• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 61439-1:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Low-voltage switchgear and controlgear assemblies - Part 1: General rules
Superseded date

10-07-2021

Published date

28-10-2011

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Interface characteristics
6 Information
7 Service conditions
8 Constructional requirements
9 Performance requirements
10 Design verification
11 Routine verification
Annex A (normative) - Minimum and maximum cross-section
        of copper conductors suitable for connection
        to terminals for external conductors
Annex B (normative) - Method of calculating the
        cross-sectional area of protective
        conductors with regard to thermal stresses
        due to currents of short duration
Annex C (informative) - User information template
Annex D (informative) - Design verification
Annex E (informative) - Rated diversity factor
Annex F (normative) - Measurement of clearances and creepage
        distances
Annex G (normative) - Correlation between the nominal voltage
        of the supply system and the rated impulse withstand
        voltage of the equipment
Annex H (informative) - Operating current and power loss of
        copper conductors
Annex I (Void)
Annex J (normative) - Electromagnetic compatibility (EMC)
Annex K (normative) - Protection by electrical separation
Annex L (informative) - Clearances and creepage distances
        for North American region
Annex M (informative) - North American temperature rise
        limits
Annex N (normative) - Operating current and power loss
        of bare copper bars
Annex O (informative) - Guidance on temperature rise
        verification
Annex P (normative) - Verification of the short-circuit
        withstand strength of busbar structures by comparison
        with a tested reference design by calculation
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications
Annex ZZ (informative) - Coverage of Essential Requirements
        of EC Directive 2004/108/EC

IEC 61439-1:2011 lays down the definitions and states the service conditions, construction requirements, technical characteristics and verification requirements for low-voltage switchgear and controlgear assemblies. This standard cannot be used alone to specify an ASSEMBLY or used for a purpose of determining conformity. ASSEMBLIES shall comply with the relevant part of the IEC 61439 series; Parts 2 onwards. This standard applies to low-voltage switchgear and controlgear assemblies (ASSEMBLIES) only when required by the relevant ASSEMBLY standard as follows: - ASSEMBLIES for which the rated voltage does not exceed 1 000 V in case of a.c. or 1 500 V in case of d.c.; - stationary or movable ASSEMBLIES with or without enclosure; - ASSEMBLIES intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; - ASSEMBLIES designed for use under special service conditions, for example in ships and in rail vehicles provided that the other relevant specific requirements are complied with; - ASSEMBLIES designed for electrical equipment of machines provided that the other relevant specific requirements are complied with. This second edition cancels and replaces the first edition published in 2009. It constitutes a technical revision. This second edition includes the following significant technical changes with respect to the last edition of IEC 61439-1: - revision of service conditions in Clause 7; - numerous changes regarding verification methods in Clause 10; - modification of routine verification in respect of clearances and creepage distances (see 11.3); - adaption of the tables in Annex C and Annex D to the revised requirements and verification methods; - revision of the EMC requirements in Annex J; - shifting of tables from Annex H to new Annex N; - new Annex O with guidance on temperature rise verification; - new Annex P with a verification method for short-circuit withstand strength (integration of the content of IEC/TR 61117); - update of normative references; - general editorial review.

