• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 196-1:2016

Current
Current

The latest, up-to-date edition.

Methods of testing cement - Part 1: Determination of strength
Published date

27-04-2016

European foreword
1 Scope
2 Normative references
3 Principle
4 Laboratory and equipment
5 Mortar constituents
6 Preparation of mortar
7 Preparation of test specimens
8 Conditioning of test specimens
9 Testing procedures
10 Results
11 Validation testing of CEN Standard sand
   and of alternative compaction equipment
Annex A (normative) - Alternative vibration compaction
        equipment and procedures validated as equivalent
        to the reference jolting compaction equipment and
        procedure

This part of EN 196 describes the method for the determination of the compressive and, optionally, the flexural strength of cement mortar. The method applies to common cements and to other cements and materials, the standards for which call up this method. It may not apply to other cement types that have, for example, a very short initial setting time.The method is used for assessing whether the compressive strength of cement is in conformity with its specification and for validation testing of a CEN Standard sand, EN 196 1, or alternative compaction equipment.This part of EN 196 describes the reference equipment and procedure and allows alternative compaction equipment and procedures to be used provided that they have been validated in accordance with the appropriate provisions in this document. In the event of a dispute, only the reference equipment and procedure are used.

DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

DIN EN 15191 E : 2010 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
06/30153624 DC : 0 EN 1308 - ADHESIVES FOR TILES - DETERMINATION OF SLIP
PD CR 14245:2001 Guidelines for the application of EN 197-2. Conformity Evaluation
CEN/TR 16912:2016 Guidelines for a procedure to support the European standardization of cements
I.S. EN 15368:2008 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS EN 16506:2014 Systems for renovation of drains and sewers. Lining with a rigidly anchored plastics inner layer (RAPL)
14/30314735 DC : 0 BS EN 12004-2 - ADHESIVES FOR TILES - PART 2: TEST METHODS
DIN EN 16506 E : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
07/30166977 DC : DRAFT AUG 2007 BS EN 1744-1 - TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
PD CR 13933:2000 Masonry cement. Testing for workability (cohesivity)
I.S. EN 12002:2008 ADHESIVES FOR TILES - DETERMINATION OF TRANSVERSE DEFORMATION FOR CEMENTITIOUS ADHESIVES AND GROUTS
PREN 13279-2 : DRAFT 2013 GYPSUM BINDERS AND GYPSUM PLASTERS - PART 2: TEST METHODS
PREN 598 : DRAFT 2017 COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS
S.R. CEN/TR 15840:2009 EVALUATION OF CONFORMITY OF FLY ASH FOR CONCRETE - GUIDELINES FOR THE APPLICATION OF EN 450-2
02/104526 DC : DRAFT JULY 2002 EN 13263-2 - SILICA FUME FOR CONCRETE - PART 2: CONFORMITY EVALUATION
09/30205526 DC : 0 BS EN 197-1 - CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR COMMON CEMENTS
DIN EN 16506:2014-12 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
PREN 13454-2 : DRAFT 2017 BINDERS AND FACTORY MADE MIXTURES FOR FLOOR SCREEDS BASED ON CALCIUM SULPHATE - PART 2: TEST METHODS
95/102636 DC : DRAFT APRIL 1995 PREN 1771 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF INJECTABILITY AND SPLITTING TEST
DIN EN 13282-2:2015-07 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
03/319412 DC : DRAFT NOV 2003 EN 12878 - PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
BS EN 12004-2:2017 Adhesives for ceramic tiles Test methods
DD ENV 197-2:1996 Cement Conformity evaluation
ISO 12439:2010 Mixing water for concrete
I.S. EN ISO 10426-1:2009 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION (ISO 10426-1:2009)
BS EN 14490:2010 Execution of special geotechnical works. Soil nailing
05/30131382 DC : DRAFT MAR 2005 BS EN 15184 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - SHEAR ADHESION COATED STEEL TO CONCRETE (PULL-OUT TEST)
02/123276 DC : DRAFT AUG 2002 BS EN 1062-7 - PAINTS AND VARNISHES - COATING MATERIALS AND COATING SYSTEMS FOR EXTERIOR MASONRY AND CONCRETE - PART 7: DETERMINATION OF CRACK BRIDGING PROPERTIES
06/30153639 DC : 0 EN 1348 - ADHESIVES FOR TILES - DETERMINATION OF TENSILE ADHESION STRENGTH FOR CEMENTITIOUS ADHESIVES
06/30153633 DC : 0 EN 1346 - ADHESIVES FOR TILES - DETERMINATION OF OPEN TIME
UNE-EN 15191:2011 Precast concrete products - Classification of glassfibre reinforced concrete performance
PREN 13282-1 : DRAFT 2010 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS ISO 13640:1999 Building construction. Jointing products. Specifications for test substrates
I.S. EN 15743:2010 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS EN 15368 : 2008 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN 13282-3:2015 HYDRAULIC ROAD BINDERS - PART 3: CONFORMITY EVALUATION
PREN 1015-11 : DRAFT 2017 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 11: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH OF HARDENED MORTAR
I.S. EN 14944-3:2007 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 3: MIGRATION OF SUBSTANCES FROM FACTORY-MADE CEMENTITITOUS PRODUCTS
S.R. CEN/TR 16563:2013 PRINCIPLES OF THE EQUIVALENT DURABILITY PROCEDURE
15/30317321 DC : 0 BS EN 14944-1 - INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF MIGRATION FROM FACTORY MADE CEMENTITIOUS PRODUCTS ON THE ORGANOLEPTIC PARAMETERS
EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
DIN EN 14227-4:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
DIN EN 12715:2000-10 Execution of special geotechnical work - Grouting; English version of DIN EN 12715
DIN EN 196-3:2016-05 (Draft) METHODS OF TESTING CEMENT - PART 3: DETERMINATION OF SETTING TIMES AND SOUNDNESS
DIN EN 14216 E : 2015 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
BS EN 13687-3:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility Thermal cycling without de-icing salt impact
BS EN 450-1:2012 Fly ash for concrete Definition, specifications and conformity criteria
BS EN 450-2:2005 Fly ash for concrete Conformity evaluation
BS EN 480-14:2006 Admixtures for concrete, mortar and grout. Test methods Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
BS EN 15183:2006 Products and systems for the protection and repair of concrete structures. Test methods. Corrosion protection test
UNE-EN 14496:2017 Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods
BS EN 445:2007 Grout for prestressing tendons. Test methods
EN 197-2:2014 Cement - Part 2: Conformity evaluation
BS EN 13687-2:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility Thunder-shower cycling (thermal shock)
BS EN 13412:2006 Products and systems for the protection and repair of concrete structures. Test methods. Determination of modulus of elasticity in compression
UNE-EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
BS EN 13279-2:2014 Gypsum binders and gypsum plasters Test methods
BS EN 12636:1999 Products and systems for the protection and repair of concrete structures. Test methods. Determination of adhesion concrete to concrete
