• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 1870-2:1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 2: HORIZONTAL BEAM PANEL SAWS AND VERTICAL PANEL SAWS
Available format(s)

Hardcopy , PDF

Superseded date

08-02-2008

Language(s)

English

Published date

01-01-1999

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
0 Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 Safety requirements and/or measures
  5.1 Controls
  5.2 Protection against mechanical hazards
  5.3 Protection against non-mechanical hazards
6 Information for use
  6.1 Warning devices
  6.2 Marking
  6.3 Instruction handbook
Annex A (normative) Dimensional tolerances of saw spindles
Annex B (normative) Riving knife mounting strength test
Annex C (normative) Riving knife lateral stability test
Annex D (normative) Rigidity test for sectional safety
        curtain material
Annex E (informative) Safe working practice
Annex ZA (informative) Clauses of this European Standard
         addressing essential requirements or other provisions
         of EU directives

Defines the measurement and/or requirements to remove the hazards and limit the risks of manual loaded and/or unloaded horizontal beam panel saws and vertical panel saws, designed to cut solid wood, fibreboard, chipboard, plywood and also the materials where they are covered with plastic edging and/or plastic/light alloy laminates.

DocumentType
Standard
Pages
51
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

EN 294:1992/AC:1993 SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS
EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN 418 : 1992 SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 7960:1995 Airborne noise emitted by machine tools Operating conditions for woodworking machines
EN 1760-1:1997+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
EN 292-1 : 1991 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY
HD 22-1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS
HD 21.1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 847-1:2017 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 954-1 : 1996 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
EN ISO 3743-1:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
EN 292-2 : 91 AMD 1 95 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 3745:2012 Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
EN ISO 9614-1:2009 Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
£75.04
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.