3 : 1999 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 3: GAS PYKNOMETER METHOD
EN ISO 8256:2004 Plastics - Determination of tensile-impact strength (ISO 8256:2004)
EN 1856-2:2009 Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN 13216-1:2004 Chimneys - Test methods for system chimneys - Part 1: General test methods
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 8256:2004 Plastics — Determination of tensile-impact strength
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
EN 14241-1:2013 Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners
ISO 7619:1997 Rubber Determination of indentation hardness by means of pocket hardness meters
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
ISO 6914:2013 Rubber, vulcanized or thermoplastic Determination of ageing characteristics by measurement of stress relaxation in tension
EN 14471:2013+A1:2015 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
EN 1856-1:2009 Chimneys - Requirements for metal chimneys - Part 1: System chimney products
ISO 178:2010 Plastics Determination of flexural properties
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
EN 513:1999 Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
ISO 2781:2008 Rubber, vulcanized or thermoplastic Determination of density

View more information
£199.54
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.