EN 1802:2002
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Transportable gas cylinders - Periodic inspection and testing of seamless aluminium alloy gas cylinders
31-08-2002
20-02-2002
Foreword
Introduction
1 Scope
2 Normative references
3 Intervals between periodic inspection and test
4 List of procedures for periodic inspection and test
5 Identification of cylinder and preparation for
inspection and test
6 External visual inspection
7 Internal visual inspection
8 Supplementary tests
9 Inspection of cylinder neck/shoulder
10 Pressure test or ultrasonic test
11 Inspection of valve
12 Final operations
13 Rejection and rendering cylinder unserviceable
Annex A (informative) Gas cylinders manufactured
according to National Regulations
Annex B (normative) Inspection periods
Annex C (normative) Description, evaluation of defects
and conditions for rejection of seamless
aluminium alloy gas cylinders at time of
visual inspection
Annex D (normative) Procedure to be adopted when a
cylinder valve is suspected to be obstructed
Annex E (normative) Cleaning of aluminium alloy gas
cylinders
Annex F (normative) Proof pressure test of gas cylinders
Annex G (normative) Volumetric expansion testing of gas
cylinders
Annex H (normative) Ultrasonic test
Annex I (informative) Inspection and maintenance of
valves and their connections: recommended
procedures
Bibliography
This European Standard specifies the requirements for periodic inspection and testing of seamless aluminium alloy transportable gas cylinders (single or those from bundles) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l.NOTE As far as practicable, this standard may also be applied to cylinders of less than 0,5 l water capacity.This standard specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders to be reintroduced into service for a further period of time. It also defines a procedure to qualify existing gas cylinders for free movement between member states of the European Union (see annex A).This standard does not apply to periodic inspection and testing of acetylene cylinders or composite (fully wrapped or hoop-wrapped) aluminium alloy cylinders.
| Committee |
CEN/TC 23
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Withdrawn
|
| Standards | Relationship |
| SN EN 1802 : 2002 | Identical |
| UNI EN 1802 : 2004 | Identical |
| NEN EN 1802 : 2002 | Identical |
| BS EN 1802:2002 | Identical |
| PN EN 1802 : 2002 | Identical |
| NBN EN 1795 : 1998 | Identical |
| NBN EN 1802 : 2002 | Identical |
| NS EN 1802 : 1ED 2002 | Identical |
| UNE-EN 1802:2002 | Identical |
| NF EN 1802 : 2002 | Identical |
| I.S. EN 1802:2002 | Identical |
| DIN EN 1802:2002-09 | Identical |
| I.S. EN 14189:2003 | TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS |
| UNE-EN 15888:2014 | Transportable gas cylinders - Cylinder bundles - Periodic inspection and testing |
| DIN EN 15888:2014-07 | Transportable gas cylinders - Cylinder bundles - Periodic inspection and testing |
| EN 13365:2002/A1:2005 | TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES FOR PERMANENT AND LIQUEFIED GASES (EXCLUDING ACETYLENE) - INSPECTION AT TIME OF FILLING |
| BS EN 15888:2014 | Transportable gas cylinders. Cylinder bundles. Periodic inspection and testing |
| DIN EN 15888 E : 2014 | TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES - PERIODIC INSPECTION AND TESTING |
| 08/30195386 DC : 0 | BS EN 15888 - TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES - PERIODIC INSPECTION AND TESTING |
| I.S. EN 15888:2014 | TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES - PERIODIC INSPECTION AND TESTING |
| EN 15888:2014 | Transportable gas cylinders - Cylinder bundles - Periodic inspection and testing |
| BS EN 13385:2002 | Transportable gas cylinders. Battery vehicles for permanent and liquefied gases (excluding acetylene). Inspection at time of filling |
| EN 14189:2003 | Transportable gas cylinders - Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders |
| BS EN 14189:2003 | Transportable gas cylinders. Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders |
| UNI EN 15888 : 2014 | TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES - PERIODIC INSPECTION AND TESTING |
| DIN EN 13365:2005-11 | TRANSPORTABLE GAS CYLINDERS - CYLINDER BUNDLES FOR PERMANENT AND LIQUEFIED GASES (EXCLUDING ACETYLENE) - INSPECTION AT THE TIME OF FILLING |
| BS EN 13365:2002 | Transportable gas cylinders. Cylinder bundles for permanent and liquefied gases (excluding acetylene). Inspection at time of filling |
| DIN EN 14189:2003-09 | TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS |
| EN 13385:2002 | Transportable gas cylinders - Battery vehicles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling |
| EN 1975:1999/A1:2003 | TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS ALUMINIUM AND ALUMINIUM ALLOY GAS CYLINDERS OF CAPACITY FROM 0.5 LITRE UP TO 150 LITRE |
| EN 629-2 : 1996 | TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| PREN 14189 : DRAFT 2001 | TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS |
| EN 1089-1 : 1996 | TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - STAMPMARKING |
| PREN 1964-2 : DRAFT 1998 | TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS STEEL GAS CYLINDERS FROM 0.5 LITRE UP TO AND INCLUDING 150 LITRES - TENSILE STRENGTH |
| ISO 9303:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections |
| ISO 13341:2010 | Gas cylinders — Fitting of valves to gas cylinders |
| EN ISO 11114-1:2012/A1:2017 | GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1: 2012/AMD 1:2017) |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 1795 : 1997 | TRANSPORTABLE GAS CYLINDERS (EXCLUDING LPG) - PROCEDURES FOR CHANGE OF GAS SERVICE |
| ISO 10543:1993 | Seamless and hot-stretch-reduced welded steel tubes for pressure purposes Full peripheral ultrasonic thickness testing |
| ISO 11114-2:2013 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials |
| EN ISO 13341:2010/A1:2015 | Gas cylinders - Fitting of valves to gas cylinders - Amendment 1 (ISO 13341:2010/Amd 1:2015) |
| EN 583-1:1998/A1:2003 | NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - GENERAL PRINCIPLES |
| ISO 6506:1981 | Metallic materials — Hardness test — Brinell test |
| EN ISO 11114-2:2013 | Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013) |
| EN 1089-3:2011 | Transportable gas cylinders - Gas cylinder identification (excluding LPG) - Part 3: Colour coding |
| EN 849:1996/A2:2001 | TRANSPORTABLE GAS CYLINDERS - CYLINDER VALVES - SPECIFICATION AND TYPE TESTING |
| ISO 9764:1989 | Electric resistance and induction welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal imperfections |
| EN 837-1:1996/AC:1998 | PRESSURE GAUGES - BOURDON TUBE PRESSURE GAUGES - DIMENSIONS, METROLOGY, REQUIREMENTS AND TESTING |
| EN 1089-2 : 2002 | TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - PART 2: PRECAUTIONARY LABELS |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| ISO 9305:1989 | Seamless steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of transverse imperfections |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.