BS EN 14498:2004 Products and systems for the protection and repair of concrete structures. Test methods. Volume and weight changes of injection products after air drying and water storage cycles
BS EN 196-3 : 2005 METHODS OF TESTING CEMENT - PART 3: DETERMINATION OF SETTING TIMES AND SOUNDNESS
BS EN 12715:2000 Execution of special geotechnical work. Grouting
BS EN 14227-4:2013 Hydraulically bound mixtures. Specifications Fly ash for hydraulically bound mixtures
BS EN 480-2:2006 Admixtures for concrete, mortar and grout. Test methods Determination of setting time
BS EN 13892-1:2002 Methods of test for screed materials Sampling, making and curing specimens for test
BS EN 1308:1999 Adhesives for tiles. Determination of slip
BS EN 12615:1999 Products and systems for the protection and repair of concrete structures. Test methods. Determination of slant shear strength
BS EN 13294:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of stiffening time
I.S. EN 413-2:2016 MASONRY CEMENT - PART 2: TEST METHODS
I.S. EN 13263-2:2005 SILICA FUME FOR CONCRETE - PART 2: CONFORMITY EVALUATION
I.S. EN 459-2:2010 BUILDING LIME - PART 2: TEST METHODS
I.S. EN 13279-2:2014 GYPSUM BINDERS AND GYPSUM PLASTERS - PART 2: TEST METHODS
I.S. EN 12808-2:2008 GROUTS FOR TILES - PART 2: DETERMINATION OF RESISTANCE TO ABRASION
EN 13395-1:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 1: Test for flow of thixotropic mortars
EN 13263-2:2005+A1:2009 Silica fume for concrete - Part 2: Conformity evaluation
DIN EN 12808-3:2009-01 Grouts for tiles - Determination of flexural and compressive strength
EN 13294:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time
EN 13412:2006 Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
EN 12002:2008 Adhesives for tiles - Determination of transverse deformation for cementitious adhesives and grouts
DIN EN 14891:2017-05 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
EN 13279-2:2014 Gypsum binders and gypsum plasters - Part 2: Test methods
DIN EN 14496:2017-09 GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
EN 12808-4:2009/AC:2011 GROUTS FOR TILES - PART 4: DETERMINATION OF SHRINKAGE
EN 13295:2004 Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation
DIN EN 445:2008-01 Grout for prestressing tendons - Test methods
EN 13057:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance of capillary absorption
EN 12618-1:2003 Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Adhesion and elongation capacity of injection products with limited ductility
EN 12808-2:2008 Grouts for tiles - Part 2: Determination of resistance to abrasion
EN 12617-4:2002 Products and systems for the protection and repair of concrete structures - Test methods - Part 4: Determination of shrinkage and expansion
EN 12636:1999 Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete
EN 13263-1:2005+A1:2009 Silica fume for concrete - Part 1: Definitions, requirements and conformity criteria
EN 1051-1:2003 Glass in building - Glass blocks and glass pavers - Part 1: Definitions and description
CEN/TR 16563:2013 Principles of the equivalent durability procedure
EN 1062-7:2004 Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 7: Determination of crack bridging properties
ENV 197-2 : 1995 CEMENT - CONFORMITY EVALUATION
EN 13395-3:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 3: Test for flow of repair concrete
EN 13213 : 2001 HOLLOW FLOORS
EN 1348:2007 Adhesives for tiles - Determination of tensile adhesion strength for cementitious adhesives
EN 13396:2004 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of chloride ion ingress
I.S. EN 14944-1:2006 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF FACTORY MADE CEMENTITIOUS PRODUCTS ON ORGANOLEPTIC PARAMETERS
ENV 13282:2000 Hydraulic road binders - Composition, specifications and conformity criteria
ONORM EN 13454-2 : 2007 BINDERS, COMPOSITE BINDERS AND FACTORY MADE MIXTURES FOR FLOOR SCREEDS BASED ON CALCIUM SULFATE - PART 2: TEST METHODS
10/30200034 DC : 0 BS EN 13282-1 - HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 15191:2010-04 Precast concrete products - Classification of glassfibre reinforced concrete performance
I.S. EN ISO 16000-11:2006 INDOOR AIR - PART 11: DETERMINATION OF THE EMISSION OF VOLATILE ORGANIC COMPOUNDS FROM BUILDING PRODUCTS AND FURNISHING - SAMPLING, STORAGE OF SAMPLES AND PREPARATION OF TEST SPECIMENS
08/30183119 DC : DRAFT AUG 2008 BS EN 459-2 - BUILDING LIME - PART 2: TEST METHODS
05/30131069 DC : DRAFT MAR 2005 EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
BS EN 15743 : 2010 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
NF EN 15368 : 2009 + A1 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
13/30278741 DC : 0 BS EN 13279-2 - GYPSUM BINDERS AND GYPSUM PLASTERS - PART 2: TEST METHODS
08/30174775 DC : DRAFT FEB 2008 BS EN 12808-2 - GROUTS FOR TILES - PART 2: DETERMINATION OF RESISTANCE TO ABRASION
08/30183116 DC : DRAFT AUG 2008 BS EN 459-1 - BUILDING LIME - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 15368 E : 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
11/30240492 DC : 0 BS EN 14227-4 - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
12/30254896 DC : 0 BS EN 197-2 - CEMENT - PART 2: CONFORMITY EVALUATION
11/30248435 DC : 0 BS EN 14891 - LIQUID-APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
DD ENV 459-1:1995 Building lime Definitions, specifications and conformity criteria
14/30314741 DC : 0 BS EN 14891 - LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
02/104525 DC : DRAFT JULY 2002 EN 13263-1 - SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
S.R. CEN/TR 14245:2014 CEMENT - GUIDELINES FOR THE APPLICATION OF EN 197-2 CONFORMITY EVALUATION
UNE-EN 15368:2010 Hydraulic binder for non-structural applications: definition, specifications and conformity criteria
13/30282202 DC : 0 BS EN 16622 - HYDRAULIC SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
DIN EN 13282-1:2013-06 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
PREN 197-1 : DRAFT 2014 CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR COMMON CEMENTS
DIN 4226-2:2002-02 AGGREGATES FOR CONCRETE AND MORTAR - PART 2: LIGHTWEIGHT AGGREGATES
DIN EN 16622:2016-02 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
I.S. EN 13454-2:2004 BINDERS, COMPOSITE BINDERS AND FACTORY MADE MIXTURES FOR FLOOR SCREEDS BASED ON CALCIUM SULFATE - PART 2: TEST METHODS
17/30351887 DC : 0 BS EN 1015-11 - METHODS OF TEST FOR MORTAR FOR MASONRY - PART 11: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH OF HARDENED MORTAR
S.R. CEN/TR 16912:2016 GUIDELINES FOR A PROCEDURE TO SUPPORT THE EUROPEAN STANDARDIZATION OF CEMENTS
I.S. EN 10298:2005 STEEL TUBES AND FITTINGS FOR ON SHORE AND OFFSHORE PIPELINES - INTERNAL LINING WITH CEMENT MORTAR
UNE-EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, assessment and verification of constancy of performance, classification and marking
EN ISO 10426-1:2009/AC:2018 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION - TECHNICAL CORRIGENDUM 2 (ISO 10426-1:2009/COR 2:2012)
S.R. CR 13933:2000 MASONRY CEMENT - TESTING FOR WORKABILITY (COHESIVITY)
DIN EN 197-2:2014-05 CEMENT - PART 2: CONFORMITY EVALUATION
DIN EN 13263-2:2009-07 SILICA FUME FOR CONCRETE - PART 2: CONFORMITY EVALUATION
