EN 378-1:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria
Superseded date
05-11-2020
Published date
30-11-2016
Publisher
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Classification
6 Quantity of refrigerant
7 Space volume calculations
Annex A (informative) - Equivalent terms in English,
French and German
Annex B (informative) - Total equivalent warming
impact (TEWI)
Annex C (normative) - Refrigerant charge limit
requirements
Annex D (informative) - Protection for people who
are inside cold rooms
Annex E (normative) - Safety classification and
information about refrigerants
Annex F (normative) - Special requirements for ice rinks
Annex G (informative) - Potential hazards for
refrigerating systems
Annex H (informative) - Calculation examples related
to C.2 and C.3
Bibliography
This European Standard specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment and establishes procedures for the operation, maintenance and repair of refrigerating systems and the recovery of refrigerants.The term "refrigerating system" used in this European Standard includes heat pumps.This part of EN 378 specifies the classification and selection criteria applicable to refrigerating systems. These classification and selection criteria are used in parts 2, 3 and 4.This standard applies:a)to refrigerating systems, stationary or mobile, of all sizes except to vehicle air conditioning systems covered by a specific product standard e.g. ISO 13043;b)to secondary cooling or heating systems;c)to the location of the refrigerating systems;d)to replaced parts and added components after adoption of this standard if they are not identical in function and in the capacity;Systems using refrigerants other than those listed in Annex E of this European Standard are not covered by this standard.Annex C specifies how to determine the amount of refrigerant permitted in a given space, which when exceeded, requires additional protective measures to reduce the risk.Annex E specifies criteria for safety and environmental considerations of different refrigerants used in refrigeration and air conditioning.This standard is not applicable to refrigerating systems and heat pumps which were manufactured before the date of its publication as a European Standard except for extensions and modifications to the system which were implemented after publication.This standard is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for existing stationary systems, being transferred to and operated on another site.This standard also applies in the case of the conversion of a system to another refrigerant type, in which case conformity to the relevant clauses of parts 1 to 4 of the standard shall be assessed.Product family standards dealing with the safety of refrigerating systems takes precedence over horizontal and generic standards covering the same subject.
| Committee |
CEN/TC 182
|
| DevelopmentNote |
Supersedes PREN 378-1. (12/2016)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 378-1:2016 | Identical |
| PN EN 378-1 : 2017 | Identical |
| NBN EN 378-1 : 2008 + A2 2012 | Identical |
| I.S. EN 378-1:2016 | Identical |
| UNI EN 378-1:2017 | Identical |
| NF EN 378-1 : 2017 | Identical |
| NEN EN 378-1 : 2016 | Identical |
| SN EN 378-1:2017 | Identical |
| UNE-EN 378-1:2017 | Identical |
| NS EN 378-1 : 2016 | Identical |
| DIN EN 378-1:2014-02 (Draft) | Identical |
| UNE-EN 378-1:2008 | Identical |
| ONORM EN 378-1 : 2017 | Identical |
| ONORM EN 378-1 : 2018 | Identical |
| UNI EN 378-1 : 2012 | Identical |
| SS-EN 378-1:2016 | Identical |
| DIN EN 378-1:2018-04 | Identical |
| DIN EN 378-1:2012-08 | Identical |
| DIN EN 1010-2:2011-05 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 2: Printing and varnishing machines including pre-press machinery (includes Amendment A1:2010) |
