Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
DIN
DIN EN ISO 14405-2:2012-03

DIN EN ISO 14405-2:2012-03

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011)

Available format(s)

Hardcopy , PDF

Superseded date

01-06-2019

Language(s)

German, English

Published date

01-01-2012

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and rules for indication of dimensions
  and related tolerances
5 Units used in drawings for dimensions
6 Indication of tolerances for linear and angular dimensions
7 Illustrations of ambiguous +/- tolerancing vs. unambiguous
  geometrical tolerancing
8 Angular tolerancing
Annex A (informative) - Explanations and examples of the
        ambiguity caused by using +/- tolerances for dimensions
        other than linear size
Annex B (informative) - Relation to the GPS matrix model
Bibliography

Provides the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.

DevelopmentNote
DRAFT AMD 1 issued in July 2017. (07/2017)
DocumentType
Standard
Pages
31
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy

Standards Relationship
EN ISO 14405-2:2011 Identical
ISO 14405-2:2011 Identical

DIN EN ISO 2538-2:2015-01 Geometrical product specifications (GPS) - Wedges - Part 2: Dimensioning and tolerancing (ISO 2538-2:2014)
DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
DIN EN ISO 14405-3:2013-08 (Draft) GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 3: ANGULAR SIZES (ISO 14405-3:2016)
DIN 16742:2013-10 PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS
DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
DIN EN ISO 10451:2010-11 Dentistry - Contents of technical file for dental implant systems (ISO 10451:2010)

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
DIN EN ISO 286-1:2010-11 GEOMETRICAL PRODUCT SPECIFICATION (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS
DIN EN ISO 14660-1:1999-11 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRIC FEATURES - PART 1: GENERAL TERMS AND DEFINITIONS
ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
DIN EN ISO 8015:2011-09 Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules (ISO 8015:2011)
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
ISO 3040:2016 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
ISO 81714-1:2010 Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules
DIN EN ISO 17450-2:2013-04 Geometrical product specifications (GPS) - General concepts - Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities (ISO 17450-2:2012)
ISO 2538:1998 Geometrical Product Specifications (GPS) Series of angles and slopes on prisms
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
DIN EN ISO 17450-1:2012-04 Geometrical product specifications (GPS) - General concepts - Part 1: Model for geometrical specification and verification (ISO 17450-1:2011)
ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces
DIN EN ISO 14405-1:2017-07 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 1: LINEAR SIZES (ISO 14405-1:2016)

View more information
£78.51
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - German
PDF - German
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us