• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 12418:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

MASONRY AND STONE CUTTING-OFF MACHINES FOR JOB SITE - SAFETY
Available format(s)

Hardcopy , PDF

Superseded date

20-01-2022

Language(s)

English

Published date

25-08-2000

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
  5.1 Mechanical hazard
  5.2 Electrical hazards
  5.3 Thermal hazards
  5.4 Exhaust fumes (and gas)
  5.5 Fluid containers
  5.6 Protection against water splashes
  5.7 Rotational speed
  5.8 Noise
  5.9 Maintenance
6 Verification of safety requirements and/or measures
7 Information for use
  7.1 Marking
  7.2 Accompanying documents
Annex A (normative) Noise test code - Grade 2 of accuracy
Annex B (normative) Dimensions of the flanges for cutting-off
        diamond wheel
Annex C (normative) Strength of guards - State of the art
        concerning the characteristics of guards used with
        cutting-off wheels
Annex D (normative) Pictograms
Annex E (normative) Verification of surface temperature
Annex F (normative) Vibration test code
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 98/37/EC, amended by 98/79/EC
Annex ZB (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 2006/42/EC
Bibliography

Applies to transportable masonry and stone cutting-off machines stationary during work, principally used on job site building construction for cutting-off stones, other mineral construction materials and composite materials having at least one supporting surface.

DevelopmentNote
2000 Edition Re-Issued in May 2009 & incorporates AMD 1 2009. (06/2009)
DocumentType
Standard
Pages
42
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

EN 12096:1997 Mechanical vibration - Declaration and verification of vibration emission values
PREN ISO 3744 : DRAFT 2009 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHOD IN AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 5349-2:2001 Mechanical vibration Measurement and evaluation of human exposure to hand-transmitted vibration Part 2: Practical guidance for measurement at the workplace
ISO 20643:2005 Mechanical vibration — Hand-held and hand-guided machinery — Principles for evaluation of vibration emission
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 13218:2002+A1:2008/AC:2010 MACHINE TOOLS - SAFETY - STATIONARY GRINDING MACHINES
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
IEC 61029-1:1990 Safety of transportable motor-operated electric tools - Part 1: General requirements
EN ISO 5349-2:2001/A1:2015 MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF HUMAN EXPOSURE TO HAND-TRANSMITTED VIBRATION - PART 2: PRACTICAL GUIDANCE FOR MEASUREMENT AT THE WORKPLACE (ISO 5349 2:2001/AMD 1:2015)
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 20643:2008/A1:2012 Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission - Amendment 1: Accelerometer positions (ISO 20643:2005/Amd 1:2012)
EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 8041:2005/AC:2008 HUMAN RESPONSE TO VIBRATION - MEASURING INSTRUMENTATION
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
ISO 16063-1:1998 Methods for the calibration of vibration and shock transducers Part 1: Basic concepts
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
ISO 8041:2005 Human response to vibration Measuring instrumentation
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
EN 61029-1:2009/A11:2010 SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN 60335-2-41:2003/A2:2010 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-41: PARTICULAR REQUIREMENTS FOR PUMPS
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
IEC 60335-2-41:2012 Household and similar electrical appliances - Safety - Part 2-41: Particular requirements for pumps

View more information
£69.55
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.