| 12/30258153 DC : DRAFT MAR 2012 | BS EN 12900 - REFRIGERANT COMPRESSORS - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| I.S. EN 16084:2011 | REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| 03/302503 DC : DRAFT FEB 2003 | BS EN 14276-2 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| I.S. EN 16902:2016 | COMMERCIAL BEVERAGE COOLERS - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| 15/30325845 DC : 0 | BS EN 16901 - ICE-CREAM FREEZERS - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| BS ISO 19659-1:2017 | Railway applications. Heating, ventilation and air conditioning systems for rolling stock Terms and definitions |
| 16/30335111 DC : 0 | BS EN 12178 - REFRIGERATING SYSTEMS AND HEAT PUMPS - LIQUID LEVEL INDICATING DEVICES - REQUIREMENTS, TESTING AND MARKING |
| UNE-EN 16825:2017 | Refrigerated storage cabinets and counters for professional use - Classification, requirements and test conditions |
| BS ISO 12643-1:2009 | Graphic technology. Safety requirements for graphic technology equipment and systems General requirements |
| DIN 2405:2003-01 | Pipelines in refrigerating systems and cooling equipment - Marking |
| PREN 13136 : DRAFT 2011 | REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| 13/30291013 DC : 0 | BS EN ISO 23953-2 - REFRIGERATED DISPLAY CABINETS - PART 2: CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| 15/30317315 DC : 0 | BS EN 16838 - REFRIGERATED DISPLAY SCOOPING CABINETS FOR GELATO - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| UNI EN ISO 15138 : 2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - OFFSHORE PRODUCTION INSTALLATIONS - HEATING, VENTILATION AND AIR-CONDITIONING |
| I.S. EN 16838:2016 | REFRIGERATED DISPLAY SCOOPING CABINETS FOR GELATO - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| PREN 14276-2 : DRAFT 2017 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| I.S. EN 378-2:2016 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 2: DESIGN, CONSTRUCTION, TESTING, MARKING AND DOCUMENTATION |
| PREN 15834 : DRAFT 2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| UNE-EN 16901:2018 | Ice-cream freezers - Classification, requirements and test conditions |
| BS EN 16838:2016 | Refrigerated display scooping cabinets for gelato. Classification, requirements and test conditions |
| I.S. EN 378-4:2016 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 4: OPERATION, MAINTENANCE, REPAIR AND RECOVERY |
| EN 378-3:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| EN 12309-2:2015/AC:2015 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 2: SAFETY |
| DIN EN 13136:2013-12 | REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| UNE-EN 378-2:2017 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| BS EN 61010-2-011:2017 | Safety requirements for electrical equipment for measurement, control, and laboratory use Particular requirements for refrigerating equipment |
| BS EN 13136 : 2013 | REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| I.S. EN 14276-1:2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| DIN EN 1736:2009-02 | REFRIGERATING SYSTEMS AND HEAT PUMPS - FLEXIBLE PIPE ELEMENTS, VIBRATION ISOLATORS, EXPANSION JOINTS AND NON-METALLIC TUBES - REQUIREMENTS, DESIGN AND INSTALLATION |
| EN 1010-2:2006+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 2: Printing and varnishing machines including pre-press machinery |
| EN 61010-2-012:2016 | Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditioning equipment |
| EN 12900:2013 | Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data |
| EN 12178:2016 | Refrigerating systems and heat pumps - Liquid level indicating devices - Requirements, testing and marking |
| I.S. EN 12284:2003 | REFRIGERATING SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| EN 12693:2008 | Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors |
| 96/700629 DC : DRAFT JAN 1996 | PREN 12284 REFRIGERATION SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| BS EN 16901:2016 | Ice-cream freezers. Classification, requirements and test conditions |
| 03/321181 DC : DRAFT DEC 2003 | EN 12900 - REFRIGERANT COMPRESSORS - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURERS PERFORMANCE DATA |
| 09/30201361 DC : 0 | BS ISO 12643-2 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 2: PRESS EQUIPMENT AND SYSTEMS |
| BS EN 16084:2011 | Refrigerating systems and heat pumps. Qualification of tightness of components and joints |
