• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 1090-2:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
Available format(s)

Hardcopy , PDF

Superseded date

11-06-2022

Language(s)

English

Published date

01-01-2008

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specifications and documentation
5 Constituent products
6 Preparation and assembly
7 Welding
8 Mechanical fastening
9 Erection
10 Surface treatment
11 Geometrical tolerances
12 Inspection, testing and correction
Annex A (normative) - Additional information, list of
        options and requirements related to the execution
        classes
Annex B (informative) - Guidance for the determination
        of execution classes
Annex C (informative) - Check-list for the content of a
        quality plan
Annex D (normative) - Geometrical tolerances
Annex E (informative) - Welded joints in hollow sections
Annex F (normative) - Corrosion protection
Annex G (normative) - Test to determine slip factor
Annex H (normative) - Calibration test for preloaded
        bolts under site conditions
Annex J (normative) - Use of compressible washer-type
        direct tension indicators
Annex K (informative) - Hexagon injection bolts
Annex L (informative) - Guide to flow diagram for
        development and use of a WPS
Annex M (normative) - Sequential method for fasteners
        inspection
Bibliography

Describes requirements independent of the type and shape of the steel structure (e.g. buildings, bridges, plated or latticed components) including structures subjected to fatigue or seismic actions.

DevelopmentNote
Supersedes I.S. ENV 1090-1, I.S. ENV 1090-2, I.S. ENV 1090-3, I.S. ENV 1090-4, I.S. ENV 1090-5 and I.S. ENV 1090-6. (09/2008) 2008 Edition Re-issued in August 2011 & incorporates AMD 1 2011. (08/2011)
DocumentType
Standard
Pages
212
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN 1090-2:2008+A1:2011 Identical