DIN EN 13279-2:2014-03 Gypsum binders and gypsum plasters - Part 2: Test methods; German version EN 13279-2:2014
DIN EN 1347:2007-10 ADHESIVES FOR TILES - DETERMINATION OF WETTING CAPABILITY
DIN EN 480-13:2015-08 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 13: REFERENCE MASONRY MORTAR FOR TESTING MORTAR ADMIXTURES
DIN EN 13412:2006-11 Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
DIN EN 15184 E : 2006 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - SHEAR ADHESION OF COATED STEEL TO CONCRETE (PULL-OUT TEST)
DIN EN 14216:2015-09 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
DIN EN 14891 E : 2017 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
DIN EN 14679:2005-07 Execution of special geotechnical works - Deep mixing
DIN EN 598:2009-10 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009)
DIN EN 15183 E : 2006 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - CORROSION PROTECTION TEST
DIN EN 12002:2009-01 ADHESIVES FOR TILES - DETERMINATION OF TRANSVERSE DEFORMATION FOR CEMENTITIOUS ADHESIVES AND GROUTS
DIN EN 14496:2016-02 (Draft) GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
BS EN 598 : 2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
UNE-EN 13279-2:2014 Gypsum binders and gypsum plasters - Part 2: Test methods
BS EN 1347:1999 Adhesives for tiles. Determination of wetting capability
DIN EN 14891:2015-02 (Draft) LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
UNE-EN 196-9:2011 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
UNE-EN 545:2011 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
ISO 16000-11:2006 Indoor air — Part 11: Determination of the emission of volatile organic compounds from building products and furnishing — Sampling, storage of samples and preparation of test specimens
BS EN 12808-3:2008 Grouts for tiles Determination of flexural and compressive strength
BS EN 480-5:2005 Admixtures for concrete, mortar and grout. Test methods Determination of capillary absorption
BS EN 12618-3:2004 Products and systems for the protection and repair of concrete structures. Test methods Determination of the adhesion of injection products, with or without thermal cycling. Slant shear method
I.S. EN 480-5:2005 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 5: DETERMINATION OF CAPILLARY ABSORPTION
I.S. EN 598:2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
I.S. EN 14216:2015 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
DIN EN 13687-5:2002-05 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF THE THERMAL COMPATIBILITY - PART 5: RESISTANCE TO TEMPERATURE SHOCK
I.S. EN 450-1:2012 FLY ASH FOR CONCRETE - PART 1: DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN 480-2:2007 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 2: DETERMINATION OF SETTING TIME
I.S. EN 196-9:2010 METHODS OF TESTING CEMENT - PART 9: HEAT OF HYDRATION - SEMI-ADIABATIC METHOD
DIN EN 13687-2:2002-05 Products and systems for the protection and repair of concrete structures - Test methods; Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock); German version EN 13687-2:2002
I.S. EN 14496:2017 GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
DIN EN 1308:2007-11 ADHESIVES FOR TILES - DETERMINATION OF SLIP
DIN EN 13687-1:2002-05 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF THERMAL COMPATIBILITY - PART 1: FREEZE-THAW CYCLING WITH DE-ICING SALT IMMERSION
I.S. EN 480-13:2015 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 13: REFERENCE MASONRY MORTAR FOR TESTING MORTAR ADMIXTURES
DIN EN 13294:2002-09 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF STIFFENING TIME
I.S. EN 13412:2006 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF MODULUS OF ELASTICITY IN COMPRESSION
DIN EN 1347:1999-03 ADHESIVES FOR TILES - DETERMINATION OF WETTING CAPABILITY
I.S. EN 1347:2007 ADHESIVES FOR TILES - DETERMINATION OF WETTING CAPABILITY
I.S. EN 197-1:2011 CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR COMMON CEMENTS
I.S. EN 12808-3:2008 GROUTS FOR TILES - PART 3: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
DIN EN 1348:2007-11 ADHESIVES FOR TILES - DETERMINATION OF TENSILE ADHESION STRENGTH FOR CEMENTITIOUS ADHESIVES
I.S. EN 196-10:2016 METHODS OF TESTING CEMENT - PART 10: DETERMINATION OF THE WATER-SOLUBLE CHROMIUM (6) CONTENT OF CEMENT
I.S. EN 196-3:2016 METHODS OF TESTING CEMENT - PART 3: DETERMINATION OF SETTING TIMES AND SOUNDNESS
I.S. EN 12808-5:2008 GROUTS FOR TILES - PART 5: DETERMINATION OF WATER ABSORPTION
DIN EN 1346:2007-11 ADHESIVES FOR TILES - DETERMINATION OF OPEN TIME
I.S. EN 480-1:2014 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
EN 12715 : 2000 EXECUTION OF SPECIAL GEOTECHNICAL WORK - GROUTING
DIN EN 13584:2003-11 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF CREEP IN COMPRESSION FOR REPAIR PRODUCTS
DIN EN 12878:1999-09 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 413-1:2011-07 Masonry cement - Part 1: Composition, specifications and conformity criteria
DIN EN 197-1:2011-11 Cement - Part 1: Composition, specifications and conformity criteria for common cements
DIN EN 197-2:2000-11 CEMENT - PART 2: CONFORMITY EVALUATION
I.S. EN 12808-4:2009 GROUTS FOR TILES - PART 4: DETERMINATION OF SHRINKAGE
I.S. EN 14227-4:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
I.S. EN 13263-1:2005 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
DIN EN 14016-2:2004-04 Binders for magnesite screeds - Caustic magnesia and magnesium chloride - Part 2: Test methods; German version EN 14016-2:2004
I.S. EN 545:2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
I.S. EN 12878:2014 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 13395-3:2002-09 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF WORKABILITY - PART 3: TEST FOR FLOW OF REPAIR CONCRETE
DIN EN 13687-3:2002-05 Products and systems for the protection and repair of concrete structures - Test methods; Determination of thermal compatibility - Part 3: Thermal cycling without de-icing salt impact; German version EN 13687-3:2002
DIN EN 13687-4:2002-05 Products and systems for the protection and repair of concrete structures - Test method; Determination of thermal compatibility - Part 4: Dry thermal cycling; German Version EN 13687-4:2002
DIN EN 1015-2:2007-05 Methods of test for mortar for masonry - Part 2: Bulk sampling of mortars and preparation of test mortars (includes Amendment A1:2006)
I.S. EN 413-1:2011 MASONRY CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 197-4:2004-08 CEMENT - PART 4: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW EARLY STRENGTH BLAST FURNACE CEMENTS
I.S. EN 14891:2017 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
DIN EN 14016-1:2004-04 Binders for magnesite screeds - Caustic magnesia and magnesium chloride - Part 1: Definitions, requirements; German version EN 14016-1:2004
I.S. EN 445:2007 GROUT FOR PRESTRESSING TENDONS - TEST METHODS
I.S. EN 13851:2003 METHODS OF TEST FOR HYDRAULIC SETTING FLOOR SMOOTHING AND/OR LEVELLING COMPOUNDS - DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
I.S. EN 1744-1:2009 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
UNI EN 445 : 2007 GROUT FOR PRESTRESSING TENDONS - TEST METHODS
