EN 30012-1 : 1993
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
19-03-2022
12-01-2013
Committees responsible
National foreword
Specification
Introduction
1. Scope
2. Normative references
3. Definitions
4. Requirements
4.1 General
4.2 Measuring equipment
4.3 Confirmation system
4.4 Periodic audit and review of the configuration
system
4.5 Planning
4.6 Uncertainty of measurement
4.7 Documented confirmation procedures
4.8 Records
4.9 Nonconforming measuring equipment
4.10 Confirmation labelling
4.11 Intervals of confirmation
4.12 Sealing for integrity
4.13 Use of outside products and services
4.14 Storage and handling
4.15 Traceability
4.16 Cumulative effect of uncertainties
4.17 Environmental conditions
4.18 Personnel
Annexes
A. (informative) Guidelines for the determination of
confirmation intervals for measuring equipment
A.1 Introduction
A.2 Initial choice of confirmation intervals
A.3 Methods of reviewing confirmation intervals
B. (informative) Bibliography
ALSO NUMBERED AS BS 5781: PART 1: 1992. Specifies the main features of the confirmation system to be used for a supplier's measuring equipment. Contains quality assurance requirements for a supplier to ensure that measurements are made with intended accuracy; also contains advice on the implementation of the requirements. Applies to: testing laboratories (including those providing a calibration service); to suppliers of services or products who operate in a quality system in which measurement is used to demonstrate compliance with specified requirements. Also includes detailed annexes.
| Committee |
CEN/CS F20
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS EN 30012-1:1994 | Identical |
| NEN ISO 10012-1 : 1994 | Identical |
| I.S. EN 30012-1:1994 | Identical |
| ISO 10012-1:1992 | Identical |
| NF EN 30012-1 : 1994 | Identical |
| UNI EN 30012-1 : 1994 | Identical |
| DIN ISO 10012-1:1992-08 | Identical |
| SNV NF EN 30012-1 : 1994 | Identical |
| UNE-EN 30012-1:1994 | Identical |
| NBN EN 30012-1 : 1994 | Identical |
| BS EN 60068-3-6:2002 | Environmental testing. Guidance Confirmation of the performance of temperature/humidity chambers |
| 01/714474 DC : DRAFT NOV 2001 | BS EN 14276-1 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| CEI EN 60761-1 : 2005 | EQUIPMENT FOR CONTINUOUS MONITORING RADIOACTIVITY IN GASEOUS EFFLUENTS - PART 1: GENERAL REQUIREMENTS |
| EN ISO 13938-2 : 1999 | TEXTILES - BURSTING PROPERTIES OF FABRICS - PART 2: PNEUMATIC METHOD FOR DETERMINATION OF BURSTING STRENGTH AND BURSTING DISTENSION |
| I.S. EN ISO 13938-2:1999 | TEXTILES - BURSTING PROPERTIES OF FABRICS - PART 2: PNEUMATIC METHOD FOR DETERMINATION OF BURSTING STRENGTH AND BURSTING DISTENSION |
| BS EN 12127:1998 | Textiles. Fabrics. Determination of mass per unit area using small samples |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| BS EN ISO 14111:1999 | Natural gas. Guidelines to traceability in analysis |
| BS EN ISO 5436-1:2001 | Geometrical Product Specifications (GPS). Surface texture: Profile method; Measurement standards Geometric product specifications (GPS). Surface texture. Profile method calibration. Measurement standards |
| EN ISO 12179:2000/AC:2008 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - CALIBRATION OF CONTACT (STYLUS) INSTRUMENTS |
| EN 60068-3-6:2002 | Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers |
| EN 12127:1997 | Textiles - Fabrics - Determination of mass per unit area using small samples |
| 05/30135474 DC : DRAFT JUNE 2005 | BS 600 - A GUIDE TO THE APPLICATION OF STATISTICAL METHODS TO QUALITY AND STANDARDIZATION |
| 04/30118456 DC : DRAFT NOV 2004 | EN 14704-3 - DETERMINATION OF ELASTICITY OF FABRICS - PART 3: NARROW FABRICS |
