We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • EN 60079-17:2014

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Explosive atmospheres - Part 17: Electrical installations inspection and maintenance

    Available format(s): 

    Language(s): 

    Published date:  14-03-2014

    Publisher:  European Committee for Standards - Electrical

    Add to Watchlist
    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements
    5 Additional inspection schedule requirements
    6 Inspection tables
    Annex A (informative) - Typical inspection procedure for
            periodic inspections
    Annex B (normative) - Knowledge, skills and competencies of
            responsible persons, technical persons with executive
            function and operatives
    Annex C (informative) - Fitness-for-purpose assessment
    Annex D (informative) - Example of motor checks
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their corresponding
             European publications

    Abstract - (Show below) - (Hide below)

    IEC 60079-17:2013 applies to users and covers factors directly related to the inspection and maintenance of electrical installations within hazardous areas only, where the hazard may be caused by flammable gases, vapours, mists, dusts, fibres or flyings. It does not include: - other fundamental installation and inspection requirements for electrical installations; - the verification of electrical equipment; - the repair and reclamation of explosion protected equipment (see IEC 60079-19). This standard supplements the requirements of IEC 60364-6. In the case of dusts, fibres or flyings the level of housekeeping may influence the inspection and maintenance requirements. This standard is intended to be applied where there can be a risk due to the presence of explosive gas or dust mixtures with air or combustible dust layers under normal atmospheric conditions. It does not apply to: - underground mining areas, - dusts of explosives that do not require atmospheric oxygen for combustion, - pyrophoric substances. This fifth edition cancels and replaces the fourth edition published in 2007 and constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: - Equipment specific inspection tables for luminaires, heating systems and motors have been added into Annex A to supplement the general protection concept tables; - Document has been updated to complement the changes made to IEC 60079-14 for initial inspection. Keywords: inspection and maintenance of electrical installations within hazardous area, flammable gases, vapours, mists, dusts, fibres or flyings

    General Product Information - (Show below) - (Hide below)

