• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 61290-1-3:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
Superseded date

22-04-2021

Published date

12-06-2015

FOREWORD
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Apparatus
5 Test sample
6 Procedure
7 Calculation
8 Test results
Annex A (informative) - Optimization of optical
        bandpass filter spectral width
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 61290-1-3:2015 applies to all commercially available optical amplifiers (OA) and optically amplified subsystems. It applies to OA using optically pumped fibres (OFA based on either rare-earth doped fibres or on the Raman effect), semiconductors (SOA), and waveguides (POWA). The object of this part of IEC 61290-1 is to establish uniform requirements for accurate and reliable measurements, by means of the optical power meter test method, of the following OA parameters, as defined in IEC 61291-1:- nominal output signal power;- gain;- polarization-dependent gain;- maximum output signal power;- maximum total output power. All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values may be acceptable but should be verified. This part of IEC 61290-1 applies to single-channel amplifiers. For multichannel amplifiers, the IEC 61290-10 series applies. This third edition cancels and replaces the second edition published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:- Detail description of most parameters has been described in IEC 61290-1 and removed from this part;- Description of maximum output signal power and maximum total output power are added.Keywords: optical amplifiers (OA), single-channel amplifiers, optical power meter test method

Committee
CLC/SR 86C
DevelopmentNote
To be read in conjunction with EN 61290-1. (06/2015)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

BS EN 61291-1:2012 Optical amplifiers Generic specification
I.S. EN 61291-1:2012 OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION (IEC 61291-1:2012 (EQV))
I.S. EN IEC 61291-1:2018 OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION
EN 61290-1:2015 Optical amplifiers - Test methods - Part 1: Power and gain parameters
CEI EN 61291-1 : 2013 OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION
CEI EN 60728-6 : 2012 CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 6: OPTICAL EQUIPMENT
BS EN 62149-9:2014 Fibre optic active components and devices. Performance standards Seeded reflective semiconductor optical amplifier transceivers
BS EN 61290-4-2:2011 Optical amplifiers. Test methods Gain transient parameters. Broadband source method
BS EN 61290-1:2015 Optical amplifiers. Test methods Power and gain parameters
EN IEC 61291-1:2018 Optical amplifiers - Part 1: Generic specification
BS EN 60728-6:2011 Cable networks for television signals, sound signals and interactive services Optical equipment
I.S. EN 61290-1:2015 OPTICAL AMPLIFIERS - TEST METHODS - PART 1: POWER AND GAINPARAMETERS
EN 61290-4-2:2011 Optical amplifiers - Test methods - Part 4-2: Gain transient parameters - Broadband source method
EN 61291-1:2012 Optical amplifiers - Part 1: Generic specification
EN 60728-6:2011 Cable networks for television signals, sound signals and interactive services - Part 6: Optical equipment
EN 62149-9:2014 Fibre optic active components and devices - Performance standards - Part 9: Seeded reflective semiconductor optical amplifier transceivers

EN 61291-1:2012 Optical amplifiers - Part 1: Generic specification
IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS)
IEC 60793-1-1 : 2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
EN 61290-1-1:2015 Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
EN 60793-2-50:2016 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
IEC 61290-1-1:2015 Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
EN 61290-1:2015 Optical amplifiers - Test methods - Part 1: Power and gain parameters
EN 60793-1-40:2003 Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
EN 60874-1:2012 Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification
IEC 60793-1-40:2001 Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
IEC TR 61931:1998 Fibre optic - Terminology
IEC 60874-1:2011 Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification
IEC 61290-1:2014 Optical amplifiers - Test methods - Part 1: Power and gain parameters
IEC 61291-1:2012 Optical amplifiers - Part 1: Generic specification
IEC 60793-2-50:2015 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 60825-2:2004/A2:2010 SAFETY OF LASER PRODUCTS - PART 2: SAFETY OF OPTICAL FIBRE COMMUNICATION SYSTEMS (OFCS)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.