Committee
CLC/SR 121B
DevelopmentNote
Supersedes EN 60439-1. (01/2010)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

DIN EN 16840:2015-04 (Draft) INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREE-PHASE CURRENT 400 V, 50 HZ, AT LEAST 250 A
DIN EN 16564 E : 2015 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS
BS EN 61851-23:2014 Electric vehicle conductive charging system DC electric vehicle charging station
DIN EN 16564:2015-04 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
BS EN 61439-2:2011 Low-voltage switchgear and controlgear assemblies Power switchgear and controlgear assemblies
S.R. HD 60364-5-557:2013 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-557: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - AUXILIARY CIRCUITS
BS EN 62040-1 : 2008 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS
I.S. EN 15571:2014 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES
I.S. EN 61439-2:2011 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 2: POWER SWITCHGEAR AND CONTROLGEAR ASSEMBLIES (IEC 61439-2:2011)
BS EN 50153 : 2014 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
I.S. EN 62271-212:2017 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 212: COMPACT EQUIPMENT ASSEMBLY FOR DISTRIBUTION SUBSTATION (CEADS)
UNE-EN 62271-212:2017 High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Substation (CEADS)
BS EN 12111:2014 Tunnelling machines. Road headers and continuous miners. Safety requirements
UNI EN 81-22 : 2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 22: ELECTRIC LIFTS WITH INCLINED PATH
BS EN 62477-1 : 2012 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012)
EN 61439-3 : 2012 COR 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 3: DISTRIBUTION BOARDS INTENDED TO BE OPERATED BY ORDINARY PERSONS (DBO) (IEC 61439-3:2012)
EN 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
EN 16191:2014 Tunnelling machinery - Safety requirements
EN 62271-212:2017 High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Substation (CEADS)
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
EN 62271-202:2014/AC:2014 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION (IEC 62271-202:2014)
HD 60364-5-557:2013/A11:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-557: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - AUXILIARY CIRCUITS
HD 60364-5-54:2011/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
UNE-EN 61439-5:2015 Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
BS EN 62282-5-1:2012 Fuel cell technologies Portable fuel cell power systems. Safety
DIN EN 15571:2015-03 Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines
UNI EN 16191 : 2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
UNE-EN 61439-6:2013 Low-voltage switchgear and controlgear assemblies - Part 6: Busbar trunking systems (busways)
BS EN 16191:2014 Tunnelling machinery. Safety requirements
15/30317827 DC : 0 BS EN 16840 - INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREEPHASE CURRENT 400 V, 50 HZ AND AT LEAST 250 A
BS EN 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies. General requirements
I.S. EN 16932-1:2018 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS
I.S. EN 16840:2017 INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREE-PHASE CURRENT 400 V, 50 HZ, AT LEAST 250 A
CEI EN 62208 : 2012 EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - GENERAL REQUIREMENTS
I.S. EN 15163:2017 MACHINES AND INSTALLATIONS FOR THE EXPLOITATION AND PROCESSING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR DIAMOND WIRE SAWS
I.S. EN 62271-202:2014 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION
I.S. EN 16564:2014 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS
BS EN 61439-3:2012 Low-voltage switchgear and controlgear assemblies Distribution boards intended to be operated by ordinary persons (DBO)
PREN 17206 : DRAFT 2018 ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
I.S. EN 61439-5:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 5: ASSEMBLIES FOR POWER DISTRIBUTION IN PUBLIC NETWORKS
I.S. EN 61851-23:2014 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION
EN 81-22:2014 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
I.S. EN 62040-1:2008 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS (IEC 62040-1:2008 (EQV))
EN 16564:2014 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
I.S. EN 12111:2014 TUNNELLING MACHINES - ROAD HEADERS AND CONTINUOUS MINERS - SAFETY REQUIREMENTS
EN 15571:2014 Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines
DIN EN 50153 : 2018 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
VDE 0115-2 : 2018 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
BS EN 15571:2014 Machines and plants for mining and tooling of natural stone. Safety. Requirements for surface finishing machines
BS EN 16840:2017 Inland navigation vessels. Electrical shore connection, three-phase current 400 V, 50 Hz, at least 250 A
BS EN 15572:2015 Machines and plants for mining and tooling of natural stone. Safety. Requirements for edge finishing machines
