• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 1452-2:1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES
Available format(s)

Hardcopy , PDF

Superseded date

29-12-2009

Language(s)

English

Published date

01-01-1999

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
      4.1 Pipe material
      4.2 Density
      4.3 MRS-value
5 General characteristics
      5.1 Appearance
      5.2 Colour
      5.3 Opacity
6 Geometrical characteristics
      6.1 Measurement of dimensions
      6.2 Nominal outside diameters
      6.3 Mean outside diameters and their tolerances
      6.4 Wall thicknesses and their tolerances
      6.5 Length of pipe
      6.6 Pipes with sockets
      6.7 Pipe ends for ring seal or solvent cement
             joints
7 Classification and selection of pipes
      7.1 Classification
      7.2 Selection of the nominal pressure PN and of the
             pipe series S for water up to approximately 20
             degree C
      7.3 Determination of the allowable operating
             pressure PFA for water up to 45 degree C
8 Mechanical characteristics
      8.1 Impact strength
      8.2 Resistance to internal pressure
9 Physical characteristics
10 Chemical characteristics
11 Sealing rings
12 Adhesives
13 Performance requirements
14 Marking
      14.1 General
      14.2 Minimum required marking
      14.3 Additional marking
Annex A (normative) Allowable operating pressures
Annex B (normative) Imperial(inch)-sized pipes
Annex C (normative) Requirements for fracture toughness test
Annex D (informative) Bibliography

Defines the characteristics of pipes made from unplasticized poly (vinyl chloride) (PVC-U) for piping systems in the field of water supply. Test parameters for the test methods referred to in this standard are also defined. In conjunction with Parts 1 to 5 of EN1452-7, it is applicable to extruded PVC-U pipes without a socket and pipes with a socket (integral or not, intended to be used for the following: conveyance of water above ground for both outside and inside buildings; water mains and services buried in ground; for the supply of water under pressure at approximately 20 deg C (cold water) intended for human consumption and for general purposes. Applicable to pipes for the conveyance of water up to and including 45 deg C. For temperature between 25 and 45 deg C. Figure A1 in Annex A applies.

DocumentType
Standard
Pages
38
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
NF EN 1452-2 : 1999 Identical
EN 1452-2 : 1999 Identical
DIN EN 1452-2:1999-09 Identical
NEN EN 1452-2 : 1999 Identical
SN EN 1452-2 : 1999 Identical
NBN EN 1452-2 : 2000 Identical
NS EN 1452-2 : 1999 Identical
BS EN 1452-2 : 2000 Identical
UNI EN 1452-2 : 2001 Identical

View more information
£58.57
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.