• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN EN ISO 11296-3:2011-07

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES
Available format(s)

Hardcopy , PDF

Superseded date

01-05-2019

Language(s)

German, English

Published date

01-01-2011

National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings
7 Ancillary components
8 Fitness for purpose of the installed lining system
  at the 'I' stage
9 Installation practice
Annex A (normative) - Factory folded heat reverted
        polyethylene (PE) pipe - Determination of
        memory ability
Annex B (normative) - Folded polyethylene (PE) pipe -
        Determination of resistance to circumferential
        tensile stress at constant temperature
Bibliography

This standard is included in DIN Handbook 13-4.

DevelopmentNote
Supersedes DIN EN 13566-3. (07/2011) DRAFT 2017 issued in September 2017. (09/2017)
DocumentType
Standard
Pages
28
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 11296-3:2018 Identical
EN ISO 11296-3:2011 Identical
ISO 11296-3:2009 Identical

DIN HDBK 13-4 : 10ED 2015 ABWASSERTECHNIK 4 - ABWASSERKANAELE, ABWASSERLEITUNGEN - PLANUNG, VERLEGUNG, BETRIEB, SANIERUNG

DIN EN ISO 9967:2016-07 THERMOPLASTICS PIPES - DETERMINATION OF CREEP RATIO (ISO 9967:2016)
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
DIN EN ISO 6259-1:2015-08 THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL TEST METHOD (ISO 6259-1:2015)
ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
ISO 2507-1:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
DIN EN ISO 11295:2016-08 (Draft) CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION
ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
DIN EN ISO 11296-1:2011-07 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL
ISO 18373-1:2007 Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature
DIN EN ISO 9969:2016-06 THERMOPLASTICS PIPES - DETERMINATION OF RING STIFFNESS (ISO 9969:2016)
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 21138-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method

View more information
£84.76
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.