UNI EN 12878 : 2014 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
BS 3892-1:1993 Pulverized-fuel ash Specification for pulverized-fuel ash for use with Portland cement
BS 146:1991 Specification for Portland blastfurnace cement
ONORM EN 12808-3 : 2009 GROUTS FOR TILES - PART 3: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
I.S. EN 13395-1:2002 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF WORKABILITY - PART 1: TEST FOR FLOW OF THIXOTROPIC MORTARS
ONORM EN 12808-5 : 2009 GROUTS FOR TILES - PART 5: DETERMINATION OF WATER ABSORPTION
BS 6699:1992 Specification for ground granulated blastfurnace slag for use with Portland cement
BS 4246:1991 Specification for high slag blastfurnace cement
BS 12:1991 Specification for Portland cement
DIN EN 13282-3:2015-06 HYDRAULIC ROAD BINDERS - PART 3: CONFORMITY EVALUATION
I.S. EN 1346:2007 ADHESIVES FOR TILES - DETERMINATION OF OPEN TIME
I.S. EN 450-2:2005 FLY ASH FOR CONCRETE - PART 2: CONFORMITY EVALUATION
DD ENV 197-1:1995 Cement Composition, specifications and conformity criteria. Common cements
16/30332911 DC : 0 BS EN 14496 - GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
98/101455 DC : DRAFT FEB 1998 PREN ISO 12957-1:1998 - GEOTEXTILES AND GEOTEXTILE-RELATED PRODUCTS - DETERMINATION OF THE FRICTION CHARACTERISTICS - PART 1: DIRECT SHEAR TEST
08/30181473 DC : DRAFT JULY 2008 BS EN 545 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
PD CEN/TR 14245:2014 Cement. Guidelines for the application of EN 197-2 Conformity Evaluation
DIN EN 13282-2 E : 2015 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNE-EN 15743:2010 Supersulfated cement - Composition, specifications and conformity criteria
93/102674 DC : 0 PREN 1015-13 - METHODS OF TEST FOR MORTAR FOR MASONRY - PART 13: DETERMINATION OF DIMENSIONAL STABILITY OF HARDENED MORTARS
PREN 16506 : DRAFT 2012 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
DIN EN 15743:2015-06 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 16506 : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
14/30278089 DC : 0 BS ISO 13007-5 - CERAMIC TILES - GROUTS AND ADHESIVES - PART 5: LIQUID APPLIED WATERPROOFING MEMBRANES FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
PREN 12808-4 : DRAFT 2008 GROUTS FOR TILES - PART 4: DETERMINATION OF SHRINKAGE
08/30174778 DC : DRAFT FEB 2008 BS EN 12808-3 - GROUTS FOR TILES - PART 3: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
06/30119204 DC : 0 EN 14891 - LIQUID-APPLIED WATERPROOFING MEMBRANES FOR USE BENEATH CERAMIC TILING - DEFINITIONS, SPECIFICATIONS AND TEST METHODS
05/30123177 DC : DRAFT FEB 2005 BS EN 196-10 - METHODS OF TESTING CEMENT - PART 10: DETERMINATION OF THE WATER SOLUBLE CHROMIUM (6) CONTENT OF CEMENT
05/30131376 DC : DRAFT MAR 2005 BS EN 15183 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - CORROSION PROTECTION TEST
05/30129418 DC : DRAFT FEB 2005 BS EN 480-2 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 2: DETERMINATION OF SETTING TIME
PREN 14891 : DRAFT 2014 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
07/30172380 DC : 0 BS EN 14490 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
API 10A REDLINE : 2010 SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING
02/100390 DC : DRAFT JAN 2002 PREN 450-2 - FLY ASH FOR CONCRETE - PART 2: CONFORMITY EVALUATION
ISO 10426-1:2009 Petroleum and natural gas industries Cements and materials for well cementing Part 1: Specification
17/30357424 DC : 0 BS EN 13454-2 - BINDERS AND FACTORY MADE MIXTURES FOR FLOOR SCREEDS BASED ON CALCIUM SULPHATE - PART 2: TEST METHODS
DIN EN 14944-3:2015-06 (Draft) INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 3: MIGRATION OF SUBSTANCES FROM FACTORY-MADE CEMENTITIOUS PRODUCTS
NF EN 15191 : 2010 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCES
CR 13933:2000 Masonry cement - Testing for workability (cohesivity)
I.S. EN 16622:2015 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
PREN 197-2 : DRAFT 2012 CEMENT - PART 2: CONFORMITY EVALUATION
DIN EN 12004-2:2015-02 (Draft) ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
UNE-EN 13282-3:2015 Hydraulic road binders - Part 3: Conformity evaluation
PREN 15191 : DRAFT 2009 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASS-FIBRE REINFORCED CONCRETE PERFORMANCES
ISO 21690:2006 Glass in building Glass blocks Specification and test methods
S.R. CR 14245:2001 GUIDELINES FOR THE APPLICATION OF EN 197-2 'CONFORMITY EVALUATION'
DIN EN 13263-1:2009-07 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
DIN EN 12878:2014-07 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 1744-1:2013-03 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
DIN EN 934-5:2008-02 Admixtures for concrete, mortar and grout - Part 5: Admixtures for sprayed concrete - Definitions, requirements, conformity, marking and labelling
DIN EN 196-9:2010-07 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
DIN EN 480-14:2007-03 Admixtures for concrete, mortar and grout - Test methods - Part 14: Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
DIN EN 1771:2004-11 Products and systems for the protection and repair of concrete structures - Test methods - Determination of injectability using the sand column test
DIN EN 480-1:2015-01 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
DIN EN 14647:2006-01 Calcium aluminate cement - Composition, specifications and conformity criteria
BS EN 413-2:2016 Masonry cement Test methods
BS EN 459-2:2010 Building lime Test methods
BS EN 12190:1999 Products and systems for the protection and repair of concrete structures. Test methods. Determination of compressive strength of repair mortar
BS EN 14647:2005 Calcium aluminate cement. Composition, specifications and conformity criteria
BS EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines. Requirements and test methods
BS EN 13263-2 : 2005 SILICA FUME FOR CONCRETE - PART 2: CONFORMITY EVALUATION
BS EN 12808-4:2009 Grouts for tiles Determination of shrinkage
UNE-EN 459-2:2011 Building lime - Part 2: Test methods
UNE-EN 480-13:2015 Admixtures for concrete, mortar and grout - Test methods - Part 13: Reference masonry mortar for testing mortar admixtures
BS EN 14016-1:2004 Binders for magnesite screeds. Caustic magnesia and magnesium chloride Definitions, requirements
BS EN 1348:1999 Adhesives for tiles. Determination of tensile adhesion strength for cementitious adhesives
BS EN 13395-3:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability Test for flow of repair concrete
BS EN 197-2:2014 Cement Conformity evaluation
BS EN 1051-1:2003 Glass in building. Glass blocks and glass pavers Definitions and description
BS EN 13395-4:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability Application of repair mortar overhead
BS EN 13213:2001 Hollow floors
BS EN 13396:2004 Products and systems for the protection and repair of concrete structures. Test methods. Measurement of chloride ion ingress
BS EN 197-1:2011 Cement Composition, specifications and conformity criteria for common cements
UNE-EN 480-1:2015 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
