• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 60068-3-6:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers
Superseded date

01-03-2018

Published date

04-01-2002

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 Measuring of performances
  4.1 Test area environment
  4.2 Temperature measurement system
  4.3 Humidity measurement system
  4.4 Installation of sensors
5 Determination of humidity performance
  5.1 Temperature
6 Standard humidity sequence
7 Evaluation criteria
8 Information to be given in the performance test report
Annex ZA (normative) Normative references to international
         publications with their corresponding European
         publications

Provides a uniform and reproducible method of confirming that temperature and humidity test chambers without load conform to the requirements, specified in climatic test procedures contained in EN 60068-2 and is destined for users when conducting regular chamber performance monitoring.

Committee
CLC/SR 104
DevelopmentNote
To be read in conjunction with EN 60068-3-5 and EN 60068-3-7. (05/2002) Redesignated as EN IEC 60068-3-6. (04/2018)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

BS EN 60068-3-7:2002 Environmental testing. Guidance Measurements in temperature chambers for tests A and B (with load)
CEI EN 62093 : 2005 BALANCE-OF-SYSTEM COMPONENTS FOR PHOTOVOLTAIC SYSTEMS - DESIGN QUALIFICATION NATURAL ENVIRONMENTS
CEI EN 60068-3-7 : 2002 ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TEST A AND B (WITH LOAD)
BS EN 60068-3-11:2007 Environmental testing Supporting documentation and guidance - Calculation of uncertainty of conditions in climatic test chambers
I.S. EN 60068-3-11:2007 ENVIRONMENTAL TESTING - PART 3-11: SUPPORTING DOCUMENTATION AND GUIDANCE - CALCULATION OF UNCERTAINTY OF CONDITIONS IN CLIMATIC TEST CHAMBERS
UNE-EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
I.S. EN 60068-3-5:2002 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
I.S. EN 60068-3-7:2002 ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE - MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TESTS A AND B (WITH LOAD)
CEI EN 60068-2-78 : 2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE
CEI EN 60068-3-5 : 2002 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
BS EN 60068-2-30:2005 Environmental testing Tests. Test Db and guidance: Damp heat, cyclic (12 h + 12 h cycle)
EN 60068-3-7:2002 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
BS EN 60068-2-78:2013 Environmental testing Tests. Test Cab: Damp heat, steady state
CEI EN 60068-2-30 : 2006 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
BS EN 62093:2005 Balance-of-system components for photovoltaic systems. Design qualification natural environments
I.S. EN 60068-2-30:2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
I.S. EN 62093:2005 BALANCE-OF-SYSTEM COMPONENTS FOR PHOTOVOLTAIC SYSTEMS - DESIGN QUALIFICATION NATURAL ENVIRONMENTS
I.S. EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012 (EQV))
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
EN 60068-3-5:2002 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
EN 62093:2005 Balance-of-system components for photovoltaic systems - Design qualification natural environments
EN 60068-3-11:2007 Environmental testing - Part 3-11: Supporting documentation and guidance - Calculation of uncertainty of conditions in climatic test chambers

ISO 10012-2:1997 Quality assurance for measuring equipment Part 2: Guidelines for control of measurement processes
EN 30012-1 : 1993 QUALITY ASSURANCE REQUIREMENTS FOR MEASURING EQUIPMENT - METROLOGICAL CONFIRMATION SYSTEM FOR MEASURING EQUIPMENT
EN 60068-3-5:2002 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
EN 60068-3-7:2002 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
ISO 4677-1:1985 Atmospheres for conditioning and testing Determination of relative humidity Part 1: Aspirated psychrometer method
EN 60751:2008 INDUSTRIAL PLATINUM RESISTANCE THERMOMETERS AND PLATINUM TEMPERATURE SENSORS
IEC 60068-3-5:2001 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
EN 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
IEC 60751:2008 Industrial platinum resistance thermometers and platinum temperature sensors
EN 60068-3-4:2002 Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests
IEC 60068-3-4:2001 Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests
IEC 60068-3-7:2001 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
ISO 10012-1:1992 Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.