• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 15632-1:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 1: CLASSIFICATION, GENERAL REQUIREMENTS AND TEST METHODS
Available format(s)

Hardcopy , PDF

Superseded date

07-06-2022

Language(s)

English

Published date

23-02-2009

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Requirements
6 Test methods
7 Marking
8 Manufacturer's information
Annex A (normative) - Thermal conductivity of
        pre-insulated pipes - Test procedure
Annex B (normative) - Calculation of the heat flow from
        the medium to the ambient loss of pre-insulated
        buried district heating pipes
Annex C (informative) - Determination of design values for
        the radial thermal resistance
Annex D (informative) - Guideline for testing
Bibliography

Gives classification, general requirements and test methods for flexible, pre-insulated, directly buried district heating pipe systems.

DevelopmentNote
2009 Edition Re-Issued in January 2015 & incorporates AMD 1 2014. (02/2015)
DocumentType
Standard
Pages
34
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
EN 15632-1:2009+A1:2014 (edition 2) Identical

EN 13941:2009+A1:2010 Design and installation of preinsulated bonded pipe systems for district heating
EN 12667:2001 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance
EN 12085:2013 Thermal insulating products for building applications - Determination of linear dimensions of test specimens
EN 1295-1:1997 Structural design of buried pipelines under various conditions of loading - Part 1: General requirements
EN ISO 23993:2010 Thermal insulation products for building equipment and industrial installations - Determination of design thermal conductivity (ISO 23993:2008, Corrected version 2009-10-01)
EN 1606:2013 Thermal insulating products for building applications - Determination of compressive creep
IEC 60811-4-1:2004 Insulating and sheathing materials of electric and optical cables - Common test methods - Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope
EN ISO 9967:2016 Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016)
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
EN ISO 8497:1996 Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994)
ISO 23993:2008 Thermal insulation products for building equipment and industrial installations — Determination of design thermal conductivity
ISO 16770:2004 Plastics Determination of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT)
EN 1605:2013 Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions
EN ISO 16871:2003 Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003)
ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
ISO 8497:1994 Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes
EN 14419:2009 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Surveillance systems
ISO 16871:2003 Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering
EN 489:2009 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
EN 744:1995 Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method
EN 60811-4-1:2004 Insulating and sheathing materials of electric and optical cables - Common test methods - Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
EN 253:2009+A2:2015 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness

View more information
£54.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.