DIN EN 14944-3:2009-01 Influence of cementitious products on water intended for human consumption - Test methods - Part 3: Migration of substances from factory-made cementitious products
BS EN 1542:1999 Products and systems for the protection and repair of concrete structures. Test methods. Measurement of bond strength by pull-off
EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
EN 13454-2:2003+A1:2007 Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate - Part 2: Test methods
EN 16506:2014 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
EN 480-5:2005 Admixtures for concrete, mortar and grout - Test methods - Part 5: Determination of capillary absorption
EN 196-9:2010 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
EN ISO 16000-11:2006 Indoor air - Part 11: Determination of the emission of volatile organic compounds from building products and furnishing - Sampling, storage of samples and preparation of test specimens (ISO 16000-11:2006)
EN 13584:2003 Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products
UNI EN 1744-1 : 2013 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
UNI EN 413-1 : 2011 MASONRY CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 15167-2 : 2006 GROUND GRANULATED BLAST FURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 2: CONFORMITY EVALUATION
UNI EN 14647 : 2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 13263-1 : 2009 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
EN 413-2:2016 Masonry cement - Part 2: Test methods
UNI EN 1348 : 2008 ADHESIVES FOR TILES - DETERMINATION OF TENSILE ADHESION STRENGTH FOR CEMENTITIOUS ADHESIVES
UNI EN 197-1 : 2011 CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR COMMON CEMENTS
UNI EN 480-1 : 2014 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
UNI EN 934-5 : 2008 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 5: ADMIXTURES FOR SPRAYED CONCRETE - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
UNI EN 1347 : 2007 ADHESIVES FOR TILES - DETERMINATION OF WETTING CAPABILITY
UNI EN 14227-4 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTUREE
UNI EN 14679 : 2005 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
UNI EN 13279-2 : 2014 GYPSUM BINDERS AND GYPSUM PLASTERS - PART 2: TEST METHODS
EN 12808-5:2008 Grouts for tiles - Part 5: Determination of water absorption
UNI EN 12808-5 : 2009 GROUTS FOR TILES - PART 5: DETERMINATION OF WATER ABSORPTION
UNI EN 13263-2 : 2009 SILICA FUME FOR CONCRETE - PART 2: CONFORMITY EVALUATION
UNI EN 15167-1 : 2006 GROUND GRANULATED BLAST FURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 12808-3 : 2009 GROUTS FOR TILES - PART 3: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
UNI EN 12002 : 2009 ADHESIVES FOR TILES - DETERMINATION OF TRANSVERSE DEFORMATION FOR CEMENTITIOUS ADHESIVES AND GROUTS
UNI EN 12808-2 : 2009 GROUTS FOR TILES - PART 2: DETERMINATION OF RESISTANCE TO ABRASION
UNI EN 545 : 2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
UNI EN 12808-4 : 2009 GROUTS FOR TILES - PART 4: DETERMINATION OF SHRINKAGE
EN 13687-5:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 5: Resistance to temperature shock
UNI EN 450-1 : 2012 FLY ASH FOR CONCRETE - PART 1: DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 1771 : 2005 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF INJECTABILITY AND SPLITTING TEST
UNI CEN/TR 16563 : 2013 PRINCIPLES OF THE EQUIVALENT DURABILITY PROCEDURE
UNI EN 598 : 2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
UNI EN ISO 10426-1 : 2010 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION
UNI EN 196-9 : 2010 METHODS OF TESTING CEMENT - PART 9: HEAT OF HYDRATION - SEMI-ADIABATIC METHOD
UNI EN 480-14 : 2007 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 14: DETERMINATION OF THE EFFECT ON CORROSION SUSCEPTIBILITY OF REINFORCING STEEL BY POTENTIOSTATIC ELECTRO-CHEMICAL TEST
12/30275810 DC : 0 BS EN 16506 - SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
PREN 12878 : DRAFT 2012 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
01/104967 DC : DRAFT JUN 2001 PREN 197-3 - CEMENT - PART 3: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW HEAT COMMON CEMENTS
03/310129 DC : DRAFT JULY 2003 EN 934-5 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 5: ADMIXTURES FOR SPRAYED CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY
I.S. EN 1348:2007 ADHESIVES FOR TILES - DETERMINATION OF TENSILE ADHESION STRENGTH FOR CEMENTITIOUS ADHESIVES
UNI CEN/TR 14245 : 2015 CEMENT - GUIDELINES FOR THE APPLICATION OF EN 197-2 CONFORMITY EVALUATION
DIN EN 14490:2010-11 Execution of special geotechnical works - Soil nailing
ISO 13640:1999 Building construction Jointing products Specifications for test substrates
UNE-EN 16622:2016 Silica-calcium fume for concrete - Definitions, requirements and conformity criteria
I.S. EN 1308:2007 ADHESIVES FOR TILES - DETERMINATION OF SLIP
BS ISO 13007-5:2015 Ceramic tiles. Grouts and adhesives Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
DIN EN 15368:2010-11 Hydraulic binder for non-structural applications - Definition, specifications and conformity criteria (includes Amendment A1:2010)
03/303958 DC : DRAFT APR 2003 EN 14679 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
PREN 14227-4 : DRAFT 2011 SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
03/312990 DC : DRAFT SEP 2003 BS EN 413-2 - MASONRY CEMENT - PART 2: TEST METHODS
99/109099 DC : DRAFT NOV 1999 BS EN 13738 - GEOTEXTILES AND GEOTEXTILE-RELATED PRODUCTS - DETERMINATION OF PULLOUT RESISTANCE IN SOIL
07/30164098 DC : 0 BS ISO 29582-2 - METHODS OF TESTING CEMENT - DETERMINATION OF THE HEAT OF HYDRATION - PART 2: SEMI-ADIABATIC METHOD
PD CEN/TR 15840:2009 Evaluation of conformity of fly ash for concrete. Guidelines for the application of EN 450-2
14/30300225 DC : DRAFT JUNE 2014 BS EN 197-1 - CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR COMMON CEMENTS
96/108350 DC : DRAFT NOV 1996 PREN 12618-3 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF THE ADHESION OF INJECTION PRODUCTS, WITH OR WITHOUT THERMAL CYCLING - PART 3: SLANT SHEAR METHOD
PD CEN/TR 16563:2013 Principles of the equivalent durability procedure
DIN EN 15743 E : 2015 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 16622 E : 2016 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
PREN 14496 : DRAFT 2016 GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
03/303925 DC : DRAFT MAR 2003 BS EN 14647 - CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
98/101458 DC : DRAFT FEB 1998 PREN ISO 12957-2:1998 - GEOTEXTILES AND GEOTEXTILE-RELATED PRODUCTS - DETERMINATION OF THE FRICTION CHARACTERISTICS - PART 2: INCLINED PLANE TEST
PD 6534:1993 Guide to the use in the UK of DD ENV 206:1992. Concrete. Performance, production, placing and compliance criteria
BS EN 16622:2015 Silica-calcium fume for concrete. Definitions, requirements and conformity criteria
03/112934 DC : 0 ISO 21690 - GLASS IN BUILDING - GLASS BLOCKS - SPECIFICATION
BS 7583:1992 Specification for Portland limestone cement
08/30174781 DC : DRAFT FEB 2008 BS EN 12808-5 - GROUTS FOR TILES - PART 5: DETERMINATION OF WATER ABSORPTION
04/30083253 DC : DRAFT MAY 2004 EN 14944-1 - INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF FACTORY MADE CEMENTITIOUS PRODUCTS ON ORGANOLEPTIC PARAMETERS
