I.S. EN 1726-1:1999
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
04-09-2012
English
01-01-1999
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
3.1 Operator
3.2 Normal operating position
3.3 Low-lift height
3.4 Automatically acting brakes
3.5 Normal operating conditions
3.6 Rated capacity
3.7 Actual capacity
3.8 Standard lift height
3.9 Standard load centre distance
3.10 Rated drawbar pull of tractors
3.11 Forward driving direction and front end
4 List of hazards
5 Requirements
5.1 General
5.2 Starting/Moving
5.3 Brakes
5.4 Controls
5.5 Power systems and accessories
5.6 Systems for lifting and tilting
5.7 Operator position
5.8 Stability
5.9 Protective devices
5.10 Visibility/Lighting
5.11 Environmental conditions
6 Verification of safety requirements and/or measures
6.1 General
6.2 Structural verification
6.3 Functional verification
7 Information for use
7.1 Residual hazards
7.2 Instruction handbook
7.3 Minimum marking
Annex A (normative) Verification of steering wheel
kickback
A.1 Scope
A.2 Test conditions
A.2.1 General
A.2.2 Area
A.2.3 Obstacle
A.2.4 Reaction measurement
A.3 Test procedure
A.4 Results
Annex B (normative) Counterbalanced trucks with articulated
steering - Verification of stability
B.1 Scope
B.2 Conditions of validity
B.3 Test conditions
B.3.1 Test procedure
B.3.2 Conditions of the truck
B.3.3 Effect of the operator's weight on stability
B.3.4 Location of the truck on the test platform
B.3.5 Test load
B.3.6 Safety precautions
B.4 Test procedure
B.5 Tests for trucks fitted with attachments
Annex C (normative) Reach and straddle trucks - Verification
of stability
C.1 Conditions of validity
C.2 Test procedure
Annex D (normative) Pallet stackers and high lift platform
trucks - Verification of stability
D.1 Conditions of validity
D.2 Test procedure
Annex E (normative) Single side loading fork lift trucks
- Verification of stability
E.1 Scope
E.2 Conditions of validity
E.3 Test conditions
E.3.1 Test procedure
E.3.2 Conditions of the truck
E.3.3 Effect of the operator's weight on stability
E.3.4 Location of the truck on the test platform
E.3.5 Test load
E.3.6 Safety precautions
E.4 Test procedure
E.5 Tests for trucks fitted with attachments
Annex F (normative) Bi-directional and multi-directional
trucks - Verification of stability
F.1 Scope
F.2 Conditions of validity
F.3 Test conditions
F.3.1 Test procedure
F.3.2 Conditions for the truck
F.3.3 Effect of the operator's weight on stability
F.3.4 Location of the truck on the test platform
F.3.5 Test load
F.3.6 Safety precautions
F.4 Test procedure
F.5 Tests for trucks fitted with attachments
Annex G (normative) Lateral and front stacking trucks -
Verification of stability
G.1 Scope
G.2 Conditions of validity
G.2.1 General
G.2.2 Normal operating conditions
G.3 Test conditions
G.3.1 Test procedure
G.3.2 Conditions for the truck
G.3.3 Effect of the operator's weight on stability
G.3.4 Location of the truck on the test platform
G.3.5 Test load
G.3.6 Safety precautions
G.4 Test procedure
G.5 Tests for trucks fitted with attachments
Annex H (normative) Rough terrain trucks - Verification
of stability
H.1 Scope
H.2 Conditions of validity
H.3 Test conditions
H.3.1 Test procedure
H.3.2 Conditions for the truck
H.3.3 Effect of the operator's weight on stability
H.3.4 Location of the truck on the test platform
H.3.5 Test load
H.3.6 Safety precautions
H.4 Test procedure
H.5 Tests for trucks fitted with attachments
Annex J (normative) Industrial trucks operating in special
conditions of stacking with load offset by powered
devices - Additional verification of the stability
Annex K (normative) Trucks operated with masts tilted
forward - Verification of stability
Annex L (normative) Trucks operating with offset load -
Offset determined by the utilization
L.1 Scope
L.2 Conditions of validity
L.3 Test conditions
L.3.1 Test procedure
L.3.2 Conditions for the truck
L.3.3 Effect of the operator's weight on stability
L.3.4 Location of the truck on the test platform
L.3.5 Test load
L.3.6 Safety precautions
L.4 Test procedure
L.5 Tests for trucks fitted with attachments
Annex M (normative) Verification of overhead guard -
Impact drop test
M.1 Scope
M.2 Test conditions
M.2.1 Test load
M.2.2 Test procedure
M.2.3 Requirements
Annex N (informative) Loading control
Annex O (normative) Seat belt - Requirements and test
procedure
O.1 Scope
O.2 Terms and definitions
O.3 Requirements
O.3.1 Performance requirements
O.3.2 Specific requirements for the strap
O.4 Test equipment
O.4.1 Test body block
O.5 Test method
O.5.1 Lateral pull test
O.5.2 Forward pull test
O.5.3 Retractor locking device
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or other
provisions of EU Directives
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.