• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 14304:2015

Current
Current

The latest, up-to-date edition.

Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification
Published date

09-12-2015

European foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols, units and abbreviated terms
4 Requirements
5 Test methods
6 Designation code
7 Assessment and Verification of the Constancy of
  Performance (AVCP)
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (normative) - Determination of minimum service
        temperature
Annex C (normative) - Thermal conductivity measurement
Annex D (informative) - Additional properties
Annex ZA (informative) - Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Regulation
Bibliography

This European Standard specifies the requirements for factory made flexible elastomeric foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 200 °C to + 175 °C.Below an operating temperature of - 50 °C, tests regarding the suitability of the products in the intended application should be performed. Manufacturer's advice should be heeded in all cases.The products are manufactured in the form of sheets, tubes, rolls and tapes with or without coating and/or self-adhesive backing and/or different closure systems.This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.Products with a declared thermal conductivity greater than 0,050 W/(m·K) at 10 °C are not covered by this standard.This European Standard does not cover products for the insulation of the building structure.The normative part of this European Standard does not cover compressive stress (see D.5).

Committee
CEN/TC 88
DevelopmentNote
Supersedes PREN 14304. (01/2016)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
SS-EN 14304:2015 Identical
NEN EN 14304 : 2016 Identical
UNE-EN 14304:2017 Identical
BS EN 14304 : 2009 Identical
DIN EN 14304:2016-03 Identical
PN EN 14304 : 2016 Identical
UNI EN 14304 : 2013 Identical
I.S. EN 14304:2015 Identical
NF EN 14304 : 2016 Identical
UNI EN 14304:2016 Identical
DIN EN 14304 E : 2016 Identical
SN EN 14304 : 2015 Identical
NBN EN 14304 : 2016 Identical
NS EN 14304 : 2015 Identical
BS EN 14304:2015 Identical

07/30167661 DC : DRAFT AUG 2007 BS EN 15715 - THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
UNE-EN 16783:2017 Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
UNI EN 15715 : 2009 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
VDI 2055 Blatt 2:2013-10 Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials
14/30301580 DC : 0 BS EN/TC 16783 - THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS
DIN EN 15715:2010-04 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
I.S. EN 16783:2017 THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS
I.S. EN 15715:2009 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
UNE-EN 15715:2012 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
EN 16783:2017 Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
EN 15715:2009 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
BS EN 16783:2017 Thermal insulation products. Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
BS EN 15715:2009 Thermal insulation products. Instructions for mounting and fixing for reaction to fire testing. Factory made products
DIN EN 15715 E : 2010 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
ISO 9229:2007 Thermal insulation Vocabulary
EN 12667:2001 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance
ISO 13787:2003 Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity
EN 14706:2012 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature
EN 12085:2013 Thermal insulating products for building applications - Determination of linear dimensions of test specimens
VDI 2055 Blatt 2:2013-10 Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials
EN 13468:2001 Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH
EN ISO 10456:2007/AC:2009 BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES
ISO 354:2003 Acoustics — Measurement of sound absorption in a reverberation room
EN 12939:2000 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance
EN ISO 8497:1996 Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994)
EN ISO 9229:2007 Thermal insulation - Vocabulary (ISO 9229:2007)
305/2011 : 2011 AMD 2 2014 REGULATION (EU) NO 305/2011 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 9 MARCH 2011 LAYING DOWN HARMONISED CONDITIONS FOR THE MARKETING OF CONSTRUCTION PRODUCTS AND REPEALING COUNCIL DIRECTIVE 89/106/EEC (TEXT WITH EEA RELEVANCE)
EN 13469:2012 Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation
EN 824:2013 Thermal insulating products for building applications - Determination of squareness
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
EN 823:2013 Thermal insulating products for building applications - Determination of thickness
ISO 8497:1994 Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes
EN ISO 13787:2003 Thermal insulation products for building equipment and industrial installations - Determination of declared thermal conductivity (ISO 13787:2003)
EN ISO 4589-1:2017 Plastics - Determination of burning behaviour by oxygen index - Part 1: General requirements (ISO 4589-1:2017)
VDI 2055 Blatt 1:2008-09 Thermal insulation of heated and refrigerated operational installations in the industry and the building services - Calculation rules
EN 13470:2001 Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation
EN 13238:2010 Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
EN 1602:2013 Thermal insulating products for building applications - Determination of the apparent density
ISO 11654:1997 Acoustics — Sound absorbers for use in buildings — Rating of sound absorption
EN 13472:2012 Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation
EN 1604:2013 Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions
EN ISO 354:2003 Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003)
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
EN 14707:2012 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation
ISO 10456:2007 Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
EN 14366:2004 Laboratory measurement of noise from waste water installations
EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
EN 1609:2013 Thermal insulating products for building applications - Determination of short term water absorption by partial immersion
EN ISO 11654:1997 Acoustics - Sound absorbers for use in buildings - Rating of sound absorption (ISO 11654:1997)
EN 15715:2009 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
EN ISO 11925-2:2010/AC:2011 REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
EN 12086:2013 Thermal insulating products for building applications - Determination of water vapour transmission properties
VDI 2055-3 : 2011 COR 2012 THERMAL INSULATION OF HEATED AND REFRIGERATED OPERATIONAL INSTALLATIONS IN THE INDUSTRY AND THE BUILDING SERVICES - TECHNICAL BASICS FOR THE VERIFICATION OF THERMOTECHNICAL PROPERTIES OF INSULATION SYSTEMS, DETERMINATION OF TOTAL HEAT LOSSES
ISO 4589-1:2017 Plastics — Determination of burning behaviour by oxygen index — Part 1: General requirements
EN 13172:2012 Thermal insulation products - Evaluation of conformity
EN 822:2013 Thermal insulating products for building applications - Determination of length and width

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.