EN 61290-3-1:2003
Current
The latest, up-to-date edition.
27-11-2003
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Abbreviations
4 Apparatus
5 Test sample
6 Procedure
6.1 Calibration
6.1.1 Calibration of optical bandwidth
6.1.2 Calibration of nulling stage insertion loss
6.1.3 Calibration of OSA power correction factor
6.2 Measurement
6.2.1 Single channel DI technique
6.2.2 PN technique
7 Calculation
8 Test results
Annex A (normative) Limitation of direct interpolation
techniques due to source spontaneous emission
Bibliography
Applies to commercially available optical amplifiers (OAs) such as optical fibre amplifiers (OFAs), semiconductor optical amplifiers (SOAs) and planar wageguide apmlifiers (PWOAs) as classified in EN 61292-3.The object is to establish uniform requirements for accurate and reliable measurements, by means of optical spectrum analyzer (OSA) test method, of the following OA parameters, as defined in EN 61291-1: a) signal-spontaneous noise figure; b) forward amplified spontaneous emission (ASE) power level. The methods outlined in this part of EN 61290 apply to single-channel stimulus only.
| Committee |
CLC/SR 86C
|
| DevelopmentNote |
To be read in conjunction with EN 61291-1: 1998. (01/2004)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Standards | Relationship |
| NF EN 61290-3-1 : 2004 | Identical |
| CEI EN 61290-3-1 : 2005 | Identical |
| NEN EN IEC 61290-3-1 : 2003 | Identical |
| DIN EN 61290-3-1:2004-05 | Identical |
| IEC 61290-3-1:2003 | Identical |
| NBN EN 61290 3-1 : 2005 | Identical |
| I.S. EN 61290-3-1:2003 | Identical |
| UNE-EN 61290-3-1:2003 | Identical |
| PN EN 61290-3-1 : 2004 | Identical |
| BS EN 61290-3-1:2003 | Identical |
| I.S. EN 61290-3:2008 | OPTICAL AMPLIFIERS - TEST METHODS - PART 3: NOISE FIGURE PARAMETERS |
| I.S. EN IEC 61291-1:2018 | OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION |
| EN 61280-2-9:2009 | Fibre optic communication subsystem test procedures - Part 2-9: Digital systems - Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems |
| EN 61290-10-2:2008 | Optical amplifiers - Test methods - Part 10-2: Multichannel parameters - Pulse method using a gated optical spectrum analyzer |
| EN 62129:2006/corrigendum:2006 | CALIBRATION OF OPTICAL SPECTRUM ANALYZERS |
| EN 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers |
| CEI EN 61291-1 : 2013 | OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION |
| BS EN 61290-4-1:2016 | Optical amplifiers. Test methods Gain transient parameters. Two-wavelength method |
| BS EN 61290-10-2:2008 | Optical amplifiers. Test methods Multichannel parameters. Pulse method using a gated optical spectrum analyzer |
| BS EN 61280-2-9:2009 | Fibre optic communication subsystem test procedures Digital systems. Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems |
| I.S. EN 61291-1:2012 | OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION (IEC 61291-1:2012 (EQV)) |
| BS EN 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments Optical spectrum analyzers |
| BS EN 62129:2006 | Calibration of optical spectrum analyzers |
| EN IEC 61291-1:2018 | Optical amplifiers - Part 1: Generic specification |
| I.S. EN 61280-2-9:2009 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 2-9: DIGITAL SYSTEMS - OPTICAL SIGNAL-TO-NOISE RATIO MEASUREMENT FOR DENSE WAVELENGTH-DIVISION MULTIPLEXED SYSTEMS |
| BS EN 61291-1:2012 | Optical amplifiers Generic specification |
| BS EN 61290-3:2008 | Optical amplifiers. Test methods Noise figure parameters |
| CEI EN 61290-3 : 2010 | OPTICAL AMPLIFIERS - TEST METHODS - PART 3: NOISE FIGURE PARAMETERS |
| EN 61290-4-1:2016 | Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method |
| EN 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| EN 61290-3:2008 | Optical amplifiers - Test methods - Part 3: Noise figure parameters |
| EN 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| IEC 60793-1-1 : 2017 | OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| IEC TR 61292-3:2003 | Optical amplifiers - Part 3: Classification, characteristics and applications |
| EN 61290-1-1:2015 | Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61290-1-1:2015 | Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method |
| IEC TR 61931:1998 | Fibre optic - Terminology |
| IEC 60874-1:2011 | Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification |
| IEC 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| IEC 61290-3:2008 | Optical amplifiers - Test methods - Part 3: Noise figure parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.