    Committee CLC/TC 31
    Development Note Supersedes EN 61241-17. (10/2008)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    09/30182356 DC : 0 BS EN 12581:2005/A1 - COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    PREN 50050-1 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
    13/30277457 DC : 0 BS EN 1776 - GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
    PREN 1127-1 : DRAFT 2017 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
    UNE-EN 50050-2:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 2: Hand-held spraying equipment for ignitable coating powder
    11/30248849 DC : 0 BS EN 50050-3:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
    BS EN 15001-2 : 2008 GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    I.S. HD 60364-6:2007 LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 6: VERIFICATION
    UNE-EN 50050-3:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock
    17/30365866 DC : 0 BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
    18/30369304 DC : DRAFT APR 2018 BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    DIN EN 1473:2016-10 Installation and equipment for liquefied natural gas - Design of onshore installations
    BS EN 1755:2015 Industrial Trucks. Safety requirements and verification. Supplementary requirements for operation in potentially explosive atmospheres
    BS EN 50174-2 : 2009 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
    EN 50176:2009 Stationary electrostatic application equipment for ignitable liquid coating material - Safety requirements
    EN 50177:2009/A1:2012 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
    EN 50050-3 : 2013 Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock
    EN 62086-2 : 2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL RESISTANCE TRACE HEATING - PART 2: APPLICATION GUIDE FOR DESIGN, INSTALLATION AND MAINTENANCE
    11/30248842 DC : 0 BS EN 50050-1:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
    BS EN 60079-29-2:2015 EXPLOSIVE ATMOSPHERES - PART 29-2: GAS DETECTORS - SELECTION, INSTALLATION, USE AND MAINTENANCE OF DETECTORS FOR FLAMMABLE GASES AND OXYGEN
    BS EN 62086-2 : 2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL RESISTANCE TRACE HEATING - PART 2: APPLICATION GUIDE FOR DESIGN, INSTALLATION AND MAINTENANCE
    08/30180312 DC : DRAFT MAR 2008 BS EN 50223 - STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
    10/30230365 DC : 0 BS EN 50050-2 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    BS EN 50223:2015 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
    CEI EN 50176 : 2010 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    EN 50174-2 : 2009 AMD 2 2014 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
    S.R. HD 60364-6:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 6: VERIFICATION
    I.S. EN 50174-2:2009 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
    I.S. EN 50176:2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    CEI EN 50174-3 : 2014 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    I.S. EN 50177:2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
    I.S. EN 62086-2:2005 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL RESISTANCE TRACE HEATING - PART 2: APPLICATION GUIDE FOR DESIGN, INSTALLATION AND MAINTENANCE
    DIN EN 12581:2011-02 Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements (includes Amendment A1:2010)
    DIN EN 12981:2010-06 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
    BS EN 12981 : 2005 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
    BS EN 1473:2016 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    DIN EN 1473:1997-11 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    DIN EN 1755:2016-02 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
    DIN EN 1776:2016-05 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
    I.S. EN 12981:2005 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
    I.S. EN 1755:2015 INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - SUPPLEMENTARY REQUIREMENTS FOR OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    I.S. EN 1473:2016 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
    I.S. EN 1776:2015 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
    I.S. EN 12581:2006 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    CEI EN 50050-2 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    I.S. EN 15001-2:2008 GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    PREN 50223 : DRAFT 2013 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
    13/30257895 DC : 0 BS EN 1755 - SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST
    BS EN 50050-2 : 2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    PREN 1473 : DRAFT 2018 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    12/30260552 DC : 0 BS EN 50174-3:201X - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    EN 1473:2016 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    CEI EN 50050-1 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
    BS EN 50050-3 : 2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
    I.S. EN 60079-29-2:2015 EXPLOSIVE ATMOSPHERES - PART 29-2: GAS DETECTORS - SELECTION, INSTALLATION, USE AND MAINTENANCE OF DETECTORS FOR FLAMMABLE GASES AND OXYGEN
    UNI EN 15001-2 : 2009 GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    I.S. EN 50174-3:2013 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    PREN 50174-3 : DRAFT 2012 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    EEMUA 186 : 2016 A PRACTITIONER'S HANDBOOK FOR POTENTIALLY EXPLOSIVE ATMOSPHERES
    UNE-EN 60079-14:2016 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
    UNE-EN 1755:2016 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
    BS EN 60079-14:2014 (published 2016-04) Explosive atmospheres Electrical installations design, selection and erection
    UNI EN 12581 : 2010 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    UNI EN 12981 : 2009 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
    UNE-EN 50223:2016 Stationary electrostatic application equipment for ignitable flock material - Safety requirements
    BS EN 50176:2009 Stationary electrostatic application equipment for ignitable liquid coating material. Safety requirements
    I.S. EN 50050-3:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
    13/30284894 DC : 0 BS EN 50223 - STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
    PREN 15001-2 : DRAFT 2017 GAS SUPPLY SYSTEMS - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    PREN 50050-3 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
    PREN 50050-2 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    I.S. EN 50050-2:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    11/30248845 DC : 0 BS EN 50050-2:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    PREN 1755 : DRAFT 2013 SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST
    04/30116801 DC : 0 EN 15001-2 - GAS SUPPLY SYSTEMS - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0.5 BAR FOR INDUSTRIAL, COMMERCIAL AND NON-DOMESTIC INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    BS EN 50177 : 2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
    EN 50174-3:2013/A1:2017 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    CEI EN 60079-29-2 : 2016 EXPLOSIVE ATMOSPHERES - PART 29-2: GAS DETECTORS - SELECTION, INSTALLATION, USE AND MAINTENANCE OF DETECTORS FOR FLAMMABLE GASES AND OXYGEN
    UNE-EN 50050-1:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials
    UNE-EN 1776:2017 Gas infrastructure - Gas measuring systems - Functional requirements
    17/30361391 DC : 0 BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
    BS EN 1776:2015 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
    EI MODEL CODE SAFE PRACTICE PT1 : 2010 THE SELECTION, INSTALLATION, INSPECTION, AND MAINTENANCE OF ELECTRICAL AND NON ELECTRICAL APPARATUS IN HAZARDOUS AREAS
    EN 1755:2015 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
    EN 15001-2 : 2008 GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE
    EN 1776:2015 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
    EN 12581:2005+A1:2010 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    UNE-EN 50177:2010 Stationary electrostatic application equipment for ignitable coating powders - Safety requirements
    BS EN 50050-1 : 2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
    CEI EN 50050-3 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
    I.S. EN 50050-1:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
    14/30297213 DC : 0 BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
    I.S. EN 60079-14:2014 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
    UNE-EN 60079-29-2:2016 Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen
    BS EN 50174-3 : 2013 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    BS EN 60079-0 : 2012 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    I.S. EN 50223:2015 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
    BS EN 12581 : 2005 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    EN 12981:2005+A1:2009 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
    HD 60364-6:2016/AC:2017-11 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 6: VERIFICATION (IEC 60364-6:2016/COR1:2017)
    EN 60079-29-2 : 2015 EXPLOSIVE ATMOSPHERES - PART 29-2: GAS DETECTORS - SELECTION, INSTALLATION, USE AND MAINTENANCE OF DETECTORS FOR FLAMMABLE GASES AND OXYGEN (IEC 60079-29-2:2015)
    DIN EN 15001-2:2010-04 Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance
    EN 50050-2 : 2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
    EN 50050-1 : 2013 Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials
    EN 50223:2015 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    EN 61241-4 : 2006 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION 'PD'
    EN 60079-1:2014 EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D' (IEC 60079-1:2014)
    EN 60079-10-1:2015 EXPLOSIVE ATMOSPHERES - PART 10-1: CLASSIFICATION OF AREAS - EXPLOSIVE GAS ATMOSPHERES (IEC 60079-10-1:2015 + COR1:2015)
    IEC 60079-19:2010+AMD1:2015 CSV Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    EN 60079-15:2010 EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
    EN 60079-19:2011/A1:2015 EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION (IEC 60079-19:2010)
    ISO 31000:2009 Risk management Principles and guidelines
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    IEC 60079-18:2014 RLV Explosive atmospheres - Part 18: Equipment protection by encapsulation “m”
    EN 60079-10-2 : 2015 EXPLOSIVE ATMOSPHERES - PART 10-2: CLASSIFICATION OF AREAS - EXPLOSIVE DUST ATMOSPHERES (IEC 60079-10-2:2015)
    IEC 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
    IEC 60079-5:2015 RLV Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
    EN 60079-31:2014 EXPLOSIVE ATMOSPHERES - PART 31: EQUIPMENT DUST IGNITION PROTECTION BY ENCLOSURE 'T' (IEC 60079-31:2013)
    EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY "I" (IEC 60079-11:2011)
    IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    IEC 60364-6:2016 Low voltage electrical installations - Part 6: Verification
    IEC 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
    IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
    IEC 60079-14:2013 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
    IEC 61241-4:2001 Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection "pD"
    EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
    IEC 60079-31:2013 Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
    IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    IEC 60079-26:2014 RLV Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
    EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective