• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 60512-23-3:2001

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories
Superseded date

31-01-2022

Published date

21-02-2001

Clause
1 Scope and object
2 Normative references
3 Test method
   3.1 Test requirements
   3.2 Test screen diameter
   3.3 Applicable frequency range
4 Test equipment
5 Preparation of the test sample under test
   5.1 Circular connectors
   5.2 Rectangular connectors
   5.3 Connectors for printed boards
   5.4 Impedance matching of primary and secondary
        circuit
   5.5 Preparation of the secondary circuit
   5.6 Adaptation of the primary circuit
   5.7 Calibration of test set-up
6 Measurement of shielding effectiveness
   6.1 Measurement
   6.2 Method of calculating attenuation
7 Requirements
8 Details to be specified
Annex ZA (normative) Normative references to
         international publications with their
         corresponding European publications

Defines a standard test method for measuring the shielding effectiveness of a connector, or a connector fitted with an accessory and terminated with a cable. The complete assembly has a continuous 360° shielding capability throughout its length.

DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

09/30208429 DC : 0 BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
I.S. EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
UNE-EN 50467:2012 Railway applications - Rolling stock - Electrical connectors, requirements and test methods
I.S. EN 60512-23-7:2005 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 23-7: SCREENING AND FILTERING TESTS - TEST 23G: EFFECTIVE TRANSFER IMPEDANCE OF CONNECTORS
I.S. EN 50467:2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
CEI EN 60512-23-7 : 2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 23-7: SCREENING AND FILTERING TESTS - TEST 23G: EFFECTIVE TRANSFER IMPEDANCE OF CONNECTORS
EN 61076-4-110:2002 Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function
CEI EN 61076-4-110 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
CEI EN 50467 : 2013 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
PREN 50467 : DRAFT 2009 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
CEI EN 50173-1 : 2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
BS EN 61076-4-110:2002 Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function
DD CLC/TS 50467:2008 Railway applications. Rolling stock. Electrical connectors, requirements and test methods
BS EN 50173-1:2011 Information technology. Generic cabling systems General requirements
EN 50173-1:2011 Information technology - Generic cabling systems - Part 1: General requirements
S.R. CLC/TS 50467:2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
I.S. EN 61076-4-110:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
BS EN 2591-212:2005 Aerospace series. Elements of electrical and optical connection. Test methods Surface transfer impedance
CLC/TS 50467 : 2008 COR 2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
EN 2591-212:2005 Aerospace series - Elements of electrical and optical connection - Test methods - Part 212: Surface transfer impedance
BS EN 50467:2011 Railway applications. Rolling stock. Electrical connectors, requirements and test methods
08/30171133 DC : DRAFT FEB 2008 BS ISO 20860-2 - ROAD VEHICLES - 50 IMPEDANCE RADIO FREQUENCY CONNECTION SYSTEM INTERFACE - PART 2: TEST PROCEDURES
EN 60512-23-7:2005 Connectors for electronic equipment - Tests and measurements - Part 23-7: Screening and filtering tests - Test 23g: Effective transfer impedance of connectors
EN 50467 : 2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS

IEC 60096-4-1:1990 Radio-frequency cables. Part 4: Specification for superscreened cables - Section One: General requirements and test methods

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.