• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 140000 : 1993

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GENERIC SPECIFICATION: FIXED RESISTORS
Superseded date

01-09-2001

Published date

12-01-2013

Cooperating organizations
National foreword
Foreword
Section one. Scope
1. Scope
Section two. General
2. General
2.1 Related documents
2.2 Units, symbols and terminology
2.3 Preferred values
2.4 Marking
2.5 ESD sensitivity
Section three. Quality assessment procedures
3. Quality assessment procedures
3.1 General
3.2 Primary stage of manufacture
3.3 Subcontracting
3.4 Structurally similar components
3.5 Qualification approval procedures
3.6 Capability approval procedures
3.7 Rework and repair work
3.8 Release for delivery
3.9 Certified test records
3.10 Delayed delivery
3.11 Alternative test methods
3.12 Assessed process average procedures
3.13 Manufacture outside the geographical limits of CECC
      supervising inspectorates
Section four. Test and measurement procedures
4. Test and measurement procedures
4.1 General
4.2 Standard atmospheric conditions
4.3 Drying
4.4 Visual examination and check of dimensions
4.5 Resistance
4.6 Insulation resistance
4.7 Voltage proof
4.8 Variation of resistance with temperature
4.9 Reactance
4.10 Non-linear properties
4.11 Voltage coefficient
4.12 Noise
4.13 Overload
4.14 Temperature rise
4.15 Robustness of the resistor body
4.16 Robustness of terminations
4.17 Solderability
4.18 Resistance to soldering heat
4.19 Rapid change of temperature
4.20 Bump
4.21 Shock
4.22 Vibration
4.23 Climatic sequence
4.24 Damp heat, steady state
4.25 Endurance
4.26 Accidental overload test (for lower power
      non-wirewound resistors only)
4.27 Single-pulse high-voltage overload test
4.28 Periodic pulse high-voltage overload test
4.29 Component solvent resistance
4.30 Solvent resistance of marking
4.31 Shear test and substrate bending test (for surface
      mounting resistors only)
4.32 Corrosion
4.33 Flammability
4.34 Seal test (Hermetically sealed resistors only)
Annexes
A. Example of a certified test record (RCE)
B. Internal visual examination of fixed resistors
C. External visual examination of fixed resistors
      with enhanced assessment of quality
D. Radiographic inspection of fixed resistors
E. Blank detail specifications
National annex NA (informative) Committees responsible
National annex NB (informative) Cross-references

Relates to fixed discrete resistors with the exception of those whose prime use requires that resistance is temperature or voltage dependent. Coverage includes: quality assessment procedures, assessed process average procedures, standard atmospheric conditions, temperature rise, voltage coefficient, and insulation resistance. Also gives detailed annexes.

Committee
TC 40XA
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

Standards Relationship
BS EN 140000:1995 Identical
I.S. EN 140000:1994 Identical
DIN EN 140000:1994-10 Identical
NEN EN 140000 : 1997 Identical
SN EN 140000 : 1992 Identical
UNE-EN 140000:1993 Identical

BS EN 140200:1997 Harmonized system of quality assessment for electronic components. Sectional specification: fixed power resistors
BS EN 140202:1997 Harmonized system of quality assessment for electronic components. Blank detail specification: fixed power resistors (Assessment level M)
EN 133000:1997 Generic Specification: Passive filter units for electromagnetic interference suppression
BS EN 133000:1997 Harmonized system of quality assessment for electronic components. Generic specification: passive filter units for electromagnetic interference suppression
I.S. EN 133000:1998 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (GENERIC SPECIFICATION)
EN 140200 : 1996 AMD 1 2001 FIXED POWER RESISTORS (SECTIONAL SPECIFICATION)
BS EN 140203:1997 Harmonized system of quality assessment for electronic components. Blank detail specification: fixed power resistors (Assessment level H)
BS EN 140201:1997 Harmonized system of quality assessment for electronic components. Blank detail specification: fixed power resistors (Assessment level S)
I.S. EN 140210:1994 FIXED POWER RESISTORS - CAPABILITY APPROVAL (SECTIONAL SPECIFICATION)
I.S. CECC 33000:1994 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (GENERIC SPECIFICATION)

CECC 00109 : 1974 CECC RULES OF PROCEDURE: RP 9: CERTIFIED TESTS RECORDS
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
CECC 00006 : 1981 BASIC SPECIFICATION: ENVIRONMENTAL TEST PROCEDURES
IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
CECC 00100 : 1988 BASIC RULES - TO BE USED IN CONNECTION WITH THE INTERNAL REGULATIONS OF THE FEN e.V
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
ISO 3:1973 Preferred numbers Series of preferred numbers
CECC 00015 : 91 ERRATA BASIC SPECIFICATION - PROTECTION OF ELECTROSTATIC SENSITIVE DEVICES - GENERAL REQUIREMENTS
CECC 00114 : 93 AMD 1 QUALITY ASSESSMENT PROCEDURES - APPROVAL OF MANUFACTURERS AND OTHER ORGANIZATIONS
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
IEC 60068-2-3:1969 Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC TR 60440:1973 Method of measurement of non-linearity in resistors
IEC 60062:2016 Marking codes for resistors and capacitors
IEC 60068-2-2a:1976 Supplement A - Basic environmental testing procedures - Part 2: Tests - Tests B: Dry heat
CECC 00111 : 80 AMD 3 CECC RULES OF PROCEDURE: RP 11: SPECIFICATIONS AND THEIR HARMONIZATION - COMPONENTS FOR GENERAL AND PROFESSIONAL USAGE - COMPONENTS OF ENHANCED ASSESSMENT OF QUALITY
IEC 60063:2015 Preferred number series for resistors and capacitors
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
IEC 60068-2-29:1987 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
CECC 00007 : 1978 BASIC SPECIFICATION: SAMPLING PLANS AND PROCEDURES FOR INSPECTION BY ATTRIBUTES
IEC 60068-2-1A:1976 Supplement A - Basic environmental testing procedures - Part 2-1: Tests - Tests A: Cold
IEC 60195:2016 Method of measurement of current noise generated in fixed resistors
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.