• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 61347-1:2015

Current
Current

The latest, up-to-date edition.

LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2015

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Terminals
9 Earthing
10 Protection against accidental contact with live parts
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings of ballasts
14 Fault conditions
15 Construction
16 Creepage distances and clearances
17 Screws, current-carrying parts and connections
18 Resistance to heat, fire and tracking
19 Resistance to corrosion
20 No-load output voltage
Annex A (normative) - Test to establish whether a
        conductive part is a live part which may cause
        an electric shock
Annex B (normative) - Particular requirements for
        thermally protected lamp controlgear
Annex C (normative) - Particular requirements for
        electronic lamp controlgear with means of
        protection against overheating
Annex D (normative) - Requirements for carrying out
        the heating tests of thermally protected lamp
        controlgear
Annex E (normative) - Use of constant S other than
        4500 in tw tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of
        the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Additional requirements for
        built-in magnetic ballasts with double or
        reinforced insulation
Annex J (normative) - Schedule of more onerous
        requirements
Annex K (informative) - Conformity testing during
        manufacture
Annex L (normative) - Particular additional requirements
        for controlgears providing SELV
Annex M (informative) - Dielectric strength test voltages
        for controlgear intended for the use in impulse
        withstand Category III
Annex N (normative) - Requirements for insulation materials
        used for double or reinforced insulation
Annex O (normative) - Additional requirements for built-in
        electronic controlgear with double
        or reinforced insulation
Annex P (normative) - Creepage distances and clearances
        and distance through isolation (DTI) for lamp
        controlgear which are protected against pollution
        by the use of coating or potting
Annex Q (informative) - Example for Up calculation
Annex R (informative) - Concept of creepage distances
        and clearances
Annex S (informative) - Examples of controlgear
        insulation coordination
Annex T (informative) - Creepage distances and clearances
        for controlgear with a higher degree of availability
        (impulse withstand category III)
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Describes general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1000 V at 50 Hz or 60 Hz.

DevelopmentNote
Together with the parts 2-1 to 2-9 of I.S. EN 61347, supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
262
PublisherName
National Standards Authority of Ireland
Status
Current
Supersedes

Standards Relationship
NBN EN 61347-1 : 2015 Identical
UNE-EN 61347-1:2016 Identical
DIN EN 61347-1 : 2016 COR 1 2017 Identical
SN EN 61347-1 : 2001 Identical
EN 61347-1:2015 Identical
BS EN 61347-1:2015 Identical
NF EN 61347-1 : 2015 Identical

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60906-3:1994 IEC System of plugs and socket-outlets for household and similar purposes - Part 3: SELV plugs and socket-outlets, 16 A 6V, 12 V, 24 V, 48 V, a.c. and d.c.
IEC 60038:2009 IEC standard voltages
IEC 60730-2-3:2006 Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
EN 61558-2-16:2009/A1:2013 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013)
IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
EN 61347-2-9:2013 Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
EN 60085:2008 Electrical insulation - Thermal evaluation and designation
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
EN 61558-1:2005/A1:2009 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS
IEC 61347-2-9:2012 Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
IEC TR 60083:2015 Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
IEC 61558-2-16:2009+AMD1:2013 CSV Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units
EN 60691:2016 Thermal-links - Requirements and application guide
IEC 60929:2011+AMD1:2015 CSV AC and/or DC-supplied electronic control gear for tubularfluorescent lamps - Performance requirements
EN 60216 : 1990
IEC 61047:2004 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements
IEC 62384:2006+AMD1:2009 CSV DC or AC supplied electronic control gear for LED modules - Performance requirements
EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters)
EN 60923:2005/A1:2006 AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS
EN 60317-0-1:2014 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
IEC 60925:1989+AMD1:1996+AMD2:2001 CSV DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements
EN 60921:2004/A1:2006 BALLASTS FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS
IEC 60921:2004+AMD1:2006 CSV Ballasts for tubular fluorescent lamps - Performance requirements
IEC 61558-1:2017 Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests
IEC 60901:1996+AMD1:1997+AMD2:2000 CSV Single-capped fluorescent lamps - Performance specifications
IEC 60317-0-1:2013 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEEE 101 : 1987 GUIDE FOR THE STATISTICAL ANALYSIS OF THERMAL LIFE TEST DATA
EN 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60364-4-44:2007+AMD1:2015 CSV Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
IEC 60691:2015 Thermal-links - Requirements and application guide
IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60730-2-3:2007 AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS
IEC 61347-2-2:2011 Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
IEC 60927:2007+AMD1:2013 CSV Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements
HD 193 : 200S2 VOLTAGE BANDS FOR ELECTRICAL INSTALLATIONS OF BUILDINGS
IEC 60664-3:2016 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60884-2-4:2007 Plugs and socket-outlets for household and similar purposes - Part 2-4: Particular requirements for plugs and socket-outlets for SELV
EN 60901:1996/A6:2017 SINGLE-CAPPED FLUORESCENT LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60901:1996/A6:2014, MODIFIED)
EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
IEC 61180-1:1992 High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements
EN 60664-4:2006/corrigendum:2006 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS
ISO 4046-4:2002 Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 60155:1993 Glow-starters for fluorescent lamps
EN 60695-11-5:2017 Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
IEC 60923:2005+AMD1:2006 CSV Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements
IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
HD 243 : S12 GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 61189-2:2006 Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures
IEC 61347-2-8:2000+AMD1:2006 CSV Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps
EN 61180-1:1994 High-voltage test techniques for low-voltage equipment - Part 1: Definitions, test and procedure requirements
IEC 60990:2016 Methods of measurement of touch current and protective conductor current
EN 61189-2:2006 Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures

View more information
£136.36
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.