NF EN 14490 : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
DIN EN 13282-1 E : 2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 14490 E : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
API 10A : 2011 SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING
I.S. EN 12004-2:2017 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
DD ENV 13282:2000 Hydraulic road binders. Composition, specifications and conformity criteria
UNI EN 14490 : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
BS EN ISO 10426-1:2009 Petroleum and natural gas industries. Cements and materials for well cementing Specification
I.S. EN 13282-2:2015 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
CEN/TR 15840:2009 Evaluation of conformity of fly ash for concrete - Guidelines for the application of EN 450-2
UNE-EN 13282-1:2013 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
UNI EN 459-2 : 2010 BUILDING LIME - PART 2: TEST METHODS
I.S. EN 15191:2009 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
I.S. EN 14490:2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
DIN EN 14498 E : 2004 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - VOLUME AND WEIGHT CHANGES OF INJECTION PRODUCTS AFTER AIR DRYING AND WATER STORAGE CYCLES
DIN EN 14496 E : 2017 GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
DIN EN 459-2:2010-12 Building lime - Part 2: Test methods
DIN EN 14679 E : 2005 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
DIN EN 14647 E : 2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 13872:2004-04 Method of test for smoothing and/or levelling compounds - Determination of shrinkage
DIN EN 12808-4:2009-10 Grouts for tiles - Part 4: Determination of shrinkage
BS EN 12617-4:2002 Products and systems for the protection and repair of concrete structures. Test methods Determination of shrinkage and expansion
UNE-EN 196-10:2016 Methods of testing cement - Part 10: Determination of the water-soluble chromium (VI) content of cement
BS EN 934-5:2007 Admixtures for concrete, mortar and grout Admixtures for sprayed concrete. Definitions, requirements, conformity, marking and labelling
BS EN 13263-1 : 2005 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
BS EN 196-9:2010 Methods of testing cement Heat of hydration. Semi-adiabatic method
BS EN 1062-7:2004 Paints and varnishes. Coating materials and coating systems for exterior masonry and concrete Determination of crack bridging properties
BS EN 1744-1 : 2009 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
BS EN 12808-2:2008 Grouts for tiles Determination of resistance to abrasion
UNI EN 197-2 : 2014 CEMENT - PART 2: CONFORMITY EVALUATION
BS EN 450:1995 Fly ash for concrete. Definitions, requirements and quality control
BS EN 13687-4:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility Dry thermal cycling
BS EN 12878:2014 Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test
BS EN 480-1:2014 Admixtures for concrete, mortar and grout. Test methods Reference concrete and reference mortar for testing
BS EN 12808-5:2008 Grouts for tiles Determination of water absorption
BS EN 13395-1:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability Test for flow of thixotropic mortars
UNE-EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
BS EN 1015-2:1999 Methods of test for mortar for masonry Bulk sampling of mortars and preparation of test mortars
BS EN 13851:2003 Methods of test for hydraulic setting floor smoothing and/or levelling compounds. Determination of flexural and compressive strength
BS EN 13395-2:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability Test for flow of grout or mortar
BS EN 13584:2003 Products and systems for the protection and repair of concrete structures. Test methods. Determination of creep in compression for repair products
BS EN 13295:2004 Products and systems for the protection and repair of concrete structures.Test methods. Determination of resistance to carbonation
UNE-EN 1744-1:2010 Tests for chemical properties of aggregates - Part 1: Chemical analysis
I.S. EN 197-2:2014 CEMENT - PART 2: CONFORMITY EVALUATION
CEN/TR 14245:2014 Cement - Guidelines for the application of EN 197-2 Conformity Evaluation
BS EN 13057:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of resistance of capillary absorption
BS EN 15184:2006 Products and systems for the protection and repair of concrete structures. Test methods. Shear adhesion of coated steel to concrete (pull-out test)
BS EN 14679:2005 Execution of special geotechnical works. Deep mixing
BS EN 1008:2002 Mixing water for concrete. Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
BS EN 1937:1999 Test method for hydraulic setting floor smoothing and/or levelling compounds. Standard mixing procedures
DIN EN 14944-1:2006-07 Influence of cementitious products on water intended for human consumption - Test methods - Part 1: Influence of factory made cementitious products on organoleptic parameters
UNE-EN 14227-4:2014 Hydraulically bound mixtures - Specifications - Part 4: Fly ash for hydraulically bound mixtures
BS EN 1771:2004 Products and systems for the protection and repair of concrete structures. Test methods. Determination of injectability and splitting test
UNE-EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
BS EN 14216:2015 Cement. Composition, specifications and conformity criteria for very low heat special cements
UNE-EN 450-1:2013 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
UNE-EN 196-3:2017 Methods of testing cement - Part 3: Determination of setting times and soundness
DIN EN 480-5:2005-12 Admixtures for concrete, mortar and grout - Test methods - Part 5: Determination of capillary absorption
DIN EN 13851:2004-02 METHODS OF TEST FOR HYDRAULIC SETTING FLOOR SMOOTHING AND/OR LEVELLING COMPOUNDS - DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
EN 14679:2005/AC:2006 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
EN 450-1:2012 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
EN 1542:1999 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
EN 15368:2008+A1:2010 Hydraulic binder for non-structural applications - Definition, specifications and conformity criteria
EN 450-2:2005 Fly ash for concrete - Part 2: Conformity evaluation
EN 450 : 1994 FLY ASH FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND QUALITY CONTROL
EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, assessment and verification of constancy of performance, classification and marking
EN 15184:2006 Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)
EN 1744-1:2009+A1:2012 Tests for chemical properties of aggregates - Part 1: Chemical analysis
EN 16622:2015 Silica-calcium fume for concrete - Definitions, requirements and conformity criteria
EN 480-14:2006 Admixtures for concrete, mortar and grout - Test methods - Part 14: Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
EN 1771:2004/AC:2005 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF INJECTABILITY AND SPLITTING TEST
EN 14490:2010 Execution of special geotechnical works - Soil nailing
EN 1937:1999 Test method for hydraulic setting floor smoothing and/or levelling compounds - Standard mixing procedures
