EN 818-7:2002+A1:2008
Current
The latest, up-to-date edition.
02-04-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Hazards
5 Safety requirements
6 Verification of safety requirements
7 Marking
8 Manufacturer's certificate
9 Information for use and assembly of the hoist chain
into the hoist
Annex A (normative) - Calculation of dimensions, working
load limits and mechanical properties
Annex B (normative) - Selection criteria for fine tolerance
chain for power driven hoists, Types T, DAT and DT
Annex C (informative) - Designation system for hoist chain -
grade T
Annex D (informative) - Approximate mass of Grade T hoist
chain
Annex E (informative) - Chain use
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
This European Standard specifies the requirements related to safety for hoist chain, Grade T (type T quenched and tempered and types DAT and DT case hardened), for use in serial chain hoists manual and power driven.Type DAT and type DT hoist chains possess surface hardnesses greater than core hardness and are used for power driven chain hoists to offer greater resistance to wear.Type DT hoist chain differs from DAT hoist chain in having higher surface hardness and/or greater case depth to optimise wear resistance.The standard is applicable to electrically welded round steel short link hoist chains conforming to EN 818-1.The range of nominal size of hoist chains covered by this European Standard is from 4 mm to 22 mm.The hazards covered by this European Standard are identified in clause 4.
| Committee |
CEN/TC 168
|
| DevelopmentNote |
2002 Edition Re-Issued in April 2008 & incorporates AMD 1 2008. (04/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| NBN EN 818-7 : 2002 + A1 2008 | Identical |
| BS EN 818-7 : 2002 | Identical |
| PN EN 818-7 : 2004 + A1 2008 | Identical |
| NF EN 818-7 : 2002 + A1 2008 | Identical |
| I.S. EN 818-7:2002 | Identical |
| DIN EN 818-7:2008-07 | Identical |
| NEN EN 818-7 : 2002 + A1 2008 | Identical |
| NS EN 818-7 : 2002 + A1 2008 | Identical |
| UNE-EN 818-7:2002 | Identical |
| SN EN 818-7 : 2002 + A1 2008 | Identical |
| UNI EN 818-7 : 2008 | Identical |
| UNE-EN 818-7:2002+A1:2008 | Identical |
| BS EN 818-7:2002+A1:2008 | Identical |
| 18/30366946 DC : 0 | BS EN 17206 - ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS) |
| 11/30235014 DC : 0 | BS EN 13135 - CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| EN 13157:2004+A1:2009 | Cranes - Safety - Hand powered cranes |
| EN 13135-2:2004+A1:2010 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
| 04/19993045 DC : 0 | EN 14492-1 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| PREN 17206 : DRAFT 2018 | ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS) |
| 16/30341165 DC : 0 | BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| I.S. EN 14492-2:2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| S.R. CWA 15902-1:2009 | LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - PART 1: GENERAL REQUIREMENTS (EXCLUDING ALUMINIUM AND STEEL TRUSSES AND TOWERS) |
| DIN EN 13157:2010-07 | Cranes - Safety - Hand powered cranes (includes Amendment A1:2009) |
| DIN EN 14502-2:2009-05 | CRANES - EQUIPMENT FOR THE LIFTING OF PERSONS - PART 2: ELEVATING CONTROL STATIONS |
| UNE-EN 13135-2:2005 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
| I.S. EN 14492-1:2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| DIN EN 14492-1:2010-06 | Cranes - Power driven winches and hoists - Part 1: Power driven winches (includes Amendment A1:2009) |
| I.S. EN 13157:2004 | CRANES - SAFETY - HAND POWERED CRANES |
| I.S. EN 14502-2:2005 | CRANES - EQUIPMENT FOR THE LIFTING OF PERSONS - PART 2: ELEVATING CONTROL STATIONS |
| EN 13135:2013+A1:2018 | Cranes - Safety - Design - Requirements for equipment |
| 09/30181658 DC : DRAFT JAN 2009 | BS EN 13157 AMD1 - CRANES - SAFETY - HAND POWERED LIFTING EQUIPMENT |
| STANAG 2830 : 2009 | MATERIAL HANDLING AIDS |
| I.S. EN 13135:2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| UNE-EN 13135:2013 | Cranes - Safety - Design - Requirements for equipment |
| BS EN 13135-2 : 2004 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
| UNI EN 13135-2 : 2010 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
| UNI EN 13157 : 2009 | CRANES - SAFETY - HAND POWERED CRANES |
| UNI EN 14502-2 : 2008 | CRANES - EQUIPMENT FOR THE LIFTING OF PERSONS - PART 2: ELEVATING CONTROL STATIONS |
| UNI EN 14492-2 : 2009 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| UNI EN 14492-1 : 2009 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| BS EN 13135 : 2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| DIN EN 13135:2013-05 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| BS EN 13157 : 2004 | CRANES - SAFETY - HAND POWERED CRANES |
| BS EN 14492-1 : 2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| BS EN 14502-2 : 2005 | CRANES - EQUIPMENT FOR THE LIFTING OF PERSONS - PART 2: ELEVATING CONTROL STATIONS |
| EN 14492-1:2006+A1:2009/AC:2010 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| EN 14502-2:2005+A1:2008 | Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations |
| EN 14492-2:2006+A1:2009/AC:2010 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| 04/30122476 DC : 0 | EN 14492-1 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| DIN EN 14492-2:2016-08 (Draft) | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| DIN EN 13135-2:2011-07 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
| DIN EN 14502-2 E : 2009 | CRANES - EQUIPMENT FOR THE LIFTING OF PERSONS - PART 2: ELEVATING CONTROL STATIONS |
| DIN EN 14492-1:2015-05 (Draft) | Cranes - Power driven winches & hoists - part 1 power driven winches; German and English version prEN 14492-1:2015 |
| BS EN 14492-2 : 2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| DIN EN 14492-2:2010-05 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO 7592:1983 | Calibrated round steel link lifting chains Guidelines to proper use and maintenance |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| EN 818-1:1996+A1:2008 | Short link chain for lifting purposes - Safety - Part 1: General conditions of acceptance |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| ISO 4301-1:2016 | Cranes — Classification — Part 1: General |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| ISO 4965:1979 | Axial load fatigue testing machines Dynamic force calibration Strain gauge technique |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.