EN 16145:2012
Current
The latest, up-to-date edition.
19-12-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Designation
6 Marking
7 Materials
8 Dimensional Characteristics
9 Leaktightness Characteristics
10 Mechanical Characteristics
11 Hydraulic Characteristics
12 Backflow protection
13 Acoustic characteristics
14 Rotary connection
Annex A (informative) - Pressure take-off tee
Bibliography
This European Standard specifies:-the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply;-the procedures for testing these characteristics.It applies to extractable outlets made from any material which is intended for equipping and supplementing sanitary tapware for sinks and wash-basins used for culinary or ablutionary purposes. Such extractable outlets shall only be connected downstream of the obturator of the tapware.Extractable outlets with total closing device fitted after the obturator of the tapware are not covered by this standard. Such products will be tested in accordance with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).The conditions of use and classification are specified in Table 1.
Committee |
CEN/TC 164
|
DevelopmentNote |
Supersedes PREN 16145. (01/2013)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
NF EN 16145 : 2013 | Identical |
UNE-EN 16145:2014 | Identical |
NBN EN 16145 : 2013 | Identical |
SN EN 16145 : 2012 | Identical |
PN EN 16145 : 2013 | Identical |
NEN EN 16145 : 2013 | Identical |
BS EN 16145:2012 | Identical |
I.S. EN 16145:2012 | Identical |
NS EN 16145 : 2012 | Identical |
DIN EN 16145:2013-03 | Identical |
UNI EN 16145 : 2013 | Identical |
BS EN 16146 : 2012 | SANITARY TAPWARE - EXTRACTABLE SHOWER HOSES FOR SANITARY TAPWARE FOR SUPPLY SYSTEMS TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION |
DIN EN 1287:2015-07 (Draft) | SANITARY TAPWARE - LOW PRESSURE THERMOSTATIC MIXING VALVES - GENERAL TECHNICAL SPECIFICATION |
DIN EN 1111:2015-07 (Draft) | SANITARY TAPWARE - THERMOSTATIC MIXING VALVES (PN 10) - GENERAL TECHNICAL SPECIFICATION |
I.S. EN 1287:2017 | SANITARY TAPWARE - LOW PRESSURE THERMOSTATIC MIXING VALVES - GENERAL TECHNICAL SPECIFICATION |
EN 1111:2017 | Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification |
EN 1287:2017 | Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification |
DIN EN 1287:2017-10 | SANITARY TAPWARE - LOW PRESSURE THERMOSTATIC MIXING VALVES - GENERAL TECHNICAL SPECIFICATION |
DIN EN 1111:2017-10 | SANITARY TAPWARE - THERMOSTATIC MIXING VALVES (PN 10) - GENERAL TECHNICAL SPECIFICATION |
I.S. EN 1111:2017 | SANITARY TAPWARE - THERMOSTATIC MIXING VALVES (PN 10) - GENERAL TECHNICAL SPECIFICATION |
15/30321802 DC : 0 | BS EN 1111 - SANITARY TAPWARE - THERMOSTATIC MIXING VALVES (PN 10) - GENERAL TECHNICAL SPECIFICATION |
DIN EN 16146:2015-02 | Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification; German version EN 16146:2012+A1:2014 |
I.S. EN 16146:2012 | SANITARY TAPWARE - EXTRACTABLE SHOWER HOSES FOR SANITARY TAPWARE FOR SUPPLY SYSTEMS TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION |
BS EN 1111:2017 | Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification |
BS EN 1287:2017 | Sanitary tapware. Low pressure thermostatic mixing valves. General technical specification |
EN 16146:2012+A1:2014 | Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification |
PREN 1111 : DRAFT 2015 | SANITARY TAPWARE - THERMOSTATIC MIXING VALVES (PN 10) - GENERAL TECHNICAL SPECIFICATION |
UNI EN 16146 : 2014 | SANITARY TAPWARE - EXTRACTABLE SHOWER HOSES FOR SANITARY TAPWARE FOR SUPPLY SYSTEMS TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION |
UNE-EN 16146:2013 | Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification |
ISO 3822-1:1999 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement |
EN 817:2008 | Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications |
EN 1287:2017 | Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification |
EN 16146:2012+A1:2014 | Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification |
EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
ISO 3822-4:1997 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special appliances |
EN 1286:1999 | Sanitary tapware - Low pressure mechanical mixing valves - General technical specification |
EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
EN ISO 3822-4:1997 | Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances |
EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
EN 200:2008 | Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification |
EN ISO 3822-1:1999/A1:2008 | ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT |
EN 1111:2017 | Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.