EN 14016-2 : 2004 BINDERS FOR MAGNESITE SCREEDS - CAUSTIC MAGNESIA AND MAGNESIUM CHLORIDE - PART 2: TEST METHODS
EN 13892-1:2002 Methods of test for screed materials - Part 1: Sampling, making and curing specimens for test
EN 13687-3:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 3: Thermal cycling without de-icing salt impact
ENV 197-1 : 1992 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA - COMMON CEMENTS
EN 445:2007 Grout for prestressing tendons - Test methods
EN 15167-2:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 2: Conformity evaluation
EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
EN 196-3:2016 Methods of testing cement - Part 3: Determination of setting times and soundness
EN 15743:2010+A1:2015 Supersulfated cement - Composition, specifications and conformity criteria
EN 12878:2014 Pigments for the colouring of building materials based on cement and/or lime - Specifications and methods of test
EN 14496:2017 Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods
EN 13687-1:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 1: Freeze-thaw cycling with de-icing salt immersion
EN 14647:2005/AC:2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 13687-2:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock)
EN 14944-3:2007 Influence of cementitious products on water intended for human consumption - Test methods - Part 3: Migration of substances from factory-made cementititous products
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
EN 13687-4:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 4: Dry thermal cycling
EN 14227-4:2013 Hydraulically bound mixtures - Specifications - Part 4: Fly ash for hydraulically bound mixtures
EN 15183:2006 Products and systems for the protection and repair of concrete structures - Test methods - Corrosion protection test
EN 197-4:2004 Cement - Part 4: Composition, specifications and conformity criteria for low early strength blastfurnace cements
EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
EN 480-2:2006 Admixtures for concrete, mortar and grout - Test methods - Part 2: Determination of setting time
EN 196-10:2016 Methods of testing cement - Part 10: Determination of the water-soluble chromium (VI) content of cement
EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria
EN 14944-1:2006 Influence of cementitious products on water intended for human consumption - Test methods - Part 1: Influence of factory made cementitious products on organoleptic parameters
EN 480-13:2015 Admixtures for concrete, mortar and grout - Test methods - Part 13: Reference masonry mortar for testing mortar admixtures
EN 14498:2004 Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles
EN 13872:2004 Methods of test for hydraulic setting floor smoothing and/or levelling compounds - Determination of dimensional change
EN 934-5:2007 Admixtures for concrete, mortar and grout - Part 5: Admixtures for sprayed concrete - Definitions, requirements, conformity, marking and labelling
EN 13851 : 2003 METHODS OF TEST FOR HYDRAULIC SETTING FLOOR SMOOTHING AND/OR LEVELLING COMPOUNDS - DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
EN 15191:2009 Precast concrete products - Classification of glassfibre reinforced concrete performance
EN 14016-1:2004 Binders for magnesite screeds - Caustic magnesia and magnesium chloride - Part 1: Definitions, requirements
EN 480-1:2014 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
EN 13892-2 : 2002 METHODS OF TEST FOR SCREED MATERIALS - PART 2: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
PREN 14944-3 : DRAFT 2015 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 3: MIGRATION OF SUBSTANCES FROM FACTORY-MADE CEMENTITIOUS PRODUCTS
BS EN 13282-3:2013 Hydraulic road binders Conformity evaluation
PREN 14944-1 : DRAFT 2015 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF MIGRATION FROM FACTORY MADE CEMENTITIOUS PRODUCTS ON THE ORGANOLEPTIC PARAMETERS
10/30200038 DC : 0 BS EN 13282-2 - HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
PD CEN/TR 16912:2016 Guidelines for a procedure to support the European standardization of cements
08/30189560 DC : 0 BS EN 12808-4 - GROUTS FOR TILES - PART 4: DETERMINATION OF SHRINKAGE
I.S. EN 197-4:2004 CEMENT - PART 4: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW EARLY STRENGTH BLASTFURNACE CEMENTS
01/103361 DC : DRAFT APR 2001 PREN 413-1 - MASONRY CEMENT - PART 1: SPECIFICATION
12/30256100 DC : 0 BS EN 12878 - PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
BS EN 15191:2009 Precast concrete products. Classification of glassfibre reinforced concrete performance
09/30195262 DC : 0 BS ISO 12439 - MIXING WATER FOR CONCRETE
11/30251426 DC : DRAFT OCT 2011 BS EN 480-15 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 15: REFERENCE CONCRETE AND METHOD FOR TESTING VISCOSITY MODIFYING ADMIXTURES
DIN EN 12004-2 E : 2017 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
BS EN 10298:2005 Steel tubes and fittings for onshore and offshore pipelines. Internal lining with cement mortar
09/30200445 DC : 0 BS EN 15191 - PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASS-FIBRE REINFORCED CONCRETE PERFORMANCES
05/30129415 DC : DRAFT FEB 2005 BS EN 480-1 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
BS EN 13282-1:2013 Hydraulic road binders Rapid hardening hydraulic road binders. Composition, specifications and conformity criteria
BS EN 13282-2:2015 Hydraulic road binders Normal hardening hydraulic road binders. Composition, specifications and conformity criteria
05/30130592 DC : DRAFT MAR 2005 BS EN 15167-1 - GROUND GRANULATED BLASTFURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
BS EN 14944-3:2007 Influence of cementitious products on water intended for human consumption. Test methods Migration of substances from factory-made cementitious products
05/19974131 DC : DRAFT JAN 2005 BS EN 480-14 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 14: MEASUREMENT OF CORROSION SUSCEPTIBILITY OF REINFORCING STEEL IN CONCRETE - POTENTIOSTATIC ELECTROCHEMICAL TEST METHOD
UNI EN 13282-1 : 2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 459-2:2010 Building lime - Part 2: Test methods
UNE-EN 14490:2013 Execution of special geotechnical works - Soil nailing
BS EN 13454-2:2003 Binders, composite binders and factory made mixtures or floor screeds based on calcium sulfate Test methods
UNE-EN 16506:2015 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
I.S. EN 13282-1:2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNE-EN 13282-2:2016 Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria
DIN EN 13454-2:2007-11 BINDERS, COMPOSITE BINDERS AND FACTORY MADE MIXTURES FOR FLOOR SCREEDS BASED ON CALCIUM SULFATE - PART 2: TEST METHODS
UNE-EN 12004-2:2017 Adhesives for ceramic tiles - Part 2: Test methods
I.S. EN 16506:2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
UNI EN 15368 : 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
15/30317324 DC : 0 BS EN 14944-3 - INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 3: MIGRATION OF SUBSTANCES FROM FACTORY-MADE CEMENTITIOUS PRODUCTS
17/30362692 DC : 0 BS EN 598 - COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS
UNI EN 15191 : 2010 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