| DIN EN 12693:2016-10 (Draft) | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| 11/30248111 DC : 0 | BS EN 13136 - REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| 16/30346580 DC : 0 | BS EN 13771-2 - COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| BS EN ISO 8230-1:2008 | Safety requirements for dry-cleaning machines Common safety requirements |
| PREN 13215 : DRAFT 2015 | CONDENSING UNITS FOR REFRIGERATION - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| PREN 13771-1 : DRAFT 2014 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| 04/30110212 DC : DRAFT MAR 2004 | ISO 12648 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR PRINTING PRESS SYSTEMS |
| BS ISO 12643-2:2010 | Graphic technology. Safety requirements for graphic technology equipment and systems Prepress and press equipment and systems |
| BS EN 12693:2008 | Refrigerating systems and heat pumps. Safety and environmental requirements. Positive displacement refrigerant compressors |
| 03/301505 DC : DRAFT JAN 2003 | ISO 23953-2 - REFRIGERATED DISPLAY CABINETS - PART 2: CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| CEN Guide 14:2010 | Common policy guidance for addressing standardisation on qualification of professions and personnel |
| DIN EN 16084:2011-07 | REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| BIS IS/ISO 12643-2 : 2010 | GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 2: PREPRESS AND PRESS EQUIPMENT AND SYSTEMS |
| I.S. EN 16901:2016 | ICE-CREAM FREEZERS - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| I.S. EN 16825:2016 | REFRIGERATED STORAGE CABINETS AND COUNTERS FOR PROFESSIONAL USE - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| EN 16838:2016 | Refrigerated display scooping cabinets for gelato - Classification, requirements and test conditions |
| I.S. EN 13136:2013 | REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| BS EN 16825:2016 | Refrigerated storage cabinets and counters for professional use. Classification, requirements and test conditions |
| DIN EN 12284:2004-01 | Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
| DIN EN 13215:2015-07 (Draft) | CONDENSING UNITS FOR REFRIGERATION - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| DIN EN 12900:2013-10 | REFRIGERANT COMPRESSORS - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| DIN EN 13771-1:2015-01 (Draft) | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| DIN EN 13771-2:2016-11 (Draft) | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| BS EN 1736:2008 | Refrigerating systems and heat pumps. Flexible pipe elements, vibration isolators, expansion joints and non-metallic tubes. Requirements, design and installation |
| I.S. EN ISO 23953-2:2015 | REFRIGERATED DISPLAY CABINETS - PART 2: CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS (ISO 23953-2:2015) |
| DIN EN ISO 23953-2:2016-03 | REFRIGERATED DISPLAY CABINETS - PART 2: CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS (ISO 23953-2:2015) |
| I.S. EN 13732:2013 | FOOD PROCESSING MACHINERY - BULK MILK COOLERS ON FARMS - REQUIREMENTS FOR PERFORMANCE, SAFETY AND HYGIENE |
| I.S. EN 13313:2010 | REFRIGERATING SYSTEMS AND HEAT PUMPS - COMPETENCE OF PERSONNEL |
| I.S. EN 378-3:2016 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - PART 3: INSTALLATION SITE AND PERSONAL PROTECTION |
| I.S. EN 12178:2016 | REFRIGERATING SYSTEMS AND HEAT PUMPS - LIQUID LEVEL INDICATING DEVICES - REQUIREMENTS, TESTING AND MARKING |
| I.S. EN 13771-2:2017 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| I.S. EN 13771-1:2016 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| I.S. EN 12309-2:2015 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 2: SAFETY |
| NF EN 14276-1 : 2006 + A1 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| I.S. EN 12900:2013 | REFRIGERANT COMPRESSORS - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| NF EN 14276-2 : 2007 + A1 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| 14/30313297 DC : 0 | BS EN 13771-1 - COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| UNI EN 12693 : 2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| 16/30300176 DC : 0 | BS ISO 19659-1 - RAILWAY APPLICATIONS - HEATING, VENTILATION AND AIR CONDITIONING SYSTEMS FOR ROLLING STOCK - PART 1: TERMS AND DEFINITIONS |