CEI EN 61439-2 : 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 2: POWER SWITCHGEAR AND CONTROLGEAR ASSEMBLIES
DIN EN 16191:2014-09 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
UNE-EN 16564:2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
UNE-EN 62208:2012 Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
I.S. EN 15572:2015 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES
EN 16932-1:2018 Drain and sewer systems outside buildings - Pumping systems - Part 1: General requirements
I.S. EN 50153:2014 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
UNE-EN 62271-202:2015 High-voltage switchgear and controlgear - Part 202: High-voltage/low-voltage prefabricated substation
UNE-EN 60079-14:2016 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
UNE-EN 60947-4-1:2011 Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
BS EN 81-22:2014 Safety rules for the construction and installation of lifts. Lifts for the transport of persons and goods Electric lifts with inclined path
UNE-EN 81-22:2014 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
UNI EN 12111 : 2014 TUNNELLING MACHINES - ROAD HEADERS AND CONTINUOUS MINERS - SAFETY REQUIREMENTS
BS EN 16564:2014 Machines and plants for mining and tooling of natural stone. Safety. Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
DIN EN 16191 E : 2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
DIN EN 15572:2015-12 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES
10/30233949 DC : 0 BS EN 12111 - TUNNELLING MACHINES - ROAD HEADERS, CONTINUOUS MINERS AND IMPACT RIPPERS - SAFETY REQUIREMENTS
BS EN 61439-5:2015 Low-voltage switchgear and controlgear assemblies Assemblies for power distribution in public networks
UNE-EN 15163:2018 Machines and installations for the exploitation and processing of natural stone - Safety - Requirements for diamond wire saws
15/30325882 DC : 0 BS EN 16932-1 - DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS
DIN EN 15571 E : 2015 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES
BS EN 15163:2017 Machines and installations for the exploitation and processing of natural stone. Safety. Requirements for diamond wire saws
UNE-EN 61439-4:2013 Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)
I.S. EN 61439-6:2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 6: BUSBAR TRUNKING SYSTEMS (BUSWAYS) (IEC 61439-6:2012 (EQV))
I.S. EN 16191:2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
S.R. HD 60364-5-54:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
I.S. EN 61439-3:2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 3: DISTRIBUTION BOARDS INTENDED TO BE OPERATED BY ORDINARY PERSONS (DBO) (IEC 61439-3:2012 (EQV))
EN 15163:2017 Machines and installations for the exploitation and processing of natural stone - Safety - Requirements for diamond wire saws
I.S. EN 62208:2011 EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - GENERAL REQUIREMENTS (IEC 62208:2011)
S.R. CLC/TR 50480:2011 DETERMINATION OF CROSS-SECTIONAL AREA OF CONDUCTORS AND SELECTION OF PROTECTIVE DEVICES
EN 50153 : 2014 AMD 1 2017 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
BS EN 62271-212:2017 High-voltage switchgear and controlgear Compact Equipment Assembly for Distribution Substation (CEADS)
UNE-HD 62640:2016 Residual current devices with or without overcurrent protection for socket-outlets for household and similar uses
PD CLC/TR 50480:2011 Determination of cross-sectional area of conductors and selection of protective devices
UNE-EN 61851-23:2015 Electric vehicle conductive charging system - Part 23: DC electric vehicle charging station
EN 16840:2017 Inland navigation vessels - Electrical shore connection, three-phase current 400 V, 50 Hz, at least 250 A
EN 15572:2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for edge finishing machines
I.S. EN 61439-4:2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 4: PARTICULAR REQUIREMENTS FOR ASSEMBLIES FOR CONSTRUCTION SITES (ACS) (IEC 61439-4:2012 (EQV))
DIN EN 15572 E : 2015 MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES
BS EN 60947-4-1 : 2010 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
18/30366946 DC : 0 BS EN 17206 - ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
BS EN 61439-6:2012 Low-voltage switchgear and controlgear assemblies Busbar trunking systems (busways)
BS EN 61439-4:2013 Low-voltage switchgear and controlgear assemblies Particular requirements for assemblies for construction sites (ACS)
UNE-EN 15571:2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines
CEI EN 61439-6 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 6: BUSBAR TRUNKING SYSTEMS (BUSWAYS)
EN 61439-2 : 2011 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 2: POWER SWITCHGEAR AND CONTROLGEAR ASSEMBLIES (IEC 61439-2:2011)
UNE-EN 16840:2017 Inland navigation vessels - Electrical shore connection, three-phase current 400 V, 50 Hz, at least 250 A
I.S. EN 81-22:2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 22: ELECTRIC LIFTS WITH INCLINED PATH
