I.S. EN 15094:2008
Current
The latest, up-to-date edition.
SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR COLD FLAT ROLLING MILLS
Hardcopy , PDF
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety Requirements and/or measures
5.1 General requirements for design, planning and risk assessment
5.1.1 Planning of cold flat rolling mills
5.1.2 Structural assembly
5.1.3 Safety layout
5.1.4 Access to operating points
5.1.5 Access to danger zones
5.1.6 Guards
5.1.7 Guard-rails
5.1.8 Safety signs and warning devices
5.1.9 Safe guarding
5.1.10 Personal protective equipment
5.1.11 Electrical equipment
5.1.12 Hydraulic, pneumatic, cooling and lubrication systems
5.1.13 Fluid systems
5.1.14 Material to be discharged to drains
5.1.15 Surface temperatures and heat radiation
5.1.16 Pulpits and control stands
5.1.17 Software manipulation
5.1.18 Fire protection
5.1.19 Ergonomic principles
5.1.20 Vibrations
5.1.21 Loss of energy
5.1.22 Linked Equipment
5.2 List of significant hazards, hazardous situations, safety
requirements and/or measures
5.2.1 General
5.2.2 Hydraulics, pneumatics, emulsions and other
pressurised fluid systems
5.2.3 Bridges over roller tables and material guides
5.2.4 Handling, guiding and transfer equipment (general)
5.2.5 Roller tables and conveyors
5.2.6 Rolling mills, rolling mill stands
5.2.7 Pulpits and control stands
5.2.8 Measuring devices and display units
5.2.9 Cutting devices
5.2.10 Coiling/de-coiling equipment
5.2.11 Coil banding machines and marking machines
5.3 Additional safety requirements or measures
5.3.1 Hold-to-run control device
5.3.2 Mechanical restraint devices
5.3.3 Accessible rotating/moving parts
5.3.4 Particular ergonomic requirements
5.4 Noise reduction as a safety requirement
5.4.1 Noise reduction at source by design
5.4.2 Noise reduction by protective measures
5.4.3 Noise reduction by information
5.4.4 Noise sources and examples of noise reduction
measures
6 Verification of the safety requirements and/or measures
7 Information for use
7.1 General
7.2 Warning devices and safety signs
7.3 Minimum marking
7.4 Accompanying documents
7.4.1 Instruction handbook
7.4.2 Machine/equipment declaration
7.4.3 Detailed information/instructions
7.5 Maintenance manual
Annex A (normative) Safety requirements and/or measures for
electrical equipment and control systems at cold
rolling mills
A.1 General
A.2 Special requirements for controls
A.3 Special requirements for shut-down equipment
A.3.1 Stop functions/emergency stop functions
A.3.2 Selection of stop functions
A.3.3 Emergency stop areas
A.3.4 Stop functions
Annex B (normative) Noise test code
B.1 Introduction
B.2 Determination of A-weighted sound power level
B.3 Determination of A-weighted emission sound pressure
levels
B.3.1 Determination of the emission sound pressure
level at specified measuring points
B.3.2 Determination of emission sound pressure level
at work stations
B.4 Measurement uncertainty
B.5 Operating conditions
B.6 Information to be recorded and reported
B.7 Declaration and verification of noise emission values
Annex C (normative) Protection of persons in case of using
asphyxiant gases in fire fighting systems
C.1 General
C.2 Warning devices
C.3 Restraint devices
C.4 Preliminary warning time
C.5 Interrupt device for extinguishing gas
C.6 Blocking devices
C.7 Pipes
C.8 Rooms and adjacent areas
C.9 Escape routes
C.10 Doors
C.11 Marking
C.12 Instruction handbook
Annex D (informative) Example for manufacturer's safety instructions
for maintenance at cold flat rolling mills
D.1 Precautions to reduce hazards caused by
D.1.1 Lack of instructions
D.1.2 Visual or audible checks at machinery in motion
D.1.3 Unintentional movements during maintenance
D.1.4 Work during standstill with safeguards disabled
D.1.5 Work with hazardous substances
D.1.6 Plant re-start
Annex E (informative) Machines and/or equipment covered by
this standard
E.1 Machines and/or equipment covered by this standard
but are not limited to
E.1.1 Plants
E.1.2 Equipment
Annex F (informative) Roll spalling
F.1 Hazard
F.2 Causes
F.3 Safety measures
Annex G (informative) Example for the risk analysis due to
interfaces
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.