• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 204:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009)
Superseded date

09-04-2019

Published date

15-06-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and designations
5 Principle
6 Apparatus
7 Test pieces
8 Test procedure
9 Determination of results
10 Test validity
11 Accuracy of the results
12 Test report
Annex A (informative) - Information concerning different
                        types of thermocouples
Annex B (informative) - Information concerning methods of
                        calibration of thermocouples
Annex C (normative) - Creep testing using test pieces with V
                      or blunt circumferential notches
Annex D (informative) - Method of estimating the uncertainty
                        of the measurement in accordance with
                        the Guide to the expression of
                        uncertainty in measurement (GUM)
Annex E (informative) - Representation of results and
                        graphical extrapolation
Bibliography

ISO 204:2009 specifies the method for the uninterrupted and interrupted creep tests and defines the properties of metallic materials which can be determined from these tests, in particular the creep elongation and the time of creep rupture, at a specified temperature.The stress rupture test is also covered, as is the testing of notched test pieces.

Committee
CEN/TC 459/SC 1
DevelopmentNote
Supersedes EN 10291. (08/2009)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

BS EN 12101-3:2015 Smoke and heat control systems Specification for powered smoke and heat control ventilators (Fans)
EN 12101-3:2015 Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans)
PREN 764-4 : DRAFT 2012 PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS
BS EN 13445-2 : 2014 UNFIRED PRESSURE VESSELS - PART 2: MATERIALS
DIN EN 12101-3:2015-12 SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
UNE-EN 12101-3:2016 Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans)
I.S. EN 12101-3:2015 SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
I.S. EN 764-4:2014 PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS
12/30259070 DC : 0 BS EN 764-4 - PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS
EN 13445-2:2014/A2:2018 UNFIRED PRESSURE VESSELS - PART 2: MATERIALS
UNE-EN 764-4:2015 Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials
I.S. EN 13445-2:2014 UNFIRED PRESSURE VESSELS - PART 2: MATERIALS
BS EN 764-4:2014 Pressure equipment Establishment of technical delivery conditions for metallic materials
EN 764-4:2014 Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials
UNE-EN 13445-2:2015 Unfired pressure vessels - Part 2: Materials
S.R. CWA 16200:2010 A GUIDE TO THE DEVELOPMENT AND USE OF STANDARDS COMPLIANT DATA FORMATS FOR ENGINEERING MATERIALS TEST DATA
DIN EN 764-4:2015-03 PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS

ISO/TS 4949:2016 Steel names based on letter symbols
ISO 783:1999 Metallic materials Tensile testing at elevated temperature
ISO/IEC Guide 25:1990 General requirements for the competence of calibration and testing laboratories
ISO 9513:2012 Metallic materials — Calibration of extensometer systems used in uniaxial testing
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
ISO 7500-2:2006 Metallic materials Verification of static uniaxial testing machines Part 2: Tension creep testing machines Verification of the applied force
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
EN 45001 : 1989 GENERAL CRITERIA FOR THE OPERATION OF TESTING LABORATORIES

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.