| I.S. EN 60068-3-5:2002 | ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS |
| I.S. EN 60068-3-6:2002 | ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS |
| BIS IS/ISO 13935-1 : 1999 | TEXTILES - SEAM TENSILE PROPERTIES OF FABRICS AND MADE-UP TEXTILE ARTICLES - PART 1: DETERMINATION OF MAXIMUM FORCE TO SEAM RUPTURE USING THE STRIP METHOD |
| I.S. EN ISO 13938-1:1999 | TEXTILES - BURSTING PROPERTIES OF FABRICS - PART 1 - HYDRAULIC METHOD FOR DETERMINATION OF BURSTING STRENGTH AND BURSTING DISTENSION |
| 03/108254 DC : DRAFT MAY 2003 | PREN 14704-1 - DETERMINATION OF THE ELASTICITY OF FABRICS - PART 1: STRIP TESTS |
| CEI EN 60068-3-5 : 2002 | ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS |
| CEI EN 60068-3-6 : 2002 | ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS |
| 05/30066730 DC : DRAFT JAN 2005 | PREN 14704-2 - ELASTICITY OF FABRICS - PART 2: MULTIAXIAL TESTS |
| BS EN ISO 13938-2:1999 | Textiles. Bursting properties of fabrics Pneumatic method for determination of bursting strength and bursting distension |
| EN 100114-1 : 1996 | RULE OF PROCEDURE - QUALITY ASSESSMENT PROCEDURES - PART 1: CECC REQUIREMENTS FOR THE APPROVAL OF AN ORGANIZATION |
| BIS IS/ISO 13935-2 : 1999 | TEXTILES - SEAM TENSILE PROPERTIES OF FABRICS AND MADE-UP TEXTILE ARTICLES - PART 2: DETERMINATION OF MAXIMUM FORCE TO SEAM RUPTURE USING THE GRAB METHOD |
| NFG 30 105 : 2002 XP | SECURITE DES VETEMENTS D'ENFANTS - CORDONS OU LIENS DE SERRAGE |
| I.S. EN 60761-1:2004 | EQUIPMENT FOR CONTINUOUS MONITORING RADIOACTIVITY IN GASEOUS EFFLUENTS - PART 1: GENERAL REQUIREMENTS |
| BS EN ISO 13938-1:1999 | Textiles. Bursting properties of fabrics Hydraulic method for determination of bursting strength and bursting distension |
| ISO 13938-1:1999 | Textiles Bursting properties of fabrics Part 1: Hydraulic method for determination of bursting strength and bursting distension |
| BS EN 13486:2002 | Temperature recorders and thermometers for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen food and ice cream. Periodic verification |
| ISO 13938-2:1999 | Textiles Bursting properties of fabrics Part 2: Pneumatic method for determination of bursting strength and bursting distension |
| BS EN 45012:1998 | General requirements for bodies operating assessment and certification/registration of quality systems |
| ISO 12179:2000 | Geometrical Product Specifications (GPS) Surface texture: Profile method Calibration of contact (stylus) instruments |
| EN ISO 13938-1 : 1999 | TEXTILES - BURSTING PROPERTIES OF FABRICS - PART 1: HYDRAULIC METHOD FOR DETERMINATION OF BURSTING STRENGTH AND BURSTING DISTENSION |
| I.S. EN 45012:1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| BS EN 60761-1:2004 | Equipment for continuous monitoring radioactivity in gaseous effluents General requirements |
| I.S. EN 100114-1:1997 | RULE OF PROCEDURE - QUALITY ASSESSMENT PROCEDURES - PART 1: CECC REQUIREMENTS FOR THE APPROVAL OF AN ORGANIZATION |
| BS EN ISO 12179:2001 | Geometrical product specifications (GPS). Surface texture. Profile method. Calibration of contact (stylus) instruments |
| EN 60068-3-5:2002 | Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers |
| EN 13486:2001 | Temperature recorders and thermometers for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen food and ice cream - Periodic verification |
| EN 60761-1:2004 | Equipment for continuous monitoring radioactivity in gaseous effluents - Part 1: General requirements |
| I.S. EN 13486:2002 | TEMPERATURE RECORDERS AND THERMOMETERS FOR THE TRANSPORT, STORAGE AND DISTRIBUTION OF CHILLED, FROZEN, DEEP-FROZEN/QUICK-FROZEN FOOD AND ICE CREAM - PERIOD VERIFICATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.