EN 60793-1-31:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
01-02-2022
24-09-2010
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Apparatus
4 Sample preparation
5 Procedure
6 Calculations
7 Results
8 Specification information
Annex A (informative) - Typical dynamic testing apparatus
Annex B (informative) - Guideline on gripping the fibre
Annex C (informative) - Guideline on stress rate
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Bibliography
IEC 60793-1-31:2010(E) provides values of the tensile strength of optical fibre samples and establishes uniform requirements for the mechanical characteristic - tensile strength. The method tests individual lengths of uncabled and unbundled glass optical fibre. Sections of fibre are broken with controlled increasing stress or strain that is uniform over the entire fibre length and cross section. The stress or strain is increased at a nominally constant rate until breakage occurs. The main change with respect to the previous edition is the addition of comprehensive details, such as examples of fibre clamping as given in Annexes A, B and C.
| Committee |
CLC/TC 86A
|
| DevelopmentNote |
Partially supersedes EN 188000 (07/2002) Supersedes UNE EN 188000. (01/2012)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| OVE/ONORM EN 60793-1-31 : 2011 | Identical |
| IEC 60793-1-31:2010 | Identical |
| NBN EN 60793 1-31 : 2010 | Identical |
| NEN EN IEC 60793-1-31 : 2010 | Identical |
| I.S. EN 60793-1-31:2010 | Identical |
| PN EN 60793-1-31 : 2011 | Identical |
| DIN EN 60793-1-31 : 2011 | Identical |
| VDE 0888-231 : 2011 | Identical |
| UNE-EN 60793-1-31:2010 | Identical |
| BS EN 60793-1-31:2010 | Identical |
| CEI EN 60793-1-31 : 2012 | Identical |
| NF EN 60793-1-31 : 2011 | Identical |
| BS EN 60793-2-20:2016 | Optical fibres Product specifications. Sectional specification for category A2 multimode fibres |
| EN 60793-2-30:2015 | Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres |
| EN 60793-1-1:2017 | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| EN 60793-2-20:2016 | Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimode fibres |
| EN 60793-2-60:2008 | Optical fibres - Part 2-60: Product specifications - Sectional specification for category C single-mode intraconnection fibres |
| UNE-EN 60793-1-1:2017 | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| BS EN 61757-1-1:2017 | Fibre optic sensors Strain measurement. Strain sensors based on fibre Bragg gratings |
| BS EN 60793-2-60:2008 | Optical fibres Product specifications. Sectional specification for category C single-mode intraconnection fibres |
| BS EN 60793-1-1:2017 | Optical fibres Measurement methods and test procedures. General and guidance |
| BS EN 60793-2-30:2015 | Optical fibres Product specifications. Sectional specification for category A3 multimode fibres |
| BS EN 60793-2-50:2016 | Optical fibres Product specifications. Sectional specification for class B single-mode fibres |
| UNE-EN 60793-1-50:2015 | Optical fibres - Part 1-50: Measurement methods - Damp heat (steady state) tests |
| CEI EN 60793-2-60 : 2009 | OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES |
| I.S. EN 60793-2-50:2016 | OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| CEI EN 60793-2-30 : 2016 | OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| EN 61757-1-1:2017 | Fibre optic sensors – Part 1-1: Strain measurement – Strain sensors based on fibre Bragg gratings |
| BS EN 60794-3-11:2010 | Optical fibre cables Outdoor cables. Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables |
| CEI EN 60793-1-1 : 2010 | OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| BS EN 60793-1-50:2015 | Optical fibres Measurement methods. Damp heat (steady state) tests |
| EN 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| BS EN 60793-2-10:2017 | Optical fibres Product specifications. Sectional specification for category A1 multimode fibres |
| EN 3745-502:2005 | Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 502: Tensile stength for short length of optical fibres |
| I.S. EN 60793-2-10:2017 | OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRE |
| I.S. EN 60793-1-50:2015 | OPTICAL FIBRES - PART 1-50: MEASUREMENT METHODS - DAMP HEAT (STEADY STATE) TESTS |
| I.S. EN 60793-2-60:2008 | OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES |
| I.S. EN 60793-2-30:2015 | OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| I.S. EN 60793-1-1:2017 | OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| BS EN 3745-502:2005 | Aerospace series. Fibres and cables, optical, aircraft use. Test methods Tensile strength for short length of optical fibres |
| EN 60794-3-11:2010 | Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables |
| EN 60793-2-50:2016 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| EN 60793-1-50:2015 | Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests |
| EN 60793-1-21:2002 | Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry |
| EN 60793-1-20:2014/AC:2016-03 | OPTICAL FIBRES - PART 1-20: MEASUREMENT METHODS AND TEST PROCEDURES - FIBRE GEOMETRY (IEC 60793-1-20:2014/COR1:2016) |
| IEC 61649:2008 | Weibull analysis |
| IEC TR 62048:2014 | Optical fibres - Reliability - Power law theory |
| IEC 60793-1-21:2001 | Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry |
| IEC 60793-1-20:2014 | Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.