EN 3976:2006
Current
Current
The latest, up-to-date edition.
Aerospace series - Titanium and titanium alloys - Test method - Chemical analysis for the determination of hydrogen content
Published date
20-12-2006
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Health and safety
5 Principle
6 Testing requirements
7 Test report
Annex A (informative) Solid State Hot Extraction
under Vacuum Method
This standard specifies the requirements for chemical analysis using Inert Gas Fusion Thermal Conductivity Method for the determination of the hydrogen content of titanium and titanium alloys for aerospace applications.The method applies to hydrogen contents ranging from several micrograms per gram to several hundreds of micrograms per gram.It shall be applied when referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule.NOTEThe absolute method not used in routine inspection is solid state hot extraction under vacuum followed by measurement of volume and pressure. Due to its complexity, it is only summarized in Annex A.
| Committee |
ASD-STAN
|
| DevelopmentNote |
Supersedes PREN 3976. (04/2007)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 3976 : 2007 | Identical |
| I.S. EN 3976:2006 | Identical |
| NBN EN 3976 : 2007 | Identical |
| UNI EN 3976 : 2008 | Identical |
| SN EN 3976 : 2007 | Identical |
| PN EN 3976 : 2007 | Identical |
| BS EN 3976:2006 | Identical |
| NEN EN 3976 : 2007 | Identical |
| DIN EN 3976:2007-04 | Identical |
| NS EN 3976 : 1ED 2006 | Identical |
| UNE-EN 3976:2006 | Identical |
| UNI EN 4800-006 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| PREN 4800-006 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 6: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| PREN 4800-005 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 5: FORGING STOCK |
| PREN 4800-003 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 3: TUBE |
| I.S. EN 4800-002:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| UNI EN 4800-004 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE |
| UNI EN 4800-005 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| NF EN 4800-003 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE |
| NF EN 4800-006 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| NF EN 4800-002 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| NF EN 4800-005 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| BS EN 4800-006:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production forgings |
| I.S. EN 4800-005:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| 02/708860 DC : 0 | PREN 4800-1 - AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 1: PLATE, SHEET AND STRIP |
| BS EN 4800-005:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Forging stock |
| UNI EN 4800-008 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS |
| I.S. EN 4800-004:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE |
| UNI EN 4800-007 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK |
| UNI EN 4800-001 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP |
| NF EN 4800-008 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS |
| NF EN 4800-007 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK |
| BS EN 4800-008:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production castings |
| UNI EN 4800-003 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE |
| BS EN 4800-001:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Plate, sheet and strip |
| BS EN 4800-004:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Wire |
| BS EN 4800-002:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Bar and section |
| BS EN 4800-003:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Tube |
| NF EN 4800-004 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE |
| PREN 4800-008 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 8: PRE-PRODUCTION AND PRODUCTION CASTINGS |
| PREN 4800-002 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 2: BAR AND SECTION |
| NF EN 4800-001 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP |
| I.S. EN 4800-008:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS |
| EN 4800-003:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 003: Tube |
| EN 4800-002:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 002: Bar and section |
| EN 4800-001:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 001: Plate, sheet and strip |
| EN 4800-004:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 004: Wire |
| EN 4800-006:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 006: Pre-production and production forgings |
| EN 4800-008:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 008: Pre-production and production castings |
| EN 4800-007:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 007: Remelting stock |
| EN 4800-005:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 005: Forging stock |
| I.S. EN 4800-006:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| I.S. EN 4800-003:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE |
| BS EN 4800-007:2010 | Aerospace series. Titanium and titanium alloys Remelting stock |
| I.S. EN 4800-007:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK |
| PREN 4800-001 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 1: PLATE, SHEET AND STRIP |
| PREN 4800-007 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 7: REMELTING STOCK |
| PREN 4800-004 : 200P2 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 4: WIRE |
| UNI EN 4800-002 : 2011 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| I.S. EN 4800-001:2010 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP |
| ISO Guide 35:2017 | Reference materials Guidance for characterization and assessment of homogeneity and stability |
| ISO Guide 30:2015 | Reference materials Selected terms and definitions |
| PREN 2003-10 : 200P1 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TEST METHODS - PART 10: SAMPLING FOR DETERMINATION OF HYDROGEN CONTENT |
| PREN 4259 : 200P1 | AEROSPACE SERIES - METALLIC MATERIALS - DEFINITION OF GENERAL TERMS |
| EN 4258:1998 | Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use |
| ISO Guide 31:2015 | Reference materials — Contents of certificates, labels and accompanying documentation |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.