ASTM D 7143 : 2017 : REDLINE Standard Practice for Emission Cells for the Determination of Volatile Organic Emissions from Indoor Materials/Products
ISO 13007-5:2015 Ceramic tiles Grouts and adhesives Part 5: Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
DIN EN ISO 16000-11:2006-06 Indoor air - Part 11: Determination of the emission of volatile organic compounds from building products and furnishing - Sampling, storage of samples and preparation of test specimens (ISO 16000-11:2006)
DIN EN 14944-1:2015-06 (Draft) INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF FACTORY MADE CEMENTITIOUS PRODUCTS ON ORGANOLEPTIC PARAMETERS
DIN EN 13295:2004-08 Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation
DIN EN 1062-7:2004-08 Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 7: Determination of crack bridging properties
BS EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking
BS EN 13872:2004 Method of test for smoothing and/or levelling compounds. Determination of dimensional change
BS EN 14016-2:2004 Binders for magnesite screeds. Caustic magnesia and magnesium chloride Test methods
BS EN 480-13:2015 Admixtures for concrete, mortar and grout. Test methods Reference masonry mortar for testing mortar admixtures
BS EN 15167-2:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout Conformity evaluation
BS EN 14944-1:2006 Influence of cementitious products on water intended for human consumption. Test methods Influence of factory made cementitious products on organoleptic parameters
BS EN 13892-2:2002 Methods of test for screed materials Determination of flexural and compressive strength
BS EN 13687-1:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility Freeze-thaw cycling with de-icing salt immersion
BS EN 1346:1999 Adhesives for tiles. Determination of open time
BS EN 12002:2008 Adhesives for tiles. Determination of transverse deformation for cementitious adhesives and grouts
BS EN 12618-1:2003 Products and systems for the protection and repair of concrete structures. Test methods Adhesion and elongation capacity of injection products with limited ductility
BS EN 14496:2005 Gypsum based adhesives for thermal/acoustic insulation composite panelsa nd plasterboards. Definitions, requirements and test methods
BS EN ISO 16000-11:2006 Indoor air Determination of the emission of volatile organic compounds from building products and furnishing. Sampling, storage of samples and preparation of test specimens
BS EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout Definitions, specifications and conformity criteria
BS EN 413-1:2011 Masonry cement Composition, specifications and conformity criteria
BS EN 196-10:2016 Methods of testing cement Determination of the water-soluble chromium (VI) content of cement
BS EN 197-4:2004 Cement Composition, specifications and conformity criteria for low early strength blastfurnace cements
BS EN 13687-5:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility Resistance to temperature shock
EN 12618-3:2004 Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of the adhesion of injection products, with or without thermal cycling - Slant shear method
CR 14245:2001 Guidelines for the application of EN 197-2 "Conformity Evaluation"
EN 1015-2:1998/A1:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 2: BULK SAMPLING OF MORTARS AND PREPARATION OF TEST MORTARS
EN 1008:2002 Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
EN 13395-2:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 2: Test for flow of grout or mortar
EN 12615:1999 Products and systems for the protection and repair of concrete structures - Test methods - Determination of slant shear strength
DIN EN 13892-2:2003-02 METHODS OF TEST FOR SCREED MATERIALS - PART 2: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH
EN 12190:1998 Products and systems for the protection and repair of concrete structures - Test methods - Determination of compressive strength of repair mortar
DIN EN 12004-2:2017-05 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
DIN EN 12618-1:2003-11 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - PART 1: ADHESION AND ELONGATION CAPACITY OF INJECTION PRODUCTS WITH LIMITED DUCTILITY
DIN EN 480-2:2006-11 Admixtures for concrete, mortar and grout - Test methods - Part 2: Determination of setting time
EN 10298:2005 Steel tubes and fittings for on shore and offshore pipelines - Internal lining with cement mortar
EN 13395-4:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 4: Application of repair mortar overhead
DIN EN 12808-2:2009-01 Grouts for tiles - Part 2: Determination of resistance to abrasion
EN 12808-3:2008 Grouts for tiles - Part 3: Determination of flexural and compressive strength
DIN EN 450-2:2005-05 Fly ash for concrete - Part 2: Conformity evaluation
EN 13282-2:2015 Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria
EN 13282-1:2013 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
EN 1308:2007 Adhesives for tiles - Determination of slip
EN 1347:2007 Adhesives for tiles - Determination of wetting capability
DIN EN 545:2011-09 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
DIN EN 196-3:2017-03 METHODS OF TESTING CEMENT - PART 3: DETERMINATION OF SETTING TIMES AND SOUNDNESS
DIN EN 10298:2005-12 Steel tubes and fittings for onshore and offshore pipelines - Internal lining with cement mortar
DIN EN 15184:2006-11 Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)
DIN EN 14498:2004-12 Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles; German version EN 14498:2004
DIN EN 12618-3:2004-11 Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of the adhesion of injection products, with or without thermal cycling - Slant shear method
EN 1346:2007 Adhesives for tiles - Determination of open time
EN 12004-2:2017 Adhesives for ceramic tiles - Part 2: Test methods
EN 13282-3:2015 Hydraulic road binders - Part 3: Conformity evaluation
DIN EN 450-1:2012-10 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
DIN EN 13892-1:2003-02 METHODS OF TEST FOR SCREED MATERIALS - PART 1: SAMPLING - MAKING AND CURING SPECIMENS FOR TESTING
DIN EN 15183:2006-11 Products and systems for the protection and repair of concrete structures - Test methods - Corrosion protection test
DIN EN 12808-5:2009-01 Grouts for tiles - Part 5: Determination of water absorption
ONORM EN 14944-1 : 2006 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF FACTORY MADE CEMENTITIOUS PRODUCTS ON ORGANOLEPTIC PARAMETERS
ONORM EN 14944-3 : 2008 INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 3: MIGRATION OF SUBSTANCES FROM FACTORY-MADE CEMENTITITOUS PRODUCTS

EN 196-7:2007 Methods of testing cement - Part 7: Methods of taking and preparing samples of cement
ISO 3310-1:2016 Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth
EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
EN ISO 1101:2017 Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
EN ISO 1302 : 2002 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION (ISO 1302:2002)
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
AS ISO 13007.5:2020 Ceramic tiles - Grouts and adhesives Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.