I.S. HD 60364-5-54:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
I.S. EN 60947-4-1:2010 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009 (EQV))
EN 62477-1:2012/A1:2017 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012/A1:2016)
EN 62040-1:2008/A1:2013 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS (IEC 62040-1:2008/A1:2013)
DIN EN 81-22:2014-12 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
BS EN 62271-202:2014 High-voltage switchgear and controlgear High-voltage/low-voltage prefabricated substation
EN 61851-23:2014/AC:2016-06 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION (IEC 61851-23:2014/COR1:2016)
CLC/TR 50480:2011 Determination of cross-sectional area of conductors and selection of protective devices
EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012)
EN 61439-6 : 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 6: BUSBAR TRUNKING SYSTEMS (BUSWAYS) (IEC 61439-6:2012)
EN 61439-5:2015/AC:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 5: ASSEMBLIES FOR POWER DISTRIBUTION IN PUBLIC NETWORKS (IEC 61439-5:2014)
EN 12111:2014 Tunnelling machines - Road headers and continuous miners - Safety requirements
EN 61439-4:2013 Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)
UNE-HD 60364-5-557:2014 Low-voltage electrical installations - Part 5-557: Selection and erection of electrical equipment - Auxiliary circuits
UNE-HD 60364-5-54:2015 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors

EN 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
IEC 61000-4-8 : 2.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-8: TESTING AND MEASUREMENT TECHNIQUES - POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60364-5-54:2011 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors
IEC TR 61912-1:2007 Low-voltage switchgear and controlgear - Overcurrent protective devices - Part 1: Application of short-circuit ratings
IEC 60227-4:1992+AMD1:1997 CSV Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 4: Sheathed cables for fixed wiring
IEC 61000-6-4:2006+AMD1:2010 CSV ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN 81346-2 : 2009 INDUSTRIAL SYSTEMS, INSTALLATIONS AND EQUIPMENT AND INDUSTRIAL PRODUCTS - STRUCTURING PRINCIPLES AND REFERENCE DESIGNATIONS - PART 2: CLASSIFICATION OF OBJECTS AND CODES FOR CLASSES
EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments
IEC 60228:2004 Conductors of insulated cables
IEC 61000-3-11 : 2.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-11: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS - EQUIPMENT WITH RATED CURRENT <= 75 A AND SUBJECT TO CONDITIONAL CONNECTION
HD 21-3 : S3 AMD 2 2008 POLYVINYL CHLORIDE INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V - NON-SHEATHED CABLES FOR FIXED WIRING
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
EN 61000-6-3:2007/A1:2011/AC:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010)
IEC 60050-195:1998 International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock
EN 60085:2008 Electrical insulation - Thermal evaluation and designation
EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
IEC 61000-6-2:2016 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments
IEC 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
IEC 60050-601:1985 International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General
EN 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
EN 61000-3-11:2000 Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current
IEC 60050-471:2007 International Electrotechnical Vocabulary (IEV) - Part 471: Insulators
IEC TS 61201:2007 Use of conventional touch voltage limits - Application guide
IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 61000-4-11:2004+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
EN 61000-3-3:2013 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION (IEC 61000-3-3:2013)
IEC 60502-1:2004+AMD1:2009 CSV Power cables with extruded insulation and their accessories for rated voltages from 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) up to 30 kV(<em>U</em><sub>m</sub> = 36 kV) - Part 1: Cables for rated voltages of 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) and 3 kV (<em>U</em><sub>m</sub> = 3,6 kV)
IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
IEC TR 61912-2:2009 Low-voltage switchgear and controlgear - Over-current protective devices - Part 2: Selectivity under over-current conditions
IEC 60227-3:1993+AMD1:1997 CSV Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 3: Non-sheathed cables for fixed wiring
IEC 81346-1:2009 Industrial systems, installations and equipment and industrial products - Structuring principles and reference designations - Part 1: Basic rules
IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
HD 60364-4-41:2017/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
HD 60364-5-54:2011/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
IEC 61000-6-1 : 3.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
