• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 60384-1:2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
Available format(s)

Hardcopy , PDF

Superseded date

23-09-2021

Language(s)

English

Published date

01-01-2016

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
FOREWORD
INTRODUCTION
1 General
2 Technical data
3 Quality assessment procedures
4 Tests and measurement procedures
Annex A (informative) - Interpretation of sampling plans
        and procedures as described in IEC 60410 for use
        within quality assessment systems
Annex B (informative) - Rules for the preparation of
        detail specifications for capacitors and resistors
        for electronic equipment for use within quality
        assessment systems
Annex C (informative) - Layout of the first page of a
        PCP/CQC specification
Annex D (informative) - Requirements for capability approval
        test report
Annex E (informative) - Guide for pulse testing of capacitors
Annex F (informative) - Guidance for the extension of
        endurance tests on fixed capacitors
Annex G (normative) - Damp heat, steady state with voltage
        applied, for metallized film capacitors only
Annex H (normative) - Accelerated damp heat, steady state,
        for multilayer ceramic capacitors only
Annex Q (informative) - Quality assessment procedures
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Defines standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

DevelopmentNote
Supersedes I.S. EN 130000. (01/2003) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
186
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
BS EN 60384-1:2016 Identical
SN EN 60384-1 : 2016 Identical
DIN EN 60384-1 : 2017 Identical
NF EN 60384-1 : 2016 Identical
EN 60384-1:2016 Identical
NBN EN 60384-1 : 2016 Identical

IEC 61193-2:2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages
HD 323.2.20 : 200S3 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST T - SOLDERING
EN ISO 80000-1:2013 Quantities and units - Part 1: General (ISO 80000-1:2009 + Cor 1:2011)
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60068-2-58:2015+AMD1:2017 CSV Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
IECQ 001002-3:2005 IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES
IEC 61249-2-7:2002 Materials for printed boards and other interconnecting structures - Part 2-7: Reinforced base materials clad and unclad - Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
ISO 3:1973 Preferred numbers Series of preferred numbers
EN 61249-2-7:2002/corrigendum:2005 MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-7: REINFORCED BASE MATERIALS CLAD AND UNCLAD - EPOXIDE WOVEN E-GLASS LAMINATED SHEET OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD
IEC 60469-1:1987 Pulse techniques and apparatus. Part 1: Pulse terms and definitions
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
EN 60068-2-27:2009 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
IEC 60068-2-54:2006 Environmental testing - Part 2-54: Tests - Test Ta: Solderability testing of electronic components by the wetting balance method
EN 60068-2-17:1994 Environmental testing - Part 2: Tests - Test Q: Sealing
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
EN 61193-2 : 2007 QUALITY ASSESSMENT SYSTEMS - PART 2: SELECTION AND USE OF SAMPLING PLANS FOR INSPECTION OF ELECTRONIC COMPONENTS AND PACKAGES
EN 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60062:2016 Marking codes for resistors and capacitors
EN 60062:2016/AC:2016-12 MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016/COR1:2016)
EN 60068-2-29:1993 Environmental testing - Part 2: Tests - Test Eb and guidance: Bump
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
EN 60068-2-13:1999 Environmental testing - Part 2: Tests - Test M: Low air pressure
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
IEC 60063:2015 Preferred number series for resistors and capacitors
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
IEC 60068-2-29:1987 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
IEC 60717:2012 Method for the determination of the space required by capacitors and resistors with unidirectional terminations
EN 60068-2-54:2006 Environmental testing - Part 2-54: Tests - Test Ta: Solderability testing of electronic components by the wetting balance method
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
IEC 60469-2:1987 Pulse techniques and apparatus. Part 2: Pulse measurement and analysis, general considerations
EN 60695-11-5:2017 Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-45:1992/A1:1993 Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60068-2-69:2017 Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
£97.92
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.