Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

I.S. EN 13244-3:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - FITTINGS
Available format(s)

Hardcopy , PDF

Superseded date

14-09-2011

Language(s)

English

Published date

01-01-2002

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
   4.1 PE compound
   4.2 Material for non-polyethylene parts
        4.2.1 General
        4.2.2 Metal parts
        4.2.3 Elastomers
        4.2.4 Other materials
5 General characteristics
   5.1 Appearance
   5.2 Design
   5.3 Colour
   5.4 Electrical characteristics for electrofusion
        fittings
   5.5 Appearance of factory made joints
6 Geometrical characteristics
   6.1 Measurement of dimensions
   6.2 Dimensions of electrofusion sockets
        6.2.1 Diameters and lengths of electrofusion
              sockets
        6.2.2 Wall thicknesses
   6.3 Dimensions of spigotted fittings
   6.4 Dimensions of socket fusion fittings
   6.5 Socketed pipe
        6.5.1 Dimensions and tolerances of the socket
              and length of spigot end
        6.5.2 Equations for calculating the dimensions
              of sockets of non-end-load-resistant
              fittings for use with pipes up to 6 m
              lengths
   6.6 Dimensions of mechanical fittings
   6.7 Dimensions of loose backing flanges and flange
        adapters
7 Mechanical characteristics
   7.1 General
   7.2 Conditioning
   7.3 Requirements
   7.4 Retest in case of failure at 80 degree C
   7.5 Pressure drop
8 Physical characteristics
   8.1 Conditioning
   8.2 Requirements
9 Chemical characteristics of fittings in contact with
   chemicals
10 Sealing rings
11 Performance requirements
12 Marking
   12.1 General
   12.2 Minimum required marking of fittings
   12.3 Minimum required marking on a label
   12.4 Fusion system recognition
13 Packaging
Annex A (normative) Socket fusion fittings
Annex B (informative) Examples of typical terminal
        connection for electrofusion fittings
Bibliography

Gives the characteristics of fittings made from polyethylene (PE) intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage.

DocumentType
Standard
Pages
30
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
NS EN 13244-3 : 1ED 2003 Identical
NF EN 13244-3 : 2003 Identical
UNI EN 13244-3 : 2004 Identical
EN 13244-3:2002 Identical
NBN EN 13244-3 : 2003 Identical
UNE-EN 13244-3:2003 Identical
SN EN 13244-3 : 2003 Identical
NEN EN 13244-3 : 2003 Identical
BS EN 13244-3:2002 Identical
DIN EN 13244-3:2003-05 Identical

EN 13244-1:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
ISO 4433-1:1997 Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method
EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
EN 921:1994/AC:1995 PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE
ISO 4433-2:1997 Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes
ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
PREN ISO 3126 : DRAFT 1999 PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
ISO 9624:1997 Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
ISO 4059:1978 Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements
EN 13244-5:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 13244-2:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes

View more information
£58.57
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us