IEC 61000-4-8:2009 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
IEC 61000-3-12:2011 Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and ≤ 75 A per phase
IEC 61000-4-4:2012 RLV Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
2004/108/EC : 2004 DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 DECEMBER 2004 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY AND REPEALING DIRECTIVE 89/336/EC
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
EN 61000-4-2:2009 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
EN 60228:2005 COR 2005 CONDUCTORS OF INSULATED CABLES
IEC 81346-2:2009 Industrial systems, installations and equipment and industrial products - Structuring principles and reference designations - Part 2: Classification of objects and codes for classes
IEC 61082-1:2014 RLV Preparation of documents used in electrotechnology - Part 1: Rules
EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
HD 22-4 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING CROSS-LINKED INSULATION - PART 4: CORDS AND FLEXIBLE CABLES
EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 61000-4-6 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
IEC 61000-4-6:2013 Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
CISPR 22:2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
EN 61000-4-3 : 2006 AMD 2 2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
HD 60364-4-444:2010/AC:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-444: PROTECTION FOR SAFETY - PROTECTION AGAINST VOLTAGE DISTURBANCES AND ELECTROMAGNETIC DISTURBANCES
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
IEC 61000-6-3:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
EN 60447:2004 Basic and safety principles for man-machine interface, marking and identification - Actuating principles
IEC 60865-1:2011 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
EN ISO 4628-3:2016 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016)
IEC 60447:2004 Basic and safety principles for man-machine interface, marking and identification - Actuating principles
EN 55022:2010/AC:2011 INFORMATION TECHNOLOGY EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT (CISPR 22:2008)
EN 61000-6-2:2005/corrigendum:2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 61000-4-8:2010 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
EN 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60364-4-44:2007+AMD1:2015 CSV Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
IEC 60245-4:2011 Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 4: Cords and flexible cables
EN 61000-6-4:2007/A1:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
EN 60865-1:2012 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
IEC 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
IEC 61000-3-3:2013 RLV Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection
EN 61082-1:2015 Preparation of documents used in electrotechnology - Part 1: Rules
EN 61000-3-2:2014 Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
IEC 61000-6-1:2016 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments
CLC/TR 60890:2002 A method of temperature-rise assessment by extrapolation for partially type-tested assemblies (PTTA) of low-voltage switchgear and controlgear
IEC 61000-6-4:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
EN 61000-3-12:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011)
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 81346-1:2009 Industrial systems, installations and equipment and industrial products - Structuring principles and reference designations - Part 1: Basic rules
IEC 60050-826:2004 International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations
IEC 61000-3-3 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION
EN 61000-4-4:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012)
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 61000-4-6:2014/AC:2015 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
EN 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
ISO 2409:2013 Paints and varnishes Cross-cut test
EN 60695-11-5:2017 Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
IEC 60695-11-5:2016 Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
ISO 178:2010 Plastics Determination of flexural properties
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
IEC 60445:2017 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN 61000-4-13:2002/A2:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015)
IEC 60092-302:1997 Electrical installations in ships - Part 302: Low-voltage switchgear and controlgear assemblies
IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests
EN 60038 : 2011 CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED)
DIN 43671:1975-12 COPPER BUS BARS; DESIGN FOR CONTINUOUS CURRENT
IEC TR 60890:2014 A method of temperature-rise verification of low-voltage switchgear and controlgear assemblies by calculation
IEC 60364-5-52:2009 Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems
EN 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.