• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 877:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
Available format(s)

Hardcopy , PDF

Superseded date

17-11-2021

Language(s)

English

Published date

01-01-2000

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative References
3 Definitions
4 Technical Requirements
  4.1 General
  4.2 Dimensions
  4.3 Interconnection
  4.4 Mass
  4.5 Material characteristics of pipes, fittings and accessories
  4.6 Coatings for pipes, fittings and accessories
  4.7 Joints
  4.8 Buried systems
  4.9 Rainwater systems installed outside buildings
  4.10 Marking
5 Test Methods
  5.1 Surface condition
  5.2 Dimensions
  5.3 Mass
  5.4 Tensile strength of pipes and fittings
  5.5 Brinell hardness
  5.6 Ring crush test for grey cast iron pipes
  5.7 Coatings
  5.8 Joints
  5.9 Buried systems
  5.10 Rainwater systems installed outside buildings
  5.11 Marking
6 Evaluation of conformity
Annex A (informative) Other dimensions for buried systems
Annex B (informative) Other dimensions for rainwater systems to
        be installed outside buildings
Annex C (informative) Field of use for buried pipes and fittings,
        characteristics of soils, load-bearing capacity
Annex D (normative) Evaluation of conformity
Annex E (informative) Surveillance by an accredited third
        party (certification by third party)
Annex F (informative) General information on some product
        characteristics
Annex G (informative) Method of calculation of gross calorific
        potential of external coatings for the
        range, noted PCS[range ext. coating]
Annex H (normative) Reaction to fire test (SBI
        adaptation for testing a products range)
Annex ZA (informative) Clauses of the European Standard
         addressing essential requirements or other provisions
         of EU Directives
Bibliography

Defines cast iron pipeline components used for the construction of discharge systems for drains and building normally as gravity systems. The range is from DN 40 to DN 600 inclusive. Covers requirements for the dimensions and tolerances, appearance, materials, mechanical properties, standard coatings for cast iron pipes, fittings and accessories. These cover all components including joints. Quality assurance is covered in an information annex.

DocumentType
Standard
Pages
86
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

ISO 7724-1:1984 Paints and varnishes Colorimetry Part 1: Principles
EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
EN 605 : 1992 PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 1716:2010 Reaction to fire tests for products Determination of the gross heat of combustion (calorific value)
EN 20898-1 : 1991 MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS AND STUDS
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
ISO 2808:2007 Paints and varnishes Determination of film thickness
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
ISO/IEC 17011:2004 Conformity assessment General requirements for accreditation bodies accrediting conformity assessment bodies
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
ISO 7253:1996 Paints and varnishes — Determination of resistance to neutral salt spray (fog)
EN 476:2011 General requirements for components used in drains and sewers
ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 10204:2004 Metallic products - Types of inspection documents
ISO 9001:2015 Quality management systems — Requirements
ISO 2812-1:2017 Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water
EN 14366:2004 Laboratory measurement of noise from waste water installations
ISO 185:2005 Grey cast irons Classification
EN 10003-1 : 1994 METALLIC MATERIALS - BRINELL HARDNESS TEST - TEST METHOD
PREN 1366-3 : DRAFT 1993 FIRE TESTS FOR BUILDING ELEMENTS AND COMPONENTS - FIRE RESISTANCE TESTING OF SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
ISO 2409:2013 Paints and varnishes Cross-cut test
EN ISO 1716:2010 Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010)
EN ISO 11925-2:2010/AC:2011 REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
ISO 4628-2:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

View more information
£80.54
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.