Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
NSAI
I.S. EN 1917:2002

I.S. EN 1917:2002

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CONCRETE MANHOLES AND INSPECTION CHAMBERS, UNREINFORCED, STEEL FIBRE AND REINFORCED

Available format(s)

Hardcopy , PDF

Superseded date

06-03-2020

Language(s)

English

Published date

01-01-2002

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
5 Special requirements
6 Test methods for finished products
7 Conformity evaluation
8 Marking
Annex A (normative) - Test method for crushing strength of
        chamber and shaft units
Annex B (normative) - Test methods for vertical strength of
        reducing units and capping units
Annex C (normative) - Test methods for watertightness
Annex D (normative) - Test method for water absorption
Annex E (normative) - Test methods for installed steps
Annex F (normative) - Manufacturer's quality assurance system
Annex G (normative) - Sampling procedures for inspection of
        finished products
Annex H (normative) - Sampling procedures for continuous
        inspection of crushing strength, vertical strength
        and watertightness (vertical unit hydrostatic)
Annex I (normative) - Tasks for a product certification body
Annex J (normative) - Procedure for unreinforced concrete
        chamber and shaft units where routine (continuous)
        inspection of crushing strength is primarily to
        minimum crushing load
Annex ZA (informative) - Clauses of this European Standard
         addressing essential requirements or other provisions
         of EU Directives
Bibliography

Describes performance requirements as defined in Table 1 and describes test methods for precast concrete units for inspection chambers designed to be used for inverts not exceeding 2 metres deep and manholes, of circular, rectangular (with or without chamfered or rounded corners) or elliptical internal shape, unreinforced, steel fibre and reinforced, with nominal sizes and normal length not exceeding DN 1 250 (circular) or LN 1 250 (rectangular or elliptical).

DocumentType
Standard
Pages
108
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
UNI EN 1917 : 2004 Identical
SN EN 1917 : 2002 Identical
UNE-EN 1917:2008 Identical
NF EN 1917 : 2003 Identical
DIN EN 1917:2003-04 Identical
BS EN 1917:2002 Identical
NBN EN 1917 : 2002 COR 2008 Identical
NEN EN 1917 : 2002 C3 2008 Identical
NS EN 1917 : 2002 AC 2008 Identical
EN 1917:2002/AC:2008 Identical

I.S. 420:2004 PRE-CAST CONCRETE MANHOLES

EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
ISO/IEC Guide 62:1996 General requirements for bodies operating assessment and certification/registration of quality systems
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 12491:1997 Statistical methods for quality control of building materials and components
ISO 3951:1989 Sampling procedures and charts for inspection by variables for percent nonconforming
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 9001:2015 Quality management systems — Requirements
ISO 4012:1978 Concrete — Determination of compressive strength of test specimens
ISO 10544:1992 Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric
EN 1916:2002/AC:2008 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS

View more information
£98.84
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us