I.S. EN 13020:2015
Current
The latest, up-to-date edition.
ROAD SURFACE TREATMENT MACHINES - SAFETY REQUIREMENTS
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
Annex A (informative) - Truck attachment plate
Annex B (informative) - Terminology
Annex C (informative) - Examples of technical measures
to reduce noise
Annex D (normative) - Noise test code for the declaration
of noise emission values (grade of accuracy)
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Covers all significant hazards identified through a risk assessment relevant to road surface treatment machines when they are used as intended and under the conditions foreseen by the manufacturer.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NF EN 13020 : 2016 | Identical |
| UNI EN 13020 : 2010 | Identical |
| NS EN 13020 : 2015 | Identical |
| SN EN 13020 : 2016 | Identical |
| EN 13020:2015 | Identical |
| NEN EN 13020 : 2015 | Identical |
| DIN EN 13020:2016-02 | Identical |
| NBN EN 13020 : 2015 | Identical |
| UNE-EN 13020:2016 | Identical |
| BS EN 13020:2015 | Identical |
| ISO 12098:2004 | Road vehicles Connectors for the electrical connection of towing and towed vehicles 15-pole connector for vehicles with 24 V nominal supply voltage |
| EN ISO 2860:2008 | Earth-moving machinery - Minimum access dimensions (ISO 2860:1992) |
| EN 500-1:2006+A1:2009 | Mobile road construction machinery - Safety - Part 1: Common requirements |
| EN ISO 15667 : 2000 | ACOUSTICS - GUIDELINES FOR NOISE CONTROL BY ENCLOSURES AND CABINS |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 14119:2013 | Safety of machinery Interlocking devices associated with guards Principles for design and selection |
| ISO 730:2009 | Agricultural wheeled tractors — Rear-mounted three-point linkage — Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4 |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN ISO 14163 : 1998 | ACOUSTICS - GUIDELINES FOR NOISE CONTROL BY SILENCERS |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN ISO 3457:2008 | Earth-moving machinery - Guards - Definitions and requirements (ISO 3457:2003) |
| ISO 15667:2000 | Acoustics Guidelines for noise control by enclosures and cabins |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN ISO 11820 : 1996 | ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2 : 2000 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 2860:1992 | Earth-moving machinery — Minimum access dimensions |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 3457:2003 | Earth-moving machinery Guards Definitions and requirements |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 14119:2013 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013) |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 14163:1998 | Acoustics — Guidelines for noise control by silencers |
| ISO 1724:2003 | Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 N (normal) for vehicles with 12 V nominal supply voltage |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 11546-1:1995 | Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes) |
| EN ISO 2867:2011 | Earth-moving machinery - Access systems (ISO 2867:2011) |
| ISO 3731:2003 | Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 S (supplementary) for vehicles with 24 V nominal supply voltage |
| ISO 1185:2003 | Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 N (normal) for vehicles with 24 V nominal supply voltage |
| EN ISO 11546-1:2009 | Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 2867:2011 | Earth-moving machinery Access systems |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 894-4:2010 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 6750:2005 | Earth-moving machinery Operator's manual Content and format |
| ISO 8759-2:1998 | Agricultural wheeled tractors — Front-mounted equipment — Part 2: Stationary equipment connection |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.