• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 940:2009+A1:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Safety of woodworking machines - Combined woodworking machines
Superseded date

25-03-2022

Published date

29-02-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) - Stability test for displaceable machines
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 2006/42/EC
Bibliography

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable combined woodworking machines with two or more of only the following integrated units:-surface planing,-circular sawing (working simultaneously or not with vertical spindle moulding unit),-vertical spindle moulding,-boring [mortising] and-thickness planinghereinafter referred to as machines, designed to cut solid wood, chipboard, fibreboard, plywood, and also these materials where they are covered with plastic laminates or edging or veneer, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.NOTE 1For the definitions of stationary and displaceable machine see 3.2.12 and 3.2.13.NOTE 2The specific requirements on demountable power feed unit will be considered during next revision of this document.This document does not apply to:-combined machines which consist only of a surface planing unit and a thickness planing unit;NOTE 3Combined machines consisting of only of a surface planing unit and a thickness planing unit are dealt with in EN 861:2007+A2:2012.-combined machines with a band saw unit;-transportable motor-operated electric combined tools, or any adaptation permitting their use in a different mode, i.e. bench mounting;NOTE 4Transportable motor-operated electric combined tools are covered by the requirements of EN 61029-1:2009 and EN 61029-2-11:2009.-machines with mortising unit driven by a separate motor.This document is not applicable to combined woodworking machines which are manufactured before the date of its publication as EN.NOTE 5Machines covered by this European Standard are listed under 5 of Annex IV of Machinery Directive 2006/42/EC.

Committee
CEN/TC 142
DevelopmentNote
2009 Edition Re-Issued in February 2012 & incorporates AMD 1 2012. (03/2012)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

I.S. EN 861:2007 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
EN 1218-3:2001+A1:2009 Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
NF EN 1218-1 : 2000 + A1 2009 SAFETY OF WOOD WORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
UNI EN 1218-1 : 2009 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
08/30178378 DC : 0 BS EN 1218-3:2001/A1 - SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
DIN EN 1218-1:2010-02 Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table (includes Amendment A1:2009)
DIN EN 1218-3:2009-12 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN 1218-3:2002 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN 1218-1:2000 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
EN 1218-1:1999+A1:2009 Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
BS EN 861 : 2007 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
UNI EN 861 : 2012 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
UNI EN 1218-3 : 2009 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
DIN EN 861:2012-09 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
BS EN 1218-3 : 2001 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
EN 861:2007+A2:2012 Safety of woodworking machines - Surface planing and thicknessing machines
BS EN 1218-1 : 1999 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE

EN 1005-4:2005+A1:2008 Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery
ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
EN 61029-2-11:2012/A11:2013 SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-11: PARTICULAR REQUIREMENTS FOR COMBINED MITRE AND BENCH SAWS
EN 861:2007+A2:2012 Safety of woodworking machines - Surface planing and thicknessing machines
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
EN 1870-1:2007+A1:2009 Safety of woodworking machines - Circular sawing machines - Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
EN 61800-5-2:2017 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
EN 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
EN ISO 3743-2:2009 Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
ISO 3743-2:1994 Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
IEC 60947-4-1:2009+AMD1:2012 CSV Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
ISO 7960:1995 Airborne noise emitted by machine tools Operating conditions for woodworking machines
EN 1093-9:1998+A1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method
ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
EN 614-2:2000+A1:2008 Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks
EN 50370-2:2003 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity
IEC 61029-2-11:2001 Safety of transportable motor-operated electric tools - Part 2-11: Particular requirements for mitre-bench saws
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1005-1:2001+A1:2008 Safety of machinery - Human physical performance - Part 1: Terms and definitions
EN 1005-2:2003+A1:2008 Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
EN 12779:2015 Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN ISO 3745:2012/A1:2017 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012/AMD 1:2017)
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
IEC 61029-1:1990 Safety of transportable motor-operated electric tools - Part 1: General requirements
HD 22-4 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING CROSS-LINKED INSULATION - PART 4: CORDS AND FLEXIBLE CABLES
HD 22-1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS
HD 21.1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS
EN 61508-2:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems
ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN ISO 4414:2010 Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
IEC 60439-1:1999+AMD1:2004 CSV Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies
ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN 60439-1:1999/A1:2004 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN 847-1:2017 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN ISO 13849-2:2012 Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
EN ISO 3743-1:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 61029-1:2009/A11:2010 SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS
EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
EN 860:2007+A2:2012 Safety of woodworking machines - One side thickness planing machines
IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 859:2007+A2:2012 Safety of woodworking machines - Hand fed surface planing machines
ISO 3745:2012 Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
EN ISO 4413:2010 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
EN 50370-1 : 2005 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
IEC 61508-2:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508)
EN 1093-11:2001+A1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index
IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
ISO 3743-1:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
PREN 1870-18 : DRAFT 2011 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.