• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN IEC 61076-3-119:2018

Current
Current

The latest, up-to-date edition.

Connectors for electrical and electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for shielded and unshielded, free and fixed 10-way connectors with push-pull coupling for industrial environments for data transmission with frequencies up to 100 MHz
Published date

16-03-2018

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Technical information
5 Dimensional information
6 Characteristics
7 Test schedule
Annex ZA (normative) - Normative references to
         international publications with their corresponding
         European publications

IEC 61076-3-119:2017(E) establishes specifications and test requirements for 10-way shielded and unshielded rectangular, free and fixed connectors, with push-pull coupling, for data transmission with frequencies up to 100 MHz and for use in industrial environments.This document specifies free and fixed connectors with round contacts, suitable for screw or crimp terminations. Other terminations techniques, such as solder or printed board connections are upon agreement between manufacturer and user. The free and fixed connectors have a push-pull locking mechanism for IP65 and IP67 protection according to IEC 60529.Connectors according this document are without breaking capacity COC according to 3.9 of IEC 61984:2008, therefore they are not intended to be engaged or disengaged in normal use when live or under load, if not otherwise specified by the manufacturer.Key words: Connectors, Rectangular Connectors, 10 Way Connectors, Push-Pull Coupling

Committee
CLC/SR 48B
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current

IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
IEC 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
EN 60352-2:2006/A1:2013 SOLDERLESS CONNECTIONS - PART 2: CRIMPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
IEC 60512-11-4:2002 Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
IEC 60512-11-9:2002 Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
IEC 60512-11-10:2002 Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
EN 60512-11-9:2002 Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
IEC 61984:2008 Connectors - Safety requirements and tests
IEC 60512-3-1:2002 Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
EN ISO 1101:2017 Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
EN 60512-11-1:1999 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60512-13-5:2006 Connectors for electronic equipment - Tests and measurements - Part 13-5: Mechanical operation tests - Test 13e: Polarizing and keying method
EN 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60512-6-3:2002 Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
EN 60512-11-12 : 2002 Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
EN 60512-15-7:2008 Connectors for electronic equipment - Tests and measurements - Part 15-7: Connector tests (mechanical) - Test 15g: Robustness of protective cover attachment
EN 60512-15-6:2008 Connectors for electronic equipment - Tests and measurements - Part 15-6: Connector tests (mechanical) - Test 15f: Effectiveness of connector coupling devices
IEC 60512-15-1:2008 Connectors for electronic equipment - Tests and measurements - Part 15-1: Connector tests (mechanical) - Test 15a: Contact retention in insert
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
EN ISO 1302 : 2002 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION (ISO 1302:2002)
EN 60512-26-100:2008/A1:2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 26-100: MEASUREMENT SETUP, TEST AND REFERENCE ARRANGEMENTS AND MEASUREMENTS FOR CONNECTORS ACCORDING TO IEC 60603-7 - TESTS 26A TO 26G
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
ISO 11469:2016 Plastics — Generic identification and marking of plastics products
IEC 60512-13-2:2006 Connectors for electronic equipment - Tests and measurements - Part 13-2: Mechanical operation tests - Test 13b: Insertion and withdrawal forces
IEC 62430:2009 Environmentally conscious design for electrical and electronic products
IEC 60512-5-1:2002 Connectors for electronic equipment - Tests and measurements - Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise
EN ISO 11469:2016 Plastics - Generic identification and marking of plastics products (ISO 11469:2016)
EN 60512-11-3:2002 Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
EN 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
IEC 60512-16-5:2008 Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
EN 60512-5-1 : 2002 Connectors for electronic equipment - Tests and measurements - Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise
EN 60512-6-4:2002 Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
EN 60512-13-2 : 2006 COR 2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 13-2: MECHANICAL OPERATION TESTS - TEST 13B: INSERTION AND WITHDRAWAL FORCES
EN 60352-5:2012/AC:2014 SOLDERLESS CONNECTIONS - PART 5: PRESS-IN CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE (IEC 60352-5:2012)
EN 60512-15-1 : 2008 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 15-1: CONNECTOR TESTS (MECHANICAL) - TEST 15A: CONTACT RETENTION IN INSERT
ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
IEC 60512-26-100:2008+AMD1:2011 CSV Connectors for electronic equipment - Tests and measurements - Part 26-100: Measurement setup, test and reference arrangements and measurements for connectors according to IEC 60603-7 - Tests 26a to 26g
EN 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11- 7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
IEC 60512-11-3:2002 Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
EN 60512-1-2:2002 Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60512-1-1:2002 Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
IEC 60352-5:2012 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60512-16-5:2008 Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
IEC 60512-11-1:1995 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
IEC 60512-2-1:2002 Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method
IEC 60512-9-1:2010 Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
EN 62430:2009 Environmentally conscious design for electrical and electronic products
IEC 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
EN 60512-3-1:2002 Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
IEC 60512-11-12:2002 Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
EN 60512-11-10:2002 Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
IEC 60512-4-1:2003 Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
EN 62197-1 : 2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
IEC 60352-2:2006+AMD1:2013 CSV Solderless connections - Part 2: Crimped connections - Generalrequirements, test methods and practical guidance
EN 60512-13-5:2006/corrigendum Dec. 2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 13-5: MECHANICAL OPERATION TESTS - TEST 13E: POLARIZING AND KEYING METHOD
EN 60999-1:2000 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
IEC 62197-1:2006 Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification
EN 61984:2009 Connectors - Safety requirements and tests
IEC 60512-15-7:2008 Connectors for electronic equipment - Tests and measurements - Part 15-7: Connector tests (mechanical) - Test 15g: Robustness of protective cover attachment
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60512-4-1:2003 Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
EN 60512-1-1:2002 Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
EN 60512-6-3:2002 Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
IEC 60512-6-4:2002 Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
IEC 60512-15-6:2008 Connectors for electronic equipment - Tests and measurements - Part 15-6: Connector tests (mechanical) - Test 15f: Effectiveness of connector coupling devices
IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC 60512-1-2:2002 Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
EN 60512-9-1 : 2010 Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
EN 60512-11-4:2002 Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
EN 60512-2-1:2002 Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.