AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) - Performance requirements for low frequency squarewave operation

Published date

22-05-2015

Publisher

European Committee for Standards - Electrical

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General notes on tests
5 Marking
6 General statement
7 Starting conditions
8 Operating conditions
9 Displacement factor
10 Supply current
11 Endurance
Annex A (normative) - Tests
Annex B (normative) - Reference ballasts
Annex C (normative) - Conditions for reference lamps
Annex D (normative) - Control interface for controllable
        controlgear
Annex E (normative) - Spectral analysis of power ripple:
        calculation procedure for amplitude spectrum
        ratio and guidance
Annex F (normative) - Open circuit voltage method of
        measurement for pulse ignition
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 62811:2015 specifies performance requirements for electronic controlgear for use on a.c. and/or d.c. supplies up to 1 000 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, as specified in IEC 61167, which have information for low frequency square wave operation, where the frequency range of the low frequency is from 70 Hz to 400 Hz.

Committee	CLC/TC 34
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current

Standards	Relationship
UNE-EN 62811:2015	Identical
BS EN 62811:2015	Identical
I.S. EN 62811:2015	Identical
NBN EN 62811 : 2015	Identical
PN EN 62811 : 2015	Identical
NEN EN IEC 62811 : 2015	Identical
NF EN 62811 : 2015	Identical
DIN EN 62811:2016-03	Identical
CEI EN 62811 : 2016	Identical
SN EN 62811:2015	Identical
CEI EN 62811 :2018	Identical
IEC 62811:2015	Identical

IEC 61000-4-30 : 3.0EN+(REDLINE+VERSION)	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-30: TESTING AND MEASUREMENT TECHNIQUES - POWER QUALITY MEASUREMENT METHODS
EN 61000-4-30:2015/AC:2017-01	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-30: TESTING AND MEASUREMENT TECHNIQUES - POWER QUALITY MEASUREMENT METHODS (IEC 61000-4-30:2015/COR1:2016)
IEC 61547:2009	Equipment for general lighting purposes - EMC immunity requirements
IEC 61347-1:2015 RLV	Lamp controlgear - Part 1: General and safety requirements
EN 61000-4-14:1999/A2:2009	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-14: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE FLUCTUATION IMMUNITY TEST FOR EQUIPMENT WITH INPUT CURRENT NOT EXCEEDING 16 A PER PHASE
IEC 61167:2015	Metal halide lamps - Performance specification
IEC 60410:1973	Sampling plans and procedures for inspection by attributes
EN 61347-1:2015	Lamp controlgear - Part 1: General and safety requirements
IEC 61347-2-12:2005+AMD1:2010 CSV	Lamp controlgear - Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
EN 61000-3-2:2014	Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
IEC 61000-4-14:1999+AMD1:2001+AMD2:2009 CSV	Electromagnetic compatibility (EMC) - Part 4-14: Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase
EN 61547:2009	Equipment for general lighting purposes - EMC immunity requirements
IEC 61000-3-2 : 4.0	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)