• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13433:2006

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Devices to prevent pollution by backflow of potable water - Mechanical disconnector, direct actuated - Family G, type A
Superseded date

14-01-2022

Published date

01-03-2006

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Nominal size
5 Designation
6 Symbolization
7 Physico-chemical characteristics
   7.1 Materials
   7.2 Nature of the materials
8 Design
   8.1 General
   8.2 Relief valve
   8.3 Disconnection distance
9 Characteristics and tests
   9.1 General
   9.2 General tolerances
   9.3 Expression of the results
   9.4 Dimensional characteristics
   9.5 Mechanical characteristics
   9.6 Leaktightness characteristics
   9.7 Hydraulic characteristics
10 Order of testing
11 Marking and technical documents
   11.1 General
   11.2 Marking
   11.3 Technical documents
12 Presentation at delivery
Annex A (informative) Examples of presentation of test results
Bibliography

This European Standard specifies, the dimensional, the physico-chemical, the design, the hydraulic, the mechanical and the acoustic characteristics of mechanical disconnector, direct actuated Family G, type A.This European Standard is applicable to mechanical disconnector direct actuated in nominal sizes DN 8 up to DN 250 included, intended to prevent the return of water having lost its original sanitary and drinking qualities (called "polluted water" in this European Standard), into the potable water distribution system whenever the pressure of the latter is temporarily lower than in the polluted circuit.This European Standard covers the mechanical disconnector direct actuated of PN 10 that are capable of working without modification or adjustment:-at any pressure up to 1 MPa (10 bar);-with any pressure variation up to 1 MPa (10 bar);-in permanent duty at a limit temperature of 65 °C and 90 °C for 1 h maximum.It specifies also the test methods and requirements for verifying these characteristics, the marking and the presentation at delivery.

Committee
CEN/TC 164
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
UNI EN 13433 : 2006 Identical
PN EN 13433 : 2006 Identical
BS EN 13433:2007 Identical
UNE-EN 13433:2006 Identical
SN EN 13433 : 2006 Identical
NS EN 13433 : 1ED 2006 Identical
DIN EN 13433:2006-05 Identical
I.S. EN 13433:2006 Identical
NEN EN 13433 : 2006 Identical
NF EN 13433 : 2006 Identical
NBN EN 13433 : 2006 Identical

NF EN 806-5 : 2012 SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE
DIN EN 806-5:2012-04 Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance
BS EN 806-5:2012 Specifications for installations inside buildings conveying water for human consumption Operation and maintenance
09/30200073 DC : 0 BS EN 806-5 - SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE
EN 806-5:2012 Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance
UNI EN 806-5 : 2012 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE
I.S. EN 806-5:2012 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE
UNE-EN 806-5:2013 Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
EN 806-1:2000/A1:2001 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 1: GENERAL
EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
ISO 6509:1981 Corrosion of metals and alloys Determination of dezincification resistance of brass
EN 13959:2004 Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 3822-3:1997 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 3: Mounting and operating conditions for in-line valves and appliances
EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
EN ISO 6509 : 1995 CORROSION OF METALS AND ALLOYS - DETERMINATION OF DEZINCIFICATION RESISTANCE OF BRASS
EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
EN 1267:2012 Industrial valves - Test of flow resistance using water as test fluid
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.