Name: EN ISO 11297-4:2018
Brand: CEN

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 4: Lining with cured-in-place pipes (ISO 11297-4:2018)

Published date

14-02-2018

Publisher

Comite Europeen de Normalisation

European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed
lining system at the 'I' stage
9 Installation practice
Bibliography

ISO 11297-4:2018, in conjunction with ISO 11297‑1 and ISO 11296‑4, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of hydraulically and pneumatically pressurized underground drainage and sewerage networks with service temperatures up to 50 °C.ISO 11297-4:2018 applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline.ISO 11297-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1).ISO 11297-4:2018 does not include requirements or test methods for resistance to abrasion, cyclic loading or impact, which are outside the scope of this document.

Committee	CEN/TC 155
DocumentType	Standard
PublisherName	Comite Europeen de Normalisation
Status	Current

Standards	Relationship
NEN EN ISO 11297-4 : 2018	Identical
NS EN ISO 11297-4 : 2018	Identical
SS-EN ISO 11297-4:2018	Identical
NF EN ISO 11297-4 : 2018	Identical
ISO 11297-4:2018	Identical
I.S. EN ISO 11297-4:2018	Identical
ÖNORM EN ISO 11297-4: 2018	Identical
SN EN ISO 11297-4:2018	Identical
UNI EN ISO 11297-4:2018	Identical
DIN EN ISO 11297-4:2018-09	Identical
UNE-EN ISO 11297-4:2018	Identical
BS EN ISO 11297-4:2018	Identical

ISO 8521:2009	Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
ISO 7432:2002	Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
ISO 10467:2004	Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ISO 10928:2016	Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
ISO 11295:2017	Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 8533:2003	Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
ISO 11296-4:2009	Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes
ISO 14125:1998	Fibre-reinforced plastic composites Determination of flexural properties
ISO 11297-1:2013	Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Part 1: General
ISO 10952:2014	Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
ISO 7509:2015	Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of time to failure under sustained internal pressure