Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

EN ISO 2692:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Geometrical product specifications (GPS) - Geometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) (ISO 2692:2014)
Superseded date

30-06-2021

Published date

17-12-2014

Publisher

Comite Europeen de Normalisation

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Maximum material requirement, MMR and least
  material requirement, LMR
5 Reciprocity requirement, RPR
Annex A (informative) - Examples of tolerancing
        with [M],[L] and [R]
Annex B (informative) - Concept diagram
Annex C (informative) - Relation to the GPS matrix
        model
Bibliography

ISO 2692:2014 defines the maximum material requirement, the least material requirement and the reciprocity requirement. These requirements can only be applied to features of size.These requirements are used to control specific functions of workpieces where size and geometry are interdependent, e.g. to fulfil the functions "assembly of parts" (for maximum material requirement) or "minimum wall thickness" (for least material requirement). However, the maximum material requirement and least material requirement are also used to fulfil other functional design requirements.Considering this interdependence between size and geometry, the principle of independency defined in ISO 8015 does not apply when the maximum material requirement, least material requirement, or reciprocity requirement, are used.

Committee
CEN/TC 290
DevelopmentNote
Supersedes PREN ISO 2692. (01/2015)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
BS EN 60191-6:2009 Mechanical standardization of semiconductor devices General rules for the preparation of outline drawings of surface mounted semiconductor device packages
DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013)
EN 60191-6:2009 Mechanical standardization of semiconductor devices - Part 6: General rules for the preparation of outline drawings of surface mounted semiconductor device packages

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 7083:1983 TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
ISO 22432:2011 Geometrical product specifications (GPS) — Features utilized in specification and verification
ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us