I.S. EN 1993-1-9 NATIONAL ANNEX:2005 IRISH NATIONAL ANNEX TO EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE

EN ISO 1479:2011 Hexagon head tapping screws (ISO 1479:2011)
ISO 10511:2012 Prevailing torque type hexagon thin nuts (with non-metallic insert)
ISO 9018:2015 Destructive tests on welds in metallic materials Tensile test on cruciform and lapped joints
ISO/TR 20172:2009 Welding Grouping systems for materials European materials
EN ISO 15609-5:2011 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011, Corrected version 2011-12-01)
ISO 14555:2017 Welding — Arc stud welding of metallic materials
EN ISO 16432:2007 Resistance welding - Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) (ISO 16432:2006)
EN ISO 9692-1:2013 Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013)
EN 14399-8:2007 High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies
EN 10162:2003 Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
ISO 14341:2010 Welding consumables Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels Classification
ISO 2063:2005 Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ISO 14373:2015 Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels
EN 1993-6:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 6: CRANE SUPPORTING STRUCTURES
ISO/TR 3834-6:2007 Quality requirements for fusion welding of metallic materials — Part 6: Guidelines on implementing ISO 3834
ISO 7090:2000 Plain washers, chamfered Normal series Product grade A
ISO 19840:2012 Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces
EN ISO 5817:2014 Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014)
EN 1337-6:2004 Structural bearings - Part 6: Rocker bearings
EN ISO 10511:2012 Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012)
EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051:2010 Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
EN ISO 15614-11:2002 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002)
ISO 15480:1999 Hexagon washer head drilling screws with tapping screw thread
EN ISO 9445-2:2010 Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009)
EN ISO 7049:2011 Cross-recessed pan head tapping screws (ISO 7049:2011)
EN 508-3:2008 Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3: Stainless steel
ISO 1479:2011 Hexagon head tapping screws
EN ISO 7091 : 2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C
EN 1993-4-1:2007/A1:2017 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-1: SILOS
EN ISO 6789:2003 Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003)
EN ISO 7040:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012)
ISO 14343:2017 Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels — Classification
ISO 15980:2002 Open end blind rivets with break pull mandrel and countersunk head — St/St
EN 12385-1:2002+A1:2008 Steel wire ropes - Safety - Part 1: General requirements
EN 10140:2006 Cold rolled narrow steel strip - Tolerances on dimensions and shape
ISO 13920:1996 Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position
EN ISO 7094:2000/AC:2002 PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C
EN 10079:2007 Definition of steel products
EN 14399-3:2015 High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
ISO 10684:2004 Fasteners — Hot dip galvanized coatings
ISO 21670:2014 Fasteners — Hexagon weld nuts with flange
EN ISO 7093-2 : 2000 PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C
ISO 7042:2012 Prevailing torque type all-metal hexagon high nuts — Property classes 5, 8, 10 and 12
ISO 4042:1999 Fasteners Electroplated coatings
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
ISO 15614-13:2012 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 13: Upset (resistance butt) and flash welding
EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
EN 10027-2:2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
EN ISO 9692-2:1998/AC:1999 WELDING AND ALLIED PROCESSES - JOINT PREPARATION - PART 2: SUBMERGED ARC WELDING OF STEELS
ISO 17633:2010 Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels — Classification
EN 15048-1:2016 Non-preloaded structural bolting assemblies - Part 1: General requirements
EN ISO 4042:1999 FASTENERS - ELECTROPLATED COATINGS (ISO 4042:1999)
ISO 15614-11:2002 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 11: Electron and laser beam welding
EN ISO 7092 : 2000 PLAIN WASHERS - SMALL SERIES - PRODUCT GRADE A
EN ISO 15613:2004 Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
EN 1337-4:2004/AC:2007 STRUCTURAL BEARINGS - PART 4: ROLLER BEARINGS
EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
ISO 15620:2000 Welding Friction welding of metallic materials
ISO 15983:2002 Open end blind rivets with break pull mandrel and protruding head — A2/A2
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
ISO 10447:2015 Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds
EN ISO 15612:2004 Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004)
EN 10268:2006+A1:2013 COLD ROLLED STEEL FLAT PRODUCTS WITH HIGH YIELD STRENGTH FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
EN 10056-2:1993 Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions
ISO 14713-1:2017 Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance
ISO 15610:2003 Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables
ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure
EN 1993-1-5:2006/A1:2017 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-5: PLATED STRUCTURAL ELEMENTS
EN 756:2004 Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10244-2:2009 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings
EN ISO 15620:2000 Welding - Friction welding of metallic materials (ISO 15620:2000)
ISO 15979:2002 Open end blind rivets with break pull mandrel and protruding head — St/St
EN ISO 7042:2012 Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012)
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
ISO 2808:2007 Paints and varnishes Determination of film thickness
EN ISO 1481:2011 Slotted pan head tapping screws (ISO 1481:2011)
ISO/TR 15608:2017 Welding Guidelines for a metallic materials grouping system
ISO 2320:2015 Fasteners Prevailing torque steel nuts Functional properties
EN 1714:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS
EN ISO 7090 : 2000 PLAIN WASHERS, CHAMFERED - NORMAL SERIES - PRODUCT GRADE A (ISO 7090:2000)
EN 10279:2000 Hot rolled steel channels - Tolerances on shape, dimensions and mass
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
ISO 2560:2009 Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification
EN ISO 9445-1:2010 Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths (ISO 9445-1:2009)
EN ISO 15979 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD ST/ST
ISO 15984:2002 Open end blind rivets with break pull mandrel and countersunk head — A2/A2
ISO 10509:2012 Hexagon flange head tapping screws
EN 1011-1:2009 Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding
EN 10149-2:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
ISO 14731:2006 Welding coordination Tasks and responsibilities
EN 10034:1993 Structural steel I and H sections - Tolerances on shape and dimensions
EN ISO 7719:2012 Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012)
ISO 7049:2011 Cross-recessed pan head tapping screws
ISO 18276:2017 Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels — Classification
ISO 7976-2:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points
EN 10264-4:2012 Steel wire and wire products - Steel wire for ropes - Part 4: Stainless steel wire
EN ISO 4063:2010 Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01)
EN 1337-2:2004 Structural bearings - Part 2: Sliding elements
EN 10346:2015 Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
ISO/TR 17663:2001 Welding Guidelines for quality requirements for heat treatment in connection with welding and allied processes
EN ISO 7093-1 : 2000 PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A (ISO 7093-1:2000)
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
PREN 10138-3 : DRAFT 2000 PRESTRESSING STEELS - PART 3: STRAND
EN ISO 16834:2012 Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels - Classification (ISO 16834:2012)
EN ISO 18276:2017 Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels - Classification (ISO 18276:2017)
EN ISO 15976 : 2002 CLOSED END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD - ST/ST
EN 10139:2016 Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions
ISO 3443-2:1979 Tolerances for building — Part 2: Statistical basis for predicting fit between components having a normal distribution of sizes
EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
ISO 9013:2017 Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances
EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
EN ISO 9018:2015 DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - TENSILE TEST ON CRUCIFORM AND LAPPED JOINTS (ISO 9018:2015)
EN 10131:2006 (edition 2) Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
ISO 10005:2005 Quality management systems Guidelines for quality plans
EN 10024:1995 Hot rolled taper flange I sections - Tolerances on shape and dimensions
EN 10210-1:2006 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
EN 1337-8:2007 Structural bearings - Part 8: Guide Bearings and Restraint Bearings
EN 1090-1:2009+A1:2011 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
ISO 3834:1978 Welding — Factors to be considered when assessing firms using welding as a prime means of fabrication
EN ISO 1127:1996 Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992)
EN 1011-2:2001/A1:2003 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS
EN 1993-4-3:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
EN 10210-2:2006/AC:2007 HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES
ISO 15612:2004 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure
ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
EN ISO 15611:2003 Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003)
EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 1337-11:1997 Structural bearings - Part 11: Transport, storage and installation
ISO 9692-1:2013 Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
EN ISO 17652-2:2003 Welding - Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers (ISO 17652-2:2003)
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
EN ISO 14373:2015 Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015)
EN 10060:2003 Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
EN 1993-1-4:2006/A1:2015 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS
EN 10169:2010+A1:2012 Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
EN ISO 13920:1996 Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996)
EN 13438:2013 Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes
ISO 15611:2003 Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience
EN 10219-1:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
ISO 1481:2011 Slotted pan head tapping screws
ISO 16834:2012 Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels — Classification
EN 10143:2006 (edition 2) Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
ISO 7089:2000 Plain washers Normal series Product grade A
