• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 21809-5:2017

Current
Current

The latest, up-to-date edition.

Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External concrete coatings (ISO 21809-5:2017)
Published date

02-08-2017

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 General requirements
6 Information supplied by the purchaser
7 Materials
8 Concrete mix
9 Coating application
10 Curing methods
11 Inspection and testing
12 Repair of concrete coated pipe
13 Markings
14 Handling and storage
15 Test reports and inspection documents
Annex A (normative) - Water absorption test
Annex B (normative) - Shear resistance test
Bibliography

ISO 21809-5:2017 specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.The external application of concrete is primarily used for the negative buoyancy of pipes used in buried or submerged pipeline systems and/or for the mechanical protection of the pipe and its pre-coating.ISO 21809-5:2017 is applicable to concrete thicknesses of 25 mm or greater.

Committee
CEN/TC 459/SC 10
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

EN 12390-3:2009/AC:2011 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
ISO 21809-2:2014 Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings
EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
ISO 16120-2:2017 Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for general purpose wire rod
ASTM C 171 : 2016 : REDLINE Standard Specification for Sheet Materials for Curing Concrete
EN 10244-2:2009 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings
EN 13263-1:2005+A1:2009 Silica fume for concrete - Part 1: Definitions, requirements and conformity criteria
EN 12390-7:2009 Testing hardened concrete - Part 7: Density of hardened concrete
ASTM C 331 : 2005 Standard Specification for Lightweight Aggregates for Concrete Masonry Units
ASTM C 1240 : 2015 : REDLINE Standard Specification for Silica Fume Used in Cementitious Mixtures
ASTM C 642 : 2013 : REDLINE Standard Test Method for Density, Absorption, and Voids in Hardened Concrete
ISO 3183:2012 Petroleum and natural gas industries Steel pipe for pipeline transportation systems
EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 1008:2002 Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
ASTM D 4643 : 2017 : REDLINE Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating
ASTM C 637 : 2014 : REDLINE Standard Specification for Aggregates for Radiation-Shielding Concrete
ASTM C 332 : 2017 : REDLINE Standard Specification for Lightweight Aggregates for Insulating Concrete
ASTM C 309 : 2011 : REDLINE Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete
ISO 1920-5:2004 Testing of concrete Part 5: Properties of hardened concrete other than strength
ASTM C 128 : 2015 : REDLINE Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
EN 12620:2002+A1:2008 Aggregates for concrete
ISO 14001:2015 Environmental management systems — Requirements with guidance for use
ISO 10474:2013 Steel and steel products — Inspection documents
EN 12390-2:2009 Testing hardened concrete - Part 2: Making and curing specimens for strength tests
ASTM C 330 : 2005 Standard Specification for Lightweight Aggregates for Structural Concrete
EN 10204:2004 Metallic products - Types of inspection documents
ISO 80000-1:2009 Quantities and units — Part 1: General
ASTM D 4959 : 2016 : REDLINE Standard Test Method for Determination of Water Content of Soil By Direct Heating
EN 450-1:2012 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
EN 206-1:2000/A2:2005 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
ASTM A 810 : 2001 : R2008 Standard Specification for Zinc-Coated (Galvanized) Steel Pipe Winding Mesh
EN 13055-1:2002/AC:2004 LIGHTWEIGHT AGGREGATES - PART 1: LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR AND GROUT
ASTM C 40 : 2004 Standard Test Method for Organic Impurities in Fine Aggregates for Concrete
EN 12504-1:2009 Testing concrete in structures - Part 1: Cored specimens - Taking, examining and testing in compression
ASTM C 1176 : 2005 Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table
ACI 308.1 : 2011 SPECIFICATION FOR CURING CONCRETE
ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
EN 934-2:2009+A1:2012 Admixtures for concrete, mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.