• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 12478:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF MACHINE TOOLS - LARGE NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES
Available format(s)

Hardcopy , PDF

Superseded date

04-06-2010

Language(s)

English

Published date

01-01-2000

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) Noise emission measurement
Annex ZA (informative) Clauses of this European Standard
                       addressing essential requirements
                       or other provisions of EU directives
Bibliography

Defines the requirements and/or measures to remove the hazards and limit the risks on general purpose numerically controlled large turning machines and turning centres which are designed primarily to work cold metal as defined in 3.1 and 3.2 and herein after referred to as "machines".

DocumentType
Standard
Pages
42
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

EN 294:1992/AC:1993 SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS
EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 418 : 1992 SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
EN 12840 : 2001 SAFETY OF MACHINE-TOOLS - MANUALLY CONTROLLED TURNING MACHINES WITH OR WITHOUT AUTOMATIC CONTROL
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
EN 12626 : 1997 SAFETY OF MACHINERY - LASER PROCESSING MACHINES - SAFETY REQUIREMENTS
EN 547-2:1996+A1:2008 Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
IEC 61511-1:2016+AMD1:2017 CSV Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements
EN 1837:1999+A1:2009 Safety of machinery - Integral lighting of machines
EN 999:1998+A1:2008 Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN 547-1:1996+A1:2008 Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery
IEC 61508-5:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 5: Examples of methods for the determination of safety integrity levels (see Functional Safety and IEC 61508)
EN 1550:1997+A1:2008 Machine-tools safety - Safety requirements for the design and construction of work holding chucks
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
EN 414 : 2000 SAFETY OF MACHINERY - RULES FOR THE DRAFTING AND PRESENTATION OF SAFETY STANDARDS
IEC 61508-4:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508)
IEC 61508-3:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements (see Functional Safety and IEC 61508)
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN 292-1 : 1991 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY
EN 574:1996+A1:2008 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
ISO 447:1984 Machine tools Direction of operation of controls
IEC 61511-3:2016 Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 547-3:1996+A1:2008 Safety of machinery - Human body measurements - Part 3: Anthropometric data
IEC 61511-2:2016 Functional safety - Safety instrumented systems for the process industry sector - Part 2: Guidelines for the application of IEC 61511-1:2016
ISO 1219-1:2012 Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications
ISO 2972:1979 Numerical control of machines — Symbols
ENV 26385 : 1990 ERGONOMIC PRINCIPLES OF THE DESIGN OF WORK SYSTEMS
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 954-1 : 1996 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
IEC 61508-6:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 (see Functional Safety and IEC 61508)
EN 292-2 : 91 AMD 1 95 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
IEC 61508-7:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508)
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 14122-1:2016 Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
EN ISO 9614-1:2009 Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
IEC 61508-2:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508)
EN 1070 : 1998 SAFETY OF MACHINERY - TERMINOLOGY
ISO 230-5:2000 Test code for machine tools Part 5: Determination of the noise emission
EN 692:2005+A1:2009 Machine tools - Mechanical presses - Safety
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
£58.57
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.