EN 16307-1:2013+A1:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Industrial trucks - Safety requirements and verification - Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks
04-09-2020
29-07-2015
European foreword
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions .
4 Safety requirements and/or protective measures
5 Verification of safety requirements and/or protective
measures
6 Information for use
Annex A (informative) - List of significant hazards
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
This European Standard gives requirements for the types of industrial trucks specified in the scope of EN ISO 3691-1.This European Standard is intended to be used in conjunction with EN ISO 3691-1. These requirements are supplementary to those stated in EN ISO 3691-1 with the addition of hazards, which can occur when operating in potentially explosive atmospheres.This European standard covers the following requirements:-Electrical requirements-Noise emissions-Vibration-Electromagnetic compatibility (EMC)This European standard defines supplementary requirements to EN ISO 3691-1:-Travel speed-Brakes-Travel and breaking controls - Additional operation from alongside pedestrian-controlled and stand-on trucks-Lift chains-Mast tilt and carriage isolation-Operator's seat-Protection against crushing, shearing and trapping-Visibility-Information for use (instruction handbook and marking)Annex A (informative) contains the list of significant hazards covered by this European Standard.
| DevelopmentNote |
Supersedes PREN 16307-1. (01/2013) 2013 Edition Re-Issued in July 2015 & incorporates AMD 1 2015. (08/2015)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 16307-1 : 2015 | Identical |
| NF EN 16307-1 : 2013 + A1 2015 | Identical |
| NBN EN 16307-1 : 2013 + A1 2015 | Identical |
| NEN EN 16307-1 : 2013 + A1 2015 | Identical |
| NS EN 16307-1 : 2013 + A1 2015 | Identical |
| I.S. EN 16307-1:2013 | Identical |
| PN EN 16307-1 : 2013 + A1 2015 | Identical |
| SN EN 16307-1 : 2013 + A1 2015 | Identical |
| UNI EN 16307-1 : 2013 | Identical |
| UNI EN 16307-1 : 2015 | Identical |
| UNE-EN 16307-1:2013 | Identical |
| BS EN 16307-1 : 2013 | Identical |
| DIN EN 16307-1:2015-11 | Identical |
| DIN EN 16307-1 E : 2015 | Identical |
| UNE-EN 16307-1:2013+A1:2015 | Identical |
| DIN EN 16307-1:2019-01 (Draft) | Identical |
| BS EN 16307-1:2013+A1:2015 | Identical |
| BS EN 1755:2015 | Industrial Trucks. Safety requirements and verification. Supplementary requirements for operation in potentially explosive atmospheres |
| PREN 12312-15 : DRAFT 2017 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 15: BAGGAGE AND EQUIPMENT TRACTORS |
| DIN EN 1755:2016-02 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| I.S. EN 1755:2015 | INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - SUPPLEMENTARY REQUIREMENTS FOR OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| 13/30257895 DC : 0 | BS EN 1755 - SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST |
| UNE-EN 1755:2016 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| PREN 1755 : DRAFT 2013 | SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST |
| 17/30353474 DC : 0 | BS EN 12312-15 - AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 15: BAGGAGE AND EQUIPMENT TRACTORS |
| EN 1755:2015 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| ISO/TS 3691-8:2012 | Industrial trucks Safety requirements and verification Part 8: Regional requirements for countries outside the European Community |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| ISO 13564-1:2012 | Powered industrial trucks — Test methods for verification of visibility — Part 1: Sit-on and stand-on operator trucks and variable-reach trucks up to and including 10 t capacity |
| ISO 3691-1:2011 | Industrial trucks — Safety requirements and verification — Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks |
| EN ISO 11688-2 : 2000 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| EN 12895:2015 | Industrial trucks - Electromagnetic compatibility |
| EN 1755:2015 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 5053:1987 | Powered industrial trucks Terminology |
| EN 13059:2002+A1:2008 | Safety of industrial trucks - Test methods for measuring vibration |
| ISO 6292:2008 | Powered industrial trucks and tractors Brake performance and component strength |
| EN 13490:2001+A1:2008 | Mechanical vibration - Industrial trucks - Laboratory evaluation and specification of operator seat vibration |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 16203:2014 | Safety of Industrial Trucks - Dynamic tests for verification of lateral stability - Counterbalanced Trucks |
| EN ISO 3691-1:2015/AC:2016 | INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 1: SELF-PROPELLED INDUSTRIAL TRUCKS, OTHER THAN DRIVERLESS TRUCKS, VARIABLE-REACH TRUCKS AND BURDEN-CARRIER TRUCKS (ISO 3691-1:2011, INCLUDING COR 1:2013) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN 12053:2001+A1:2008 | Safety of industrial trucks - Test methods for measuring noise emissions |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.