EN 1434-2:2015
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Heat meters - Part 2: Constructional requirements
31-05-2016
04-11-2015
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Temperature sensors
5 Flow sensors
6 Calculators
7 Complete meter
8 Interfaces between sub-assemblies
9 Marking and security seals
Annex A (informative) - Examples of temperature sensors
Annex B (normative) - Input and output test signals
Annex C (informative) - Low voltage Power Supply for
heat meters and their sub-assemblies
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2004/22/EC, MID
Bibliography
This European Standard specifies the constructional requirements and applies to heat meters. Heat meters are instruments intended for measuring the energy which in a heat-exchange circuit is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units.Electrical safety requirements are not covered by this European Standard.Pressure safety requirements are not covered by this European Standard.Surface mounted temperature sensors are not covered by this European Standard.This standard covers meters for closed systems only, where the differential pressure over the thermal load is limited.
| Committee |
CEN/TC 176
|
| DevelopmentNote |
Supersedes PREN 1434-2. (11/2015)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| DS EN 1434-2 : 2015 | Identical |
| DIN EN 1434-2:2016-02 | Identical |
| NEN EN 1434-2 : 2015 | Identical |
| NS-EN 1434-2:2015 | Identical |
| NBN EN 1434-2 : 2015 | Identical |
| NF EN 1434-2+A1:2018 | Identical |
| ONORM EN 1434-2:2019 | Identical |
| UNE-EN 1434-2:2016 | Identical |
| ONORM EN 1434-2 : 2016 | Identical |
| UNI EN 1434-2 : 2007 | Identical |
| NF EN 1434-2 : 2016 | Identical |
| GOST R EN 1434-2 : 2011 | Identical |
| SN EN 1434-2 : 2016 | Identical |
| NS EN 1434-2 : 1997 | Identical |
| I.S. EN 1434-2:2015 | Identical |
| PN EN 1434-2 : 2016 | Identical |
| BS EN 1434-2 : 2015 | Identical |
| CSA C900.2:21 | Identical |
| 05/30127263 DC : DRAFT JAN 2005 | EN 1434-1 - HEAT METERS - PART 1: GENERAL REQUIREMENTS |
| BS EN 1434-1 : 2015 | HEAT METERS - PART 1: GENERAL REQUIREMENTS |
| 12/30259441 DC : 0 | BS EN 13757-1 - COMMUNICATION SYSTEM FOR AND REMOTE READING OF METERS - PART 1: DATA EXCHANGE |
| DIN EN 13757-1:2015-01 | Communication systems for meters - Part 1: Data exchange |
| I.S. EN 13757-1:2014 | COMMUNICATION SYSTEMS FOR METERS - PART 1: DATA EXCHANGE |
| I.S. EN 1434-1:2015 | HEAT METERS - PART 1: GENERAL REQUIREMENTS |
| DIN EN 1434-1:2016-02 | HEAT METERS - PART 1: GENERAL REQUIREMENTS |
| PREN 13757-1 : DRAFT 2012 | COMMUNICATION SYSTEM FOR AND REMOTE READING OF METERS - PART 1: DATA EXCHANGE |
| UNE-EN 1434-1:2016 | Heat meters - Part 1: General requirements |
| BS EN 13757-1:2014 | Communication systems for meters Data exchange |
| UNE-EN 13757-1:2015 | Communication systems for meters - Part 1: Data exchange |
| CSA C900.1 : 2013 | HEAT METERS - PART 1: GENERAL REQUIREMENTS |
| EN 1434-1:2015 | Heat meters - Part 1: General requirements |
| EN 13757-1:2014 | Communication systems for meters - Part 1: Data exchange |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| 2004/22/EC : 2004 | DIRECTIVE 2004/22/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 31 MARCH 2004 ON MEASURING INSTRUMENTS |
| EN 1092-3:2003/AC:2007 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES |
| ISO 4903:1989 | Information technology Data communication 15-pole DTE/DCE interface connector and contact number assignments |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 60947-5-6:2000 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| EN 60751:2008 | INDUSTRIAL PLATINUM RESISTANCE THERMOMETERS AND PLATINUM TEMPERATURE SENSORS |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| EN 1434-1:2015 | Heat meters - Part 1: General requirements |
| EN 1434-3:2015 | Heat meters - Part 3: Data exchange and interfaces |
| EN ISO 286-2:2010/AC:2013 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 2: TABLES OF STANDARD TOLERANCE CLASSES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS (ISO 286-2:2010/COR 1:2013) |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| IEC 60947-5-6:1999 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.