• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 60695-11-20:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

FIRE HAZARD TESTING - PART 11-20: TEST FLAMES - 500 W FLAME TEST METHODS
Available format(s)

Hardcopy , PDF

Superseded date

23-11-2021

Language(s)

English

Published date

01-01-2015

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Significance of the fire tests
6 Apparatus
7 Test specimens
8 Test procedure
Annex A (normative) - Detailed requirements for the
        flame application point
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Explains a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products.

DevelopmentNote
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
76
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
IEC 60695-1-30:2017 Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
IEC 60695-4:2012 Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products
ISO 845:2006 Cellular plastics and rubbers Determination of apparent density
ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
ISO 13943:2017 Fire safety — Vocabulary
EN ISO 294-2:1998/A1:2005 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 2: SMALL TENSILE BARS
EN ISO 293:2005 Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004)
EN ISO 845:2009 Cellular plastics and rubbers - Determination of apparent density (ISO 845:2006)
ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
EN 60695-4:2012 FIRE HAZARD TESTING - PART 4: TERMINOLOGY CONCERNING FIRE TESTS FOR ELECTROTECHNICAL PRODUCTS (IEC 60695-4:2012)
EN 60695-11-3:2012 Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods
IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN ISO 295 : 2004 PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
IEC 60695-11-3:2012 Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
EN ISO 13943:2017 Fire safety - Vocabulary (ISO 13943:2017)
ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
IEC 60695-1-10:2016 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
ISO 16012:2015 Plastics Determination of linear dimensions of test specimens
EN ISO 294-1:2017 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)
EN ISO 294-3 : 2003 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 3: SMALL PLATES

View more information
£97.92
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.