Surge arresters - Part 9: Metal-oxide surge arresters without gaps for HVDC converter stations

Published date

12-09-2014

Publisher

European Committee for Standards - Electrical

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Typical HVDC converter station schemes,
   arrester types, locations and operating voltage
5 Identification and classification
6 Service conditions
7 Requirements
8 General testing procedure
9 Type tests (design tests)
10 Routine tests and acceptance test
11 Test requirements on different types of arresters
Annex A (normative) - Test to verify thermal equivalency
        between complete arrester and arrester section
Annex B (normative) - Determination of the start
        temperature in the thermal recovery test
Annex C (normative) - Mechanical considerations
Annex D (informative) - Different circuit configurations
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 60099-9:2014 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit overvoltages in HVDC converter stations of two terminal, multiterminal and back-to-back type up to and including an operating voltage of 1 100 kV. The standard applies in general to porcelain-housed and polymer-housed type arresters but also to gas-insulated metal enclosed arresters (GIS-arresters) solely used as d.c. bus and d.c. line/cable arresters. Arresters for voltage source converters are not covered. Arresters applied on the a.c. systems at the converter station and subjected to power-frequency voltage of 50 or 60 Hz principally without harmonics are tested as per IEC 60099-4. The arresters on a.c.-filters are tested according to this standard. Keywords: testing of gapless metal-oxide surge arrestors for HVDC converter stations

Committee	CLC/SR 37
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current

Standards	Relationship
DIN EN 60099-9 : 2015	Identical
VDE 0675-9 : 2015	Identical
NBN EN 60099-9 : 2014	Identical
PN EN 60099-9 : 2015	Identical
CEI EN 60099-9 : 2015	Identical
I.S. EN 60099-9:2014	Identical
NEN EN IEC 60099-9 : 2014	Identical
IEC 60099-9:2014	Identical
NF EN 60099-9 : 2015	Identical
SN EN 60099-9:2014	Identical
BS EN 60099-9:2014	Identical
UNE-EN 60099-9:2014	Identical

IEC 60060-2:2010	High-voltage test techniques - Part 2: Measuring systems
ISO 4892-1:2016	Plastics Methods of exposure to laboratory light sources Part 1: General guidance
IEC 60143-2:2012	Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks
IEC 60270:2000+AMD1:2015 CSV	High-voltage test techniques - Partial discharge measurements
IEC 60143-1:2015	Series capacitors for power systems - Part 1: General
IEC 62271-200:2011	High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
EN ISO 4892-1:2016	Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN 62271-1:2017	High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
EN ISO 4892-3:2016	Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
IEC 60099-4:2014	Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems
CISPR 16-1-1:2015	Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
IEC 62217:2012	Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria
IEC TS 60815-2:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems
EN 62271-203:2012	High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
EN 60060-1:2010	High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60068-2-11:1981	Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN 60099-4:2014	Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems
EN 60270:2001/A1:2016	HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015)
EN 60507:2014	Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
IEC TS 60071-5:2002	Insulation co-ordination - Part 5: Procedures for high-voltage direct current (HVDC) converter stations
EN 60060-2:2011	High-voltage test techniques - Part 2: Measuring systems
EN 60143-2:2013	Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks
ISO 4892-3:2016	Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
EN 60068-2-17:1994	Environmental testing - Part 2: Tests - Test Q: Sealing
IEC 60068-2-17:1994	Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
IEC 62271-203:2011	High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
IEC 60721-3-2:1997	Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation
EN 60071-1:2006/A1:2010	INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
IEC 62271-1:2017	High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
CISPR TR 18-2:2017	Radio interference characteristics of overhead power lines and high-voltage equipment - Part 2: Methods of measurement and procedure for determining limits
IEC 60633:1998+AMD1:2009+AMD2:2015 CSV	Terminology for high-voltage direct current (HVDC) transmission
IEC 60071-2:1996	Insulation co-ordination - Part 2: Application guide
ISO 4892-2:2013	Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 60071-2:1997	Insulation co-ordination - Part 2: Application guide
EN 60068-2-11:1999	Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 60721-3-2:1997	Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation
IEC 60060-1:2010	High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60507:2013	Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
IEC 60071-1:2006+AMD1:2010 CSV	Insulation co-ordination - Part 1: Definitions, principles and rules
IEC 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC TS 60815-1:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
EN ISO 4892-2:2013	Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60143-1:2015/AC:2017-05	Series capacitors for power systems - Part 1: General
EN 60633:1999/A2:2015	TERMINOLOGY FOR HIGH-VOLTAGE DIRECT CURRENT (HVDC) TRANSMISSION (IEC 60633:1998/A2:2015)
EN 62217:2013	Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria
EN 62271-200:2012/AC:2015	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 200: AC METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV (IEC 62271-200:2011)
IEC TS 60815-3:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems
EN 55016-1-1:2010/A2:2014	SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS (CISPR 16-1-1:2010/A2:2014)