ISO 16432:2006 Resistance welding Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s)
ISO 9445-2:2009 Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet
EN ISO 14341:2011 Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2010)
EN 10264-3:2012 Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications
EN 10021:2006 General technical delivery conditions for steel products
EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
ISO 4463-1:1989 Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria
ISO 7719:2012 Prevailing torque type all-metal hexagon regular nuts — Property classes 5, 8 and 10
EN 10296-2:2005/AC:2007 WELDED CIRCULAR STEEL TUBES FOR MECHANICAL AND GENERAL ENGINEERING PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: STAINLESS STEEL
EN 1559-2:2014 Founding - Technical conditions of delivery - Part 2: Additional requirements for steel castings
ISO 7091:2000 Plain washers Normal series Product grade C
EN 10017:2004 Steel rod for drawing and/or cold rolling - Dimensions and tolerances
EN 10297-2:2005/AC:2007 SEAMLESS CIRCULAR STEEL TUBES FOR MECHANICAL AND GENERAL ENGINEERING PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: STAINLESS STEEL
CEN ISO/TR 3834-6:2007 Quality requirements for fusion welding of metallic materials - Part 6: Guidelines on implementing ISO 3834 (ISO/TR 3834-6:2007)
EN ISO 2560:2009 Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2009)
EN ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
EN ISO 21670:2014 Fasteners - Hexagon weld nuts with flange (ISO 21670:2014)
EN 1993-5:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 5: PILING
ISO 7092:2000 Plain washers Small series Product grade A
EN ISO 10513:2012 Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012)
EN 1559-1:2011 Founding - Technical conditions of delivery - Part 1: General
EN ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012)
ISO 10513:2012 Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread — Property classes 8, 10 and 12
EN ISO 14713-1:2017 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017)
EN 14399-6:2015 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
EN ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012)
ISO 10512:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread — Property classes 6, 8 and 10
ISO 17632:2015 Welding consumables Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels Classification
ISO 7040:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) — Property classes 5, 8 and 10
EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
EN 10163-3:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
EN ISO 14343:2017 Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017)
EN 10340:2007/AC:2008 STEEL CASTINGS FOR STRUCTURAL USES
EN 1337-3:2005 Structural bearings - Part 3: Elastomeric bearings
EN 13411-4:2011 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
EN 760:1996 Welding consumables - Fluxes for submerged arc welding - Classification
EN ISO 14731:2006 Welding coordination - Tasks and responsibilities (ISO 14731:2006)
EN 14399-1:2015 High-strength structural bolting assemblies for preloading - Part 1: General requirements
EN 10204:2004 Metallic products - Types of inspection documents
EN 12062:1997/A2:2003 NON-DESTRUCTIVE EXAMINATION OF WELDS - GENERAL RULES FOR METALLIC MATERIALS
EN 1993-3-2 : 2006 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 3-2: TOWERS, MASTS AND CHIMNEYS - CHIMNEYS
EN ISO 17632:2015 Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification (ISO 17632:2015)
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
ISO 4997:2015 Cold-reduced carbon steel sheet of structural quality
EN 1600:1997 Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
EN 14399-4:2015 High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies
EN ISO 2063:2005 Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys (ISO 2063:2005)
EN 1993-3-1:2006/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 3-1: TOWERS, MASTS AND CHIMNEYS - TOWERS AND MASTS
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
EN ISO 16433:2007 Resistance welding - Procedure for seam welding of uncoated and coated low carbon steels (ISO 16433:2006)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
EN 1993-1-3:2006/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD-FORMED MEMBERS AND SHEETING
ISO 14554-1:2013 Quality requirements for welding — Resistance welding of metallic materials — Part 1: Comprehensive quality requirements
ISO 17652-2:2003 Welding Test for shop primers in relation to welding and allied processes Part 2: Welding properties of shop primers
EN 10025-6:2004+A1:2009 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
EN 1713:1998/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - CHARACTERIZATION OF INDICATIONS IN WELDS
ISO 14175:2008 Welding consumables — Gases and gas mixtures for fusion welding and allied processes
ISO 7976-1:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments
ISO 15609-5:2011 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding
EN 1993-4-2:2007/A1:2017 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-2: TANKS
ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
EN ISO 15614-13:2012 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012)
EN 10020:2000 Definition and classification of grades of steel
EN 1993-1-9:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE
ISO 6789:2003 Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure
ISO 15976:2002 Closed end blind rivets with break pull mandrel and protruding head — St/St
EN 10219-2:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties
