• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 60455-3-8:2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 8: Resins for cable accessories
Superseded date

19-08-2021

Published date

05-07-2013

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Type testing
6 Test methods
7 Information on supply, packaging, marking and labelling
Annex ZA (normative) - Normative references to international
         Publications with their corresponding European
         publications
Bibliography

IEC 60455-3-8:2013 gives the requirements for resins for power cable accessories which conform to this specification and meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not on this specification alone. Key words: requirements for resins for power cable accessories

Committee
CLC/SR 15
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

BS EN 50393:2015 Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV
I.S. EN 50655-1:2017 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERIZATION - PART 1: FINGERPRINTING FOR RESINOUS COMPOUNDS
UNE-EN 50393:2015 Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV
EN 50655-1:2017 Electric cables - Accessories - Material characterization - Part 1: Fingerprinting for resinous compounds
PREN 50655-1 : DRAFT 2015 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERIZATION - PART 1: FINGERPRINTING FOR RESINOUS COMPOUNDS
BS EN 50655-1:2017 Electric cables. Accessories. Material characterization Fingerprinting for resinous compounds
15/30325650 DC : 0 BS EN 50655-1 - ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERIZATION - PART 1: FINGERPRINTING FOR RESINOUS COMPOUNDS
I.S. EN 60455-2:2015 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST
BS EN 60455-2:2015 Resin based reactive compounds used for electrical insulation Methods of test
EN 50393:2015 Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV
I.S. EN 50393:2015 TEST METHODS AND REQUIREMENTS FOR ACCESSORIES FOR USE ON DISTRIBUTION CABLES OF RATED VOLTAGE 0,6/1,0 (1,2) KV
EN 60455-2:2015 Resin based reactive compounds used for electrical insulation - Part 2: Methods of test

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
HD 629.2 S2:2006/A1:2008 TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 2: CABLES WITH IMPREGNATED PAPER INSULATION
ISO 7056:1981 Plastics laboratory ware Beakers
ISO 3521:1997 Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage
IEC 60212:2010 Standard conditions for use prior to and during the testing of solid electrical insulating materials
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
IEC 60455-2:2015 Resin based reactive compounds used for electrical insulation - Part 2: Methods of test
IEC 60455-1:1998 Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements
ISO 4895:2014 Plastics Liquid epoxy resins Determination of tendency to crystallize
EN ISO 4895:2014 Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:2014)
HD 429 : 200S1 METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS
ISO 2555:1989 Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 61234-2:1997 Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
EN 60243-1:2013 ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013)
EN 60455-2:2015 Resin based reactive compounds used for electrical insulation - Part 2: Methods of test
EN ISO 868:2003 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003)
EN 60212:2011 Standard conditions for use prior to and during the testing of solid electrical insulating materials
EN 50393:2015 Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
HD 629.1 S2:2006/A1:2008 TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 1: CABLES WITH EXTRUDED INSULATION
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.