| I.S. EN ISO 15138:2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - OFFSHORE PRODUCTION INSTALLATIONS - HEATING, VENTILATION AND AIR-CONDITIONING |
| UNI EN 13136 : 2014 | REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| 13/30279156 DC : 0 | BS EN 6101-2-012 ED.1 - SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-012: PARTICULAR REQUIREMENTS FOR CLIMATIC AND ENVIRONMENTAL TESTING AND OTHER TEMPERATURE CONDITIONING EQUIPMENT |
| ISO 12648:2006 | Graphic technology Safety requirements for printing press systems |
| 17/30351224 DC : 0 | BS EN 14276-1 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| UNE-EN 16838:2017 | Refrigerated display scooping cabinets for gelato - Classification, requirements and test conditions |
| BS EN 1010-2 : 2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 2: PRINTING AND VARNISHING MACHINES INCLUDING PRE-PRESS MACHINERY |
| UNI EN ISO 8230-1 : 2009 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| 05/30132431 DC : DRAFT APR 2005 | EN 13771-2 - COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| 08/30156074 DC : DRAFT APR 2008 | BS EN 1012-3 - COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
| CSA C22.2 No. 61010-2-012 : 2017 | SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 2-012: PARTICULAR REQUIREMENTS FOR CLIMATIC AND ENVIRONMENTAL TESTING AND OTHER TEMPERATURE CONDITIONING EQUIPMENT |
| BS ISO 12648:2006 | Graphic technology. Safety requirements for printing press systems |
| 08/30183861 DC : DRAFT SEP 2008 | BS EN 13732 - FOOD PROCESSING MACHINERY - BULK MILK COOLERS ON FARM - REQUIREMENTS FOR PERFORMANCE, SAFETY AND HYGIENE |
| 15/30315949 DC : 0 | BS EN 16825 - COMMERCIAL SERVICE REFRIGERATED CABINETS AND COUNTERS INTENDED FOR USE IN COMMERCIAL KITCHENS - DEFINITION OF PERFORMANCE CHARACTERISTICS AND ENERGY CONSUMPTION |
| ISO 12643-2:2010 | Graphic technology — Safety requirements for graphic technology equipment and systems — Part 2: Prepress and press equipment and systems |
| PREN 12178 : DRAFT 2016 | REFRIGERATING SYSTEMS AND HEAT PUMPS - LIQUID LEVEL INDICATING DEVICES - REQUIREMENTS, TESTING AND MARKING |
| I.S. EN ISO 8230-1:2008 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| UNE-EN 16084:2011 | Refrigerating systems and heat pumps - Qualification of tightness of components and joints |
| ISO 12649:2004 | Graphic technology Safety requirements for binding and finishing systems and equipment |
| ISO 12643-1:2009 | Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements |
| DIN EN 12178:2016-05 (Draft) | REFRIGERATING SYSTEMS AND HEAT PUMPS - LIQUID LEVEL INDICATING DEVICES - REQUIREMENTS, TESTING AND MARKING |
| DIN EN 15450 E : 2007 | HEATING SYSTEMS IN BUILDINGS - DESIGN OF HEAT PUMP HEATING SYSTEMS |
| DIN EN 14276-2:2011-05 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| DIN EN 14276-1:2011-05 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| BS EN 378-4:2016 | Refrigerating systems and heat pumps. Safety and environmental requirements Operation, maintenance, repair and recovery |
| UNE-EN 61010-2-011:2017 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment |
| UNE-EN 378-3:2017 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| EN 14276-1:2020 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| DIN EN 12309-2 E : 2016 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 2: SAFETY |
| UNI EN 14276-2 : 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| UNI EN 14276-1 : 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| I.S. EN 13215:2016 | CONDENSING UNITS FOR REFRIGERATION - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| EN 13215:2016 | Condensing units for refrigeration - Rating conditions, tolerances and presentation of manufacturer's performance data |
| EN ISO 8230-1:2008 | Safety requirements for dry-cleaning machines - Part 1: Common safety requirements (ISO 8230-1:2008) |
| UNI EN 1010-2 : 2010 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 2: PRINTING AND VARNISHING MACHINES INCLUDING PRE-PRESS MACHINERY |
| UNI EN 13313 : 2011 | REFRIGERATING SYSTEMS AND HEAT PUMPS - COMPETENCE OF PERSONNEL |
| UNI EN 1736 : 2009 | Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators, expansion joints and non- metallic tubes - Requirements, design and installation |
| UNI EN 12900 : 2013 | REFRIGERANT COMPRESSORS - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| 01/714474 DC : DRAFT NOV 2001 | BS EN 14276-1 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| 13/30279151 DC : 0 | BS EN 6101-2-011 ED.1 - SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-011: PARTICULAR REQUIREMENTS FOR REFRIGERATED EQUIPMENT |
| 08/30190505 DC : 0 | BS ISO 12643-1 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| 06/30127203 DC : DRAFT OCT 2006 | ISO 15138 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - OFFSHORE PRODUCTION INSTALLATIONS - HEATING, VENTILATION AND AIR CONDITIONING |
| BS EN 16902:2016 | Commercial beverage coolers. Classification, requirements and test conditions |
| 08/30175649 DC : DRAFT APR 2008 | BS EN 1736 - REFRIGERATING SYSTEMS AND HEAT PUMPS - FLEXIBLE PIPE ELEMENTS, VIBRATION ISOLATORS, EXPANSION JOINTS AND NON-METALLIC TUBES - REQUIREMENTS, DESIGN AND INSTALLATION |
| 15/30323331 DC : 0 | BS EN 13215 - CONDENSING UNITS FOR REFRIGERATION - RATING CONDITIONS, TOLERANCES AND PRESENTATION OF MANUFACTURER'S PERFORMANCE DATA |
| NF EN 16084 : 2011 | REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| BS EN 61010-2-012:2016 | Safety requirements for electrical equipment for measurement, control and laboratory use Particular requirements for climatic and environmental testing and other temperature conditioning equipment |
| UNI EN 16084 : 2011 | REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| DIN EN ISO 8230-1:2009-05 | SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 1: COMMON SAFETY REQUIREMENTS |
| BS EN ISO 15138:2007 | Petroleum and natural gas industries. Offshore production installations. Heating, ventilation and air-conditioning |
| I.S. EN 61010-2-012:2016 | SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 2-012: PARTICULAR REQUIREMENTS FOR CLIMATIC AND ENVIRONMENTAL TESTING AND OTHER TEMPERATURE CONDITIONING EQUIPMENT |
| EN 378-2:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| 17/30351221 DC : 0 | BS EN 14276-2 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| EN ISO 15138:2007 | Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007) |
| I.S. EN 12693:2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| DIN EN 13732:2013-10 | Food processing machinery - Bulk milk coolers on farms - Requirements for performance, safety and hygiene |
| DIN EN 13771-1 E : 2017 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| DIN EN 13771-2:2017-11 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| BS EN 12178:2003 | Refrigerating systems and heat pumps. Liquid level indicating devices. Requirements, testing and marking |
| ISO 8230-1:2008 | Safety requirements for dry-cleaning machines Part 1: Common safety requirements |
| BS EN 12284:2003 | Refrigerating systems and heat pumps. Valves. Requirements, testing and marking |
| IEC 61010-2-011:2016 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment |
| BS EN 13313:2001 | Refrigerating systems and heat pumps. Competence of personnel |
| UNE-EN 12900:2014 | Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data |
| BS EN 13215:2016 | Condensing units for refrigeration. Rating conditions, tolerances and presentation of manufacturer\'s performance data |
| BS EN 14276-2 : 2007 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| UNE-EN ISO 23953-2:2016 | Refrigerated display cabinets - Part 2: Classification, requirements and test conditions (ISO 23953-2:2015) |
| UNE-EN 378-4:2017 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| UNE-EN 13313:2011 | Refrigerating systems and heat pumps - Competence of personnel |
| BS EN 12900:2013 | Refrigerant compressors. Rating conditions, tolerances and presentation of manufacturer\'s performance data |
| BS EN 441-2:1995 | Refrigerated display cabinets General mechanical and physical requirements |
| UNE-EN 13771-1:2017 | Compressors and condensing units for refrigeration - Performance testing and test methods - Part 1: Refrigerant compressors |
| DIN EN 12309-2:2016-04 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 2: SAFETY |
| I.S. EN 14276-2:2007 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| EN 14276-1:2006+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| BS EN 14276-1 : 2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| BS EN 378-2:2016 | Refrigerating systems and heat pumps. Safety and environmental requirements Design, construction, testing, marking and documentation |
| ISO 23953-2:2015 | Refrigerated display cabinets — Part 2: Classification, requirements and test conditions |
| EN 14276-2:2007+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements |
| BS EN 378-3:2016 | Refrigerating systems and heat pumps. Safety and environmental requirements Installation site and personal protection |
| BS EN ISO 23953-2:2015 | Refrigerated display cabinets Classification, requirements and test conditions |
| UNE-EN 12309-2:2015 | Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 2: Safety |
| UNE-EN 13215:2017 | Condensing units for refrigeration - Rating conditions, tolerances and presentation of manufacturer's performance data |
| UNE-EN 12178:2017 | Refrigerating systems and heat pumps - Liquid level indicating devices - Requirements, testing and marking |
| EN 1736:2008 | Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators, expansion joints and non-metallic tubes - Requirements, design and installation |
| EN 16825:2016 | Refrigerated storage cabinets and counters for professional use - Classification, requirements and test conditions |
| EN 441-2 : 1994 | REFRIGERATED DISPLAY CABINETS - GENERAL MECHANICAL AND PHYSICAL REQUIREMENTS |
| EN ISO 23953-2:2015 | Refrigerated display cabinets - Part 2: Classification, requirements and test conditions (ISO 23953-2:2015) |
| EN 13771-1:2016 | Compressors and condensing units for refrigeration - Performance testing and test methods - Part 1: Refrigerant compressors |
| EN 378-4:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| EN 15450:2007 | Heating systems in buildings - Design of heat pump heating systems |
| EN 16084:2011 | Refrigerating systems and heat pumps - Qualification of tightness of components and joints |
| EN 13771-2:2017 | Compressors and condensing units for refrigeration - Performance testing and test methods - Part 2: Condensing units |
| EN 13732:2013 | Food processing machinery - Bulk milk coolers on farms - Requirements for performance, safety and hygiene |
| EN 16901:2016 | Ice-cream freezers - Classification, requirements and test conditions |
| 08/30181467 DC : DRAFT JULY 2008 | BS EN 15834 - REFRIGERATING SYSTEMS AND HEAT PUMPS - QUALIFICATION OF TIGHTNESS OF COMPONENTS AND JOINTS |
| 03/301332 DC : DRAFT JAN 2003 | ISO 12649 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR BINDING AND FINISHING SYSTEMS AND EQUIPMENT |
| 09/30203034 DC : 0 | BS EN 13313 - REFRIGERATING SYSTEMS AND HEAT PUMPS - COMPETENCE OF PERSONNEL - COMPLEMENTARY ELEMENT |
| 17/30358655 DC : 0 | BS EN 13136 - REFRIGERATING SYSTEMS AND HEAT PUMPS - PRESSURE RELIEF DEVICES AND THEIR ASSOCIATED PIPING - METHODS FOR CALCULATION |
| 98/717506 DC : DRAFT DEC 1998 | PREN 13389 - FOOD PROCESSING MACHINERY - MIXERS WITH HORIZONTAL SHAFTS - SAFETY AND HYGIENE REQUIREMENTS |
| S.R. CEN GUIDE 14:2010 | COMMON POLICY GUIDANCE FOR ADDRESSING STANDARDIZATION ON QUALIFICATION OF PROFESSIONS AND PERSONNEL |
| I.S. EN 1010-2:2006 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 2: PRINTING AND VARNISHING MACHINES INCLUDING PRE-PRESS MACHINERY |
| UNE-EN 14276-2:2008 | Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements |
| BS ISO 12649:2004 | Graphic technology. Safety requirements for binding and finishing systems and equipment |
| 15/30325848 DC : 0 | BS EN 16902 - COMMERCIAL BEVERAGE COOLERS - CLASSIFICATION, REQUIREMENTS AND TEST CONDITIONS |
| UNE-EN 13136:2014 | Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation |
| PREN 14276-1 : DRAFT 2017 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| CSA C22.2 No. 61010-2-011 : 2017 | SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-011: PARTICULAR REQUIREMENTS FOR REFRIGERATING EQUIPMENT |
| ISO 19659-1:2017 | Railway applications — Heating, ventilation and air conditioning systems for rolling stock — Part 1: Terms and definitions |
| PREN 13771-2 : DRAFT 2016 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 2: CONDENSING UNITS |
| EN 13136:2013 | Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation |
| DIN EN 13313:2011-02 | Refrigerating systems and heat pumps - Competence of personnel |
| BS EN 13732:2013 | Food processing machinery. Bulk milk coolers on farms. Requirements for performance, safety and hygiene |
| BS EN 12309-2:2015 | Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW Safety |
| BS EN 13771-1:2016 | Compressors and condensing units for refrigeration. Performance testing and test methods Refrigerant compressors |
| BS EN 15450:2007 | Heating systems in buildings. Design of heat pump heating systems |
| BS EN 13771-2:2017 | Compressors and condensing units for refrigeration. Performance testing and test methods Condensing units |
| DIN EN 12693:2008-09 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| I.S. EN 61010-2-011:2017 | SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-011: PARTICULAR REQUIREMENTS FOR REFRIGERATING EQUIPMENT |
| EN 12284 : 2003 | REFRIGERATING SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| EN 13313:2010 | Refrigerating systems and heat pumps - Competence of personnel |
| DIN EN 13771-1:2017-04 | COMPRESSORS AND CONDENSING UNITS FOR REFRIGERATION - PERFORMANCE TESTING AND TEST METHODS - PART 1: REFRIGERANT COMPRESSORS |
| EN 61010-2-011:2017 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment |
| DIN EN 441-2:1995-01 | REFRIGERATED DISPLAY CABINETS - PART 2: GENERAL MECHANICAL AND PHYSICAL REQUIREMENTS |
| EN 16902:2016 | Commercial beverage coolers - Classification, requirements and test conditions |
| DIN EN 15450:2007-12 | Heating systems in buildings - Design of heat pump heating systems |
| UNE-EN 14276-1:2007 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| EN 60335-2-40:2003/A13:2012/AC:2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS |
| IEC 60335-2-24:2010+AMD1:2012+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers |
| EN 378-4:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| EN 378-3:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| EN 60335-2-89:2010/A2:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-89: PARTICULAR REQUIREMENTS FOR COMMERCIAL REFRIGERATING APPLIANCES WITH AN INCORPORATED OR REMOTE REFRIGERANT CONDENSING UNIT OR COMPRESSOR (IEC 60335-2-89:2010/A2:2015, MODIFIED) |
| ISO 5149:1993 | Mechanical refrigerating systems used for cooling and heating Safety requirements |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 60335-2-40:2013+AMD1:2016 CSV | Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditionersand dehumidifiers |
| EN 14276-1:2006+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| EN 60335-2-24:2010 | Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| EN ISO 14040:2006 | Environmental management - Life cycle assessment - Principles and framework (ISO 14040:2006) |
| EN 12263:1998 | Refrigerating systems and heat pumps - Safety switching devices for limiting the pressure - Requirements and tests |
| EN 14276-2:2007+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 13313:2010 | Refrigerating systems and heat pumps - Competence of personnel |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 817:2014 | Refrigerants Designation and safety classification |
| ISO 14040:2006 | Environmental management Life cycle assessment Principles and framework |
| EN 378-2:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| EN 16084:2011 | Refrigerating systems and heat pumps - Qualification of tightness of components and joints |
| IEC 60335-2-89:2010+AMD1:2012+AMD2:2015 CSV | Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant unit or compressor |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.