ISO 3443-1:1979 Tolerances for building — Part 1: Basic principles for evaluation and specification
EN 12385-10:2003+A1:2008 Steel wire ropes - Safety - Part 10: Spiral ropes for general structural applications
EN 14399-7:2007 High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies
EN 10061:2003 Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions
EN 10059:2003 Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions
EN 1337-7:2004 Structural bearings - Part 7: Spherical and cylindrical PTFE bearings
CEN/TR 10347:2006 Guidance for forming of structural steels in processing
ISO 16433:2006 Resistance welding Procedure for seam welding of uncoated and coated low carbon steels
ISO 9692-2:1998 Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels
EN ISO 15609-4:2009 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding (ISO 15609-4:2009)
EN ISO 10684:2004/AC:2009 Fasteners - Hot dip galvanized coatings (ISO 10684:2004/Cor 1:2008)
EN ISO 15980 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD ST/ST
ISO 7093-2:2000 Plain washers Large series Part 2: Product grade C
EN 14399-5:2015 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
EN 14295 : 2003 WELDING CONSUMABLES - WIRE AND TUBULAR CORED ELECTRODES AND ELECTRODE-FLUX COMBINATIONS FOR SUBMERGED ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
EN 1993-1-2:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN
ISO 4063:2009 Welding and allied processes — Nomenclature of processes and reference numbers
EN ISO 15480 : 1999 HEXAGON WASHER HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD
EN ISO 636:2017 Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO 636:2017)
ISO 14713-2:2009 Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing
EN 10055:1995 Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions
EN ISO 14555:2017 Welding - Arc stud welding of metallic materials (ISO 14555:2017)
EN ISO 15610:2003 Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003)
EN 1998-1:2004/A1:2013 EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 1: GENERAL RULES, SEISMIC ACTIONS AND RULES FOR BUILDINGS
ISO 3443-3:1987 Tolerances for building — Part 3: Procedures for selecting target size and predicting fit
EN 1990:2002/A1:2005/AC:2010 EUROCODE - BASIS OF STRUCTURAL DESIGN
EN ISO 9013:2017 Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017)
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
ISO 9445-1:2009 Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN ISO 7089 : 2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE A
EN 10160:1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
ISO 13916:2017 Welding — Measurement of preheating temperature, interpass temperature and preheat maintenance temperature
EN 970:1997 Non-destructive examination of fusion welds - Visual examination
ISO 1803:1997 Building construction Tolerances Expression of dimensional accuracy Principles and terminology
EN 1993-1-8:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
EN ISO 15984 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD A2/A2
EN 1290:1998/A2:2003 NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS
EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 1337-5:2005 Structural bearings - Part 5: Pot bearings
EN 1993-1-7:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-7: PLATED STRUCTURES SUBJECT TO OUT OF PLANE LOADING
ISO 2859-5:2005 Sampling procedures for inspection by attributes Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
EN ISO 15983 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD A2/A2
ISO 15609-4:2009 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding
EN 1993-1-12:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-12: ADDITIONAL RULES FOR THE EXTENSION OF EN 1993 UP TO STEEL GRADES S 700
ISO 636:2017 Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification
EN 13670:2009 Execution of concrete structures
EN 15311:2007 Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
EN 1993-2:2006/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 2: STEEL BRIDGES
EN ISO 10512:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)
EN 14616:2004 Thermal spraying - Recommendations for thermal spraying
EN 10149-3:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
EN 1993-1-10:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-10: MATERIAL TOUGHNESS AND THROUGH-THICKNESS PROPERTIES
EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
EN 757:1997 Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification
EN 1993-1-11:2006/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-11: DESIGN OF STRUCTURES WITH TENSION COMPONENTS
EN ISO 10447:2015 Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2015)
EN 13479:2017 Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials
EN 1435:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - RADIOGRAPHIC TESTING OF WELDED JOINTS
EN ISO 2808:2007 Paints and varnishes - Determination of film thickness (ISO 2808:2007)
EN 508-1:2014 Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
EN 14399-2:2015 High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
ISO 1127:1992 Stainless steel tubes Dimensions, tolerances and conventional masses per unit length
ISO 7093-1:2000 Plain washers Large series Part 1: Product grade A
EN ISO 14713-2:2009 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)
EN ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009)
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels
EN ISO 14175:2008 Welding consumables - Gases and gas mixtures for fusion welding and allied processes (ISO 14175